• International Journal of Naval Architecture and Ocean Engineering
• /
• v.2 no.1
• /
• pp.24-33
• /
• 2010

Design of a Pump Jet Propulsor (PJP) was undertaken for an underwater body with axisymmetric configuration using axial/low compressor design techniques supported by Computational Fluid Dynamics (CFD) analysis for performance prediction. Experimental evaluation of the PJP was earned out through experiments in a Wind Tunnel Facility (WTF) using momentum defect principle for propulsive performance prior to proceeding with extensive experimental evaluation in towing tank and cavitation tunnel. Experiments were particularly conducted with respect to Self Propulsion Point (SPP), residual torque and thrust characteristics over a range of vehicle advance ratio in order to ascertain whether sufficient thrust is developed at the design condition with least possible imbalance torque left out due to residual swirl in the slip stream. Pumpjet and body models were developed for the propulsion tests using Aluminum alloy forged material. Tests were conducted from 0 m/s to 30 m/s at four rotational speeds of the PJP. SPP was determined confirming the thrust development capability of PJP. Estimation of residual torque was carried out at SPP corresponding to speeds of 15, 20 and 25 m/s to examine the effectiveness of the stator. Estimation of thrust and residual torque was also carried out at wind speeds 0 and 6 m/s for PJP RPMs corresponding to self propulsion tests to study the propulsion characteristics during the launch of the vehicle m water where advance ratios are close to Zero. These results are essential to assess the thrust performance at very low advance ratios to accelerate the body and to control the body during initial stages. This technique has turned out to be very useful and economical method for quick assessment of overall performance of the propulsor and generation of exhaustive fluid dynamic data to validate CFD techniques employed.

• Korean Journal of Agricultural Science
• /
• v.44 no.4
• /
• pp.595-603
• /
• 2017

Crop growth and production cost are greatly influenced by management of environmental factors such as ambient temperature, humidity, and $CO_2$, especially in protected horticulture. Opening and closing of greenhouses is the most important operation for control of these ambient environmental factors, and precise and stable operation requires high performance window motors. In this study, a 400 W precise window motor was constructed, and its performance was evaluated for plastic and glass greenhouses. First, the motor was designed and fabricated by benchmarking of an advanced foreign product. Then, the performance was evaluated through vibration, PCB (Process Control Block), and load tests. Vibration tests resulted in averaged vibration displacement and velocity of the developed motor of 0.002 mm and 0.2267m/s, which were statistically significantly different from those of the target motor. Average vibration acceleration ($0.26m/s^2$) of the developed motor was also significantly different from that ($0.51m/s^2$) of the target motor. PCB tests showed 2 - 4 mm deviation from the target values, and confirmed the operating status and precision of the control. Load tests with a 300 kg load also showed acceptable operating status and durability. Current values were $1.31{\pm}0.06A$ and RPMs were in the range of 2.9 - 3.0. Considering the above results, the developed window motor would be competitive to the target foreign product.

• Journal of Biosystems Engineering
• /
• v.35 no.1
• /
• pp.15-20
• /
• 2010

Tractor PTO output and fuel consumption rate under the korean paddy and various paddy operations were measured and analyzed, in which all the measurements were accomplished by the OECD tractor test codes and the collected information will be utilized for defining tractor energy efficiency class and its test methods. Tractor PTO performance tests were conducted under full-load, part-load and various engine RPMs with part-load at the engine laboratory, while the paddy operations were dry land plowing, wet and dry land rotary tilling and wet land preparation under various soils. As a whole, the rated tractor outputs were ranged from 17% to 100% in the various tillage and land preparation operations, however, the loads for the paddy operations of 1,700 to 2,000 rpm were very close to the OECD tractor load distribution thus it would be appropriate to adopt OECD tractor test codes to measure energy consumption efficiency of tractor.

• Journal of the Korean Ceramic Society
• /
• v.54 no.1
• /
• pp.49-54
• /
• 2017

In this study, based on hydrolysis and condensation via $St{\ddot{o}}ber$ process of sol-gel method, synthesis of mono-dispersed silica nanoparticles was carried out with hydrophilic solvent. This operation was expected to be a more simplified process than that with organic solvent. Based on the sol-gel method, which involves simply controlling the particle size, the particle size of the synthesized silica specimens were ranged from 30 to 300 nm by controlling the composition of tetraethylorthosilicate (TEOS), DI water and ammonia solution, and by varying the stirring speeds while maintaining a fixed amount of ethanol. Increasing the content of DI water and decreasing the content of ammonia caused the particle size to decrease, while controlling the stirring speed at a high level of RPMs enabled a decrease of the particle size. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) were utilized to investigate the success factors for synthesizing process; Field emission scanning electron microscopy (FE-SEM) was used to study the effects of the size and morphology of the synthesized particles. To analyze the dispersion properties, zeta potential and particle size distribution (PSD) analyses were utilized.

• Journal of Animal Environmental Science
• /
• v.20 no.1
• /
• pp.1-8
• /
• 2014

The study on design criteria of solid-liquid separator for dairy farms was done by testing various screens, presses, and RPMs of screw auger with remodeled screw-press type pig-manure separator. The moisture content of separated solid increase from 68.3% to 74.2% as auger rotating speed increased from 9.8 to 29.2 RPM at 34.8 kPa of pressure and 1.0 mm of slit wedge wire screen condition. The moisture contents of separated solid were 72~77%, work efficiencies were 16~18 kg/min at 1.0 mm of slit wedge wire screen. The efficiency was higher than one at 0.5 mm of slit wedge wire screen, which was used to separate for pig manure. The best work efficiency was 18 kg/min at 42.5 kPa, 1.0 mm slit screen. The separated solid moisture content was 75% at this condition.

• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3907-3912
• /
• 2023

Radiation portal monitors (RPMs) installed at airports and harbors to prevent illicit trafficking of radioactive materials generally use large plastic scintillators. However, their energy resolution is poor and radionuclide identification is nearly unfeasible. In this study, to improve isotope identification, a RPM system based on a multi-array plastic scintillator and convolutional neural network (CNN) was evaluated by measuring the spectra of radioactive sources. A multi-array plastic scintillator comprising an assembly of 14 hexagonal scintillators was fabricated within an area of 50 × 100 cm². The energy spectra of ¹³⁷Cs, ⁶⁰Co, ²²⁶Ra, and ⁴K (KCl) were measured at speeds of 10-30 km/h, respectively, and an energy-weighted algorithm was applied. For the CNN, 700 and 300 spectral images were used as training and testing images, respectively. Compared to the conventional plastic scintillator, the multi-arrayed detector showed a high collection probability of the optical photons generated inside. A Compton maximum peak was observed for four moving radiation sources, and the CNN-based classification results showed that at least 70% was discriminated. Under the speed condition, the spectral fluctuations were higher than those under dwelling condition. However, the machine learning results demonstrated that a considerably high level of nuclide discrimination was possible under source movement conditions.

• Journal of Aerospace System Engineering
• /
• v.12 no.6
• /
• pp.23-31
• /
• 2018

In the present work, the thrust and torque of multicopter propellers in hovering are predicted based on BET method. The geometry information of the propellers is obtained using a three dimensional scanner and the airfoil section is extracted using CATIA. EDISON CFD is adopted to calculate the drag and lift of airfoil at a given geometry and flow conditions and then thrust is calculated with respect to a given RPMs based on BET. Two simulations with laminar and turbulent flows are considered. The predicted value is compared with the performance data from the Product Company and results from JavaProp software, which is used in the design and prediction of propellers. In the case of a 9-inch propeller, the thrust from the product company is corresponding to the results between the laminar and turbulent flow conditions. In the 16-inch case, the predicted thrust at turbulent flow conditions conformed well with reference one. The predicted torque shows a big difference with the reference data.

• Journal of Animal Reproduction and Biotechnology
• /
• v.34 no.1
• /
• pp.57-63
• /
• 2019

This study was conducted to find out the effect that ${\kappa}-Carrageenan$ has on the properties of dog sperm when it was added to the cryoprotectant. Extender basically was contained 1.21 g Trizma base, 0.67 g citric acid, 0.4 g glucose, 0.03 g penicillin G, 0.05 g streptomycin sulfate. Extender1 was added with 0.1%, 0.2%, 0.3%, and 0.5% carrageenan, while extender2 was supplemented with glycerol. After freezing-thawing, the motility, viability, acrosome integrity, apoptosis, and ROS (reactive oxygen specifications) of sperm were measured to analyze the effects of the supplementation of carrageenan. Total Motile (TM), Rapid Progressive Motile (RPM), Medium Progressive Motile (MPM), and Immotile were measured through the CASA system after thawing in 37 degree water. Extender with 0.2% ${\kappa}-carrageenan$ ($64.26{\pm}0.49$) was significantly higher than control ($40.24{\pm}8.27$) (p < 0.05). RPMs of extender with 0.1%, 0.2% ${\kappa}-carrageenan$ ($57.64{\pm}6.34$, $56.47{\pm}1.35$) were significantly higher than the other groups (p < 0.05). Acrosome integrity was measured by dyeing to PSA-FITC with an epifluorescence microscope. Normal acrosome ratio of extender with 0.5% ${\kappa}-carrageenan$ ($61{\pm}8.03$) was higher than the other groups (p < 0.05). Apoptosis was measured with a FACSCalibur flow cytometer using FITC (FITC Annexin V Apoptosis Detection Kit). Treated groups of ${\kappa}-carrageenan$ of 0.1% ($0.81{\pm}0.05$), 0.2% ($0.85{\pm}0.05$) were significantly higer (p < 0.05) than control. Modified SYBR/PI staining was used for determination of viability and DCF staining was used for evaluation of ROS. Viability and ROS were not significantly different from other groups. In conclusion, adding a certain concentration of carrageenan to the extender of cryopreservation, carrageenan contributes to the improvement of the sperm motility, acrosome integrity and prevention of apoptosis.

• Analytical Science and Technology
• /
• v.21 no.2
• /
• pp.148-157
• /
• 2008

To describe the lifetime prediction of gas turbine core parts serviced in some ten thousands rpms at over $1,000^{\circ}C$, the Larson-Miller Creep Curves, which are formed by creep rupture tests as the destructive experiment with parameters of stress and temperature, are used often, but not exact and reliable with errors of over some tens. On the other hand, this study shows a non-destructive method with increased accuracy and reliability. The SEM and TEM specimens were extracted by replica after polishing the local airfoil and root surfaces of the first stage scraped blade (bucket), serviced for 18,000 hours at $1,280^{\circ}C$ in Gas Turbines of Boryong. The observed TEM and SEM precipitates were digitalized for calculation of the average size. Here we could find the precipitate size grown from $0.45{\mu}m$ to $0.6{\mu}m$ during service and the grown precipitates to be still sound. From these results we could conclude that the scraped balde can be used for ten thous and hours additionally and for twenty thousand hours by additional heat treatments on the scraped blade.