• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.93-100
• /
• 2009

This paper presents a step up four channel DC-DC converter using charge pump voltage doubler structure. Our goal is to design and implement DC-DC converter for capacitive SP4T RF MEMS switch in front end module in wireless transceiver system. Charge pump structure is small and consume low power 3.3V input voltage is boosted by DC-DC Converter to $11.3{\pm}0.1V$, $12.4{\pm}0.1V$, $14.1{\pm}0.2V$ output voltage With 10MHz switching frequency. By using voltage level shifter structure, output of DC-DC converter is selected by 3.3V four channel selection signals and transferred to capacitive MEMS devices. External passive devices are not used for driving DC-DC converter. The total chip area is $2.8{\times}2.1mm^2$ including pads and the power consumption is 7.52mW, 7.82mW, 8.61mW.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.5
• /
• pp.472-478
• /
• 2003

In this paper, a near zero If mixer was designed in cascode structure by using two single-gate FETs. Since it is driven by the second order harmonic of LO signal, a sub-harmonic cascode FET mixer has good LO-RF port isolation characteristic. In order to solve DC offset of a homodyne system, near zero If is used instead of zero If and the mixer is driven by sub-harmonic of LO signal. As RF input power was -30 dBm and LO power was 6 dBm, the designed mixer had 6.7 dB conversion gain, 8.4 dB noise figure, 31.5 dB LO-RF port isolation, -1.9 dBm lIP3 and -2.8 dBm IIP2.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.1
• /
• pp.47-52
• /
• 2002

It was virtually declared that measurement science must abandon the error analysis of measurement when ISO had published "Guide to Expression of uncertainty in Measurement" International inclination of measurement field in order to guarantee the traceability and confidence of measurement results discards the error concept and instead analyzes the measurement uncertainty. In this paper we establish a mathematical model of measurement and analyze all uncertainty factors as possible as for yielding the measurement uncertainty in the course of the calibration of RF multimeter using Transfer Standard, Thermal Voltage Converter We produce the expanded uncertainty by analyzing cable effects, correlation of thermocoupler and DC meter, DC source, RF source, attenuator, reflection coefficients and DUT.s and DUT.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.1
• /
• pp.45-52
• /
• 2009

In this paper, a new rectenna is presented for the wireless transmission of microwave power using dipole antenna (Quasi Yagi effect) and rectifier of CPS resonator structure. The dipole antenna with CPW feedline has high peak gain than a general dipole antenna. A ground plane of CPW is used to reflect a dipole as a Yagi antenna. Therefore, the new rectenna receives the RF power better than the one using general dipole. A RF-to-DC conversion efficiency of 61 % using a 1.4 $k{\Omega}$ load resistor is obtained at 5.8 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.189-193
• /
• 2005

In this paper, we propose a direct conversion double-balanced down-converter fer MB-OFDM W system, which is implemented using $0.18\;{\mu}m$ CMOS technology and its measurement results are shown. The proposed down-converter adopts a resistive current-source instead of general transconductance stage using MOS transistor to achieve wideband characteristics over RF input frequency band $3\~5\;GHz$ with good gain flatness. The measured conversion gain is more than +3 dB, and gain flatness is less than 3 dB for three UWB channels. The dc consumption of this work is only 0.89 mA from 1.8 V power supply, leading to the low-power W application.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.12 s.115
• /
• pp.1156-1163
• /
• 2006

This paper presents an ultra wideband(UWB) direct conversion mixer for IEEE 802.15.3a applications with simulation and measurement results. Since the direct conversion mixing causes dc-offset and even-order distortion, the proposed mixer adopts an anti-parallel diode pairs(APDPs) to solve these problems. The proposed mixer consists of an in-phase wilkinson power divider over $3.1{\sim}4.8GHz$, a wideband $45^{\circ}$ power divider over $1.5{\sim}2.4GHz$, and miniatured band pass filters(BPFs) for RF-LO isolations. The conversion loss is optimized with impedance matchings between APDPs and wideband components. The measured mixer shows the conversion loss of 13.5 dB, input third-order intercept-point($IIP_3$) of 7 dBm, and 1-dB gam compression point($P_{1dB}$) of -4 dBm. Quadrature(I/Q) outputs have the magnitude difference of about 1 dB and phase difference of ${\pm}3^{\circ}$.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.3
• /
• pp.35-41
• /
• 2013

An efficient multi-stage rectifier for wireless power transfer in deep implant medical devices is implemented using $0.18-{\mu}m$ CMOS technology. The presented three-stage rectifier employs a cross-coupled topology to boost a small input AC signal from the external device to produce a 1.2-1.5 V output DC signal for the implant device. The designed rectifier achieves a maximum measured power conversion efficiency of 70% at 13.56 MHz under the conditions of a low 0.6-Vpp RF input signal with a $10-k{\Omega}$ output load resistance.

• Journal of Korea Society of Industrial Information Systems
• /
• v.16 no.4
• /
• pp.1-7
• /
• 2011

In this paper, we design rectifing circuits at 910MHz, which is used for passive RFID system, for wireless power transmission system by using two types of schottkey diodes HSMS_2822 and HSMS 2852, and the RF-DC conversion efficiencies for the curcuits are compared and analyzed in terms of input power and load resistance. When the input power is -20 to 17dBm, the conversion efficiency for HSMS_2852 is larger than in case of HSMS_2822. The output voltage and current at the load of the fabricated rectifying circuit are measured through a dipole antenna when input power is transmitted by a RFID reader and the diatance varies. The measured ouput volatge and current for the distance of 50cm are 2.5V and 5.75mA.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.4
• /
• pp.506-511
• /
• 2011

In this paper, a rectenna for wireless power transmission at 900MHz is proposed. Rectenna is a device transforming RF power into DC power and it may consist of a antenna, rectifying and charging circuits. In this paper, we designed a slot antenna to receive 900MHz signal, a rectifying circuit of about 40% efficiency at 0dBm input, and a charging circuit to store a weak power signal and supply constant voltage to load. From the experiment using a RFID reader as a transmitter for 1W power, it was found that the proposed rectenna receiving about 0dBm power can supply 3.3V constant voltage to 50$k{\Omega}$ load during 280sec.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.9
• /
• pp.2227-2235
• /
• 2009

This paper describes the system configuration and measured performances of a wireless power transmission system which utilizes microwave. The technically final target of this system is to provide DC power to various mobile terminals within limited spaces such as buildings, conference rooms, and so on. The prototype system is built using in-house designed and fabricated circuits such as microwave oscillator, high power amplifier, microstrip patch antenna, low pass filter, and detector/rectifier. The fixed RF power of 29.3dBm at 2.4GHz is produced from the high power amplifier and transmitted through the transmitting antenna, while the received RF power at the receiving antenna is transformed into DC power through the detector/rectifier. The measured change of DC voltage according to the distance between transmitting and receiving antenna is described.