• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2283-2286
• /
• 2003

This paper presents conservation of electrical energy in building with harmonics analysis and compensation which occur in electrical system. We use load controlling and management system in order to adjust load factor of system.The maximum demand limiting and controlling are used ,then the system can acquire the prediction and compare it to the maximum demand set point.The electrical signal analysis based on FFT technique. The harmonics are compensated by using harmonic filters.This system consists computer which works as controller, processor , analysis and database unit together with digital power meter in form of multidrop network through serial communication via RS-485.The load control system uses PLC to control load via serial communication RS-485. The A/D converter is used for sampling the electrical signals via parallel port of computer.The harmonic filters are controlled by a computer.The data of measurement such as voltage, current, power, power factor, total harmonic distortion, energy, etc., can be saved as database and analysis. The load factor is adjusted by limiting and controlling maximum demand. The load factor adjustment can reduce the cost of electric consumption and energy generation together with harmonics compensation in order to increase high efficiency of electrical system.

• Journal of Korea Multimedia Society
• /
• v.20 no.2
• /
• pp.271-278
• /
• 2017

This paper introduces a user-friendly PLC (programmable logic controller) monitoring and control system of heavy machinery using Android based smartphone. The proposed system will control diesel generator and many such like machine without a dedicated PC with respect to similar system and offers a new communication protocol for handling it. The smartphone controls the generator via Wi-Fi, through which it connects to the Raspberry pi which will be installed in the PLC panel to setup the communication between them. Furthermore, Raspberry pi connects to two devices, one is PLC which gives the status and current information of the machine and to ON/OFF the machine. This proposed system used RS485 as a key mediator for data exchanging between Raspberry PI(master) and PLC(slave). RS485 allows multiple devices (up to 32) to communicate at half duplex on single pair of wires and provides a long connectivity area (up to 1200 meters) as compared to another device. This proposed system specially focused on accurate data flow between smartphone and PLC panel.

• Journal of Biomedical Engineering Research
• /
• v.18 no.4
• /
• pp.373-380
• /
• 1997

In this paper, we describe the intrabed network in a patient monitoring system we developed The intrabed network handles data communication between the main unit of a bedside patient monitor and parameter modules plugged in it. We designed the intrabed network based on RS-485 and HDLC protocol with 1 Mbps data rate. Message exchanges are implemented based on three data structures of packet frame. and stream. We present the specification and the performance of the data communication network for the developed patient monitor.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.2
• /
• pp.182-189
• /
• 2007

This paper describes the implementation of control and monitoring system of ship's lamps at local area using power line communication method, power line modem(PLM). We design modem, microprocessor interface for electric power control by frequency control and analog to digital signal conversion, lamp device. PLM communication is very economical using existing electric power line unlike RS-232, RS-485 communications. We verify and confirm by experimental work that control and monitor lamp system for ship by an PLM communication.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1177-1182
• /
• 2016

The most industrial instruments for monitoring and control are occurring the extension problem and the external protocol compatibility. In this paper, we developed the boards for the industrial communication monitoring that are able to convert the protocol in various communication between devices and instruments. These are consisted the main board and several sub-board. They can have extension using the main board connection. The sub-board support the each communication method or data transfer. The main board was used the Atmega 2560 Microprocessor of AVR series, and the sub-boards are have the Atmega 256 or Atmega 128 in the AVR series. We have designed to connect the sub-board using placed the 4 RS485 serial slots in the main board. The sub-boards were developed to support the analog and digital I/O. These are able to have monitoring by CAN and Ethernet communication. The experimental results, we obtained good data transfer rate and conversion rate.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.5
• /
• pp.44-51
• /
• 2009

In this paper, an air conditioner peak power control system using electric power line communication has been developed. The air conditioner power control system using RS-485 communication method is hard to install on the existing buildings due to difficulty in cabling, and the system using wireless communication methods has a weak point of not being able to be used in close space, while the developed system has its own advantages of overcoming the above mentioned obstacles. In addition, the system is extended to support not only single-phase electricity system but also three-phase four-wire electricity system, and therefore can be installed anywhere in the domestic environment. The system also has enhanced the ease of deployment, operational stability and economical efficiency by compact circuit design. Considering the current state requiring the energy sayings, the system would greatly contribute to the widespread use of the air conditioner power control system. The superiority in the performance and stability of the system has been proved by the design verification of each component such as remote air conditioner controller, electric power line gateway and so on, and the field test of the whole system.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1779_1781
• /
• 2009

The main contents of this paper is to design a system that can remote control the most of the LED lighting device in the market. In order to realize the device driver, we choose the communication mode Zigbee, PLC, RS232 and RS485. Using client-server system, LED lighting device can be controlled just through web browser.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.88-92
• /
• 1999

This paper aims at developing remote contro system to control and monitor distributed various devices through internet or information communication network. SNMP (Simple Network Management Protocol) and rectifier operated in a row are adopted for network management protocol and applied device, respectively. For controlling and monitoring distributed devices in real-time java-environment software is constructed. Also general-use interface controller between network device and applied device is proposed. Finally, seria communication such as RS-232 and RS-485 is used between controller and applied device.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3159-3161
• /
• 1999

This paper aims at developing remote control system to control and monitor distributed various devices through internet or information communication network. SNMP (Simple Network Management Protocol) and UPS (Uninterruptible Power Supply) are adopted for network management protocol and applied device, respectively. For controlling and monitoring distributed devices in real-time, Java-environment software is constructed. Also, general-use interface controller between network device and applied device is proposed. Finally, serial communication such as RS-232 and RS-485 is used between controller and applied device.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.7
• /
• pp.83-90
• /
• 2004

This paper describes on-board decentralized data acquisition system that acquires and encodes the numerous sensor data distributed on the big flight vehicles efficiently. The system's sub-units which have one encoder unit and several remote units were designed and simulated according to the communication protocols and the control, sequence logics based on the FPGA chip. And we have made the functional verification of the acquisition, collection and formatting of remote analog and digital data for the manufactured hardwares.