• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.11
• /
• pp.45-52
• /
• 2005

In this paper, we propose the PLL system of the local oscillator system for the millimeter wave band's radio astronomy receiving system. The development of the proposed local oscillator system based on the YIG oscillator VCO with $26.5\~40GHz$ specification. This system consists of the oscillator part including the YIG VCO, the harmonic mixer, and the isolator, the RF processing part including the triplexer, limiter, and RF discrimination processor, and the PLL system including YIG modulator and controller. Based on this configuration, we verify the frequency and power stability of the developed local oscillator system according to some temperature variation. From this test results we confirm the stable output frequency and power characteristic peformance of the developed LO system at constant temperature.

• ETRI Journal
• /
• v.39 no.1
• /
• pp.51-61
• /
• 2017

This paper demonstrates a systematic approach for the design of broadband, high efficiency, high power, Class-AB RF amplifiers with high gain flatness. It is usually difficult to simultaneously achieve a high gain flatness and high efficiency in a broadband RF power amplifier, especially in a high power design. As a result, the use of a computer-aided simulation is most often the best way to achieve these goals; however, an appropriate initial value and a systematic approach are necessary for the simulation results to rapidly converge. These objectives can be accomplished with a minimum of trial and error through the following techniques. First, signal gain variations are reduced over a wide bandwidth using a proper pre-matching network. Then, the source and load impedances are satisfactorily obtained from small-signal and load-pull simulations, respectively. Finally, two high-order Chebyshev low-pass filters are employed to provide optimum input and output impedance matching networks over a bandwidth of 100 MHz-500 MHz. By using an EM simulation for the substrate, the simulation results were observed to be in close agreement with the measured results.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.4
• /
• pp.123-127
• /
• 2021

Millimeter-wave tracking radars should be operated in various environmental restrictions, thus they demand more computing power and smaller size compared to conventional tracking radars. This paper presents the design and implementation of the compact power supply for millimeter-wave tracking radar applications. To meet requirements of low voltage/high current and voltage accuracy for FPGA/DSP digital circuits, Point of Load (POL) converters are used in order to enhance power density and system efficiency. LDO (Low Dropout) is applied for the output voltage under the light load condition, then the single-input-multi-output power supply with max power of 375 W and 8 outputs is developed. The proposed power supply achieves output voltage accuracy of ±2 % and noise level of <50 mVpp % under full load conditions.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.93-100
• /
• 2009

This paper presents a step up four channel DC-DC converter using charge pump voltage doubler structure. Our goal is to design and implement DC-DC converter for capacitive SP4T RF MEMS switch in front end module in wireless transceiver system. Charge pump structure is small and consume low power 3.3V input voltage is boosted by DC-DC Converter to $11.3{\pm}0.1V$, $12.4{\pm}0.1V$, $14.1{\pm}0.2V$ output voltage With 10MHz switching frequency. By using voltage level shifter structure, output of DC-DC converter is selected by 3.3V four channel selection signals and transferred to capacitive MEMS devices. External passive devices are not used for driving DC-DC converter. The total chip area is $2.8{\times}2.1mm^2$ including pads and the power consumption is 7.52mW, 7.82mW, 8.61mW.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5A
• /
• pp.496-503
• /
• 2010

The implementation of a RF transceiver for WRAN(Wireless Regional Area Network) system based on IEEE 802.22 standard using Cognitive Radio technology is presented in this paper. A CMOS RF transceiver IC for WRAN system operates in VHF/UHF(54~862MHz) broadband, and employs dual-path direct-conversion configuration and the in-band harmonic distortions are effectively suppressed by exploiting the dual-path direct conversion architecture. For 64QAM(3/4 coding rate) OFDM signal, an EVM of <-31.4dB(2.7%) has been achieved at 10dBm off-chip PA output power and the total chip area with pads is 12.95 mm2. The experimental results show that the proposed CMOS RF transceiver IC has perfect performance for WRAN system based on TDD(Time Division Duplex) mode.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.6
• /
• pp.600-613
• /
• 1997

The implementation of a BTS(Base station Transceiver) for WLL system using W-CDMA(Wideband-Code Division Multiple Access) method is presented in this paper. It consists of three boards; receiver, transmitter and RF controller. Some RF parameters are considered and simulated by the RF simulation S/W using commercial and customized components specifications. The implemented transceiver of 5 MHz RF channel bandwidth satisfies the system requirements of a transceiver such as dynamic range, sensitivity in the receiver and spurious emission suppression in the transmitter. At the receiver, the experimental measurement showed 2.86 dB of NF and 60 dB above of dynamic range in AGC(Automatic Gain Control) locking. At the transmitter, the -49.46 dBc of spurious emission suppression is attained when the output power of the transmitter is 34.3 dBm. These results are good enough to meet to standard performance specifications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.7
• /
• pp.737-746
• /
• 2014

Recently, researches about MIMO(Multi-Input Multi-Output) system are being studied actively due to high-capacity and high-speed communication. However, MIMO system has many RF(Radio Frequency) chains according to many array antennas. So, MIMO system has disadvantages such as high-complexity and high-power-consumption. Also, it is impossible to miniaturize the antenna dimension. In order to solve these problems, beamspace MIMO system using ESPAR(Electronically Steerable Parasitic Array Radiator) antenna was proposed. It is possible to reduce the complexity and the power-consumption, because it has single RF chain by using one active antenna and several parasitic elements. In this paper, in order to improve the security, for the first time, chaos communication algorithm is applied to QPSK modulated beamspace MIMO system using ESPAR antenna. We define as chaos QPSK beamspace MIMO system, and evaluate the SER performance. Also, we confirm that QPSK symbols can be made by changing the reactance values of parasitic elements, and evaluate the SER performance of this system.

• The Journal of the Korea Contents Association
• /
• v.6 no.1
• /
• pp.8-13
• /
• 2006

In this thesis, an automatic door lock system using a dual tone multiple frequency(DTMF) signal generated as pushing the key button of mobile phone is proposed and implemented. This system consists of a transmitter module and a receiver module for processing the DTMF signal of mobile phone. The DTMF signal of mobile phone connected with ear-phone jack enter into the input terminal of DTMF receiver and those are encoded by a code-converter with 4-bits binary format in the DTMF receiver. The encoded output signals are transmitted to the amplitude shift keying(ASK) modulator of transmitter module and the modulated ASK signals which are converted into radio frequency(RF) signals propagate in a free space. The RF signals passed through a free space are demodulated by the ASK demodulator of receiver module and the demodulated ASK signals are sent to a micro-controller unit(MCU). The output signals processed by the MCU are compared with the secreted identification number which is prerecorded in a microprocessor and are transferred to a power relay. If the result is the same, the automatic door lock system opens a door. In the opposite case, it maintains closing the door. The implemented automatic door lock system operates well in mobile environments.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2022.06a
• /
• pp.339-343
• /
• 2022

In this study, a method for simplifying the structure of the VDES RF receiver, and the gain control method of the receiver to comply with the international standard in this structure was described. The input level of the wanted signal and unwanted signal to the receiver was defined, and when the two signals were input, the saturation state at the ADC was checked at the receiver output. As a result of the simulation by the circuit simulator, it was satisfied that the output power of the receiver was in the SFDR region of ADC with respect to the adjacent channel interference ratio, intermodulation, and blocking level. Through this study, it was found that the structure of th proposed RF receiver conforms to the international standard.

• Journal of Navigation and Port Research
• /
• v.27 no.4
• /
• pp.437-441
• /
• 2003

In this paper, the 30 W power amplifier for an IMT-2000 repeater was developed a gain flatness and the third IMD (Intermodulation distortion) by microwave absorber. The absorption ability of the absorber is shown up to -10 dB and -4 dB at 3.6 GHz, 2.3 GHz band, respectively. The power amplifier without absorber has the gain over 57 dB, the gain flatness of $\pm$0.33 dB and the third IMD of 27 dBc at 33.3 W output. Otherwise, the power amplifier with absorber has the gain over 58 dB, the gain flatness of less than $\pm$0.9, the third IMD over 29 dBc at the same output power. As a result, the characteristic of the different type shows improvement of 1 dB in gain, 0.3 dB in gain flatness and 1.77 dBc in IMD.