• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.395-398
• /
• 2000

Reactive radio frequency (RF)magnetron sputter with incident angle has been used to deposit AlN thin film on a crystalline Si substrate. (002)Preferred orientation of AlN thin film has been obtained at low sputtering pressure. Also it has been shown that depostion rate of AIN thin film is affected by fraction Ar and $N_2$ partial pressure. But substrate temperature didn't affect depostion rate of AIN thin film . As sputtering pressure increased preferred orientation degraded. The internal stress changed from tensile stress to compressive stress as fraction of $N_2$ partial pressure increased. At low nitrogen partial pressure cermet$^{[1]}$ AIN thin film is obtained.

• Journal of Surface Science and Engineering
• /
• v.33 no.4
• /
• pp.266-272
• /
• 2000

Sputtered $MoS_2$ thin films provide lubrication and wear improvements for vacuum and space applications. In this study, deposition of $MoS_2$ thin films by R.F. magnetron sputtering was studied with regard to the micro-structural change of $MoS_2$ film and mechanical properties. The coating parameters such as the working pressure, the RF power, the substrate temperature, the etching time were varied to determine how these parameters affected the film morphology and mechanical properties of deposited films. The best wear properties and critical load were observed with the film deposited at $70^{\circ}C$, 1.0$\times$$10^{ -3}$ Torr, 170W and 1 hour deposition time. The critical load increased with the increase of sputter etching time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.446-447
• /
• 2007

The rapid thermal annealing effect of transparent IZTO(indium zinc oxide) and IAZO(indium alminium zinc oxide) films grown on glass substrate for solar cell or flat panel displays(FPDs) was studied. We prepared IZTO using RF magnetron sputtering and IAZO using DC co-sputtering method. Subsequently, using rapid thermal annealing(RTA) system, prepared IZTO and IAZO films were annealed at 300, 400, 500, $600^{\circ}C$ for 90sec. In addition, Electrical and optical characteristics were measured by Hall effect measurement and UV/Vis spectrometer examinations, respectively. To analyze structural properties and surface smoothness of the IZTO and IAZO films, XRD and SEM examinations were performed, respectively. It was shown that IZTO and IAZO films exhibited microcrystalline structure over $400^{\circ}C$ and amorphous structural regardless of RTA temperature, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.206-206
• /
• 2009

RF Magnetron Sputtering 방법을 통해 ZnS:Mn 박막 형광체를 증착한 다층 TFEL (Thin-Film Electroluminescent) Backlight 소자를 제작하였다. Alumina 기판 위에 Au 전극과 PMN 후막 유전체를 Screen printing 기법으로 층을 형성하였다. 그 위에 MgO 박막 유전체를 E-Beam 장비를 이용하여 증착 후, ZnS:Mn 박막 형광체를 50 W 의 저전력으로 약 8000 ${\AA}$ 두께로 증착하였다. 형광체는 Sputter 증착 시 Sulfur 부족 현상을 보상해주기 위해 ZnS:Mn (0.5%) Target 에 2 at % 의 Sulfur를 첨가하였으며, 상부 전극으로 사용할 ITO 는 DC Magnetron Sputter 를 이용하여 증착하였다. 어닐링 공정은 Air 분위기에서 급속 열처리 장치 (RTA, Rapid Thermal Annealing) 을 이용하여 600 $^{\circ}C$에서 20 분 진행하였다. 이러한 과정들을 통해 저전압 고휘도의 TFEL Backlight 소자를 제조할 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05d
• /
• pp.100-104
• /
• 2003

$BaTiO_3$ ceramic thin films were manufactured by rf/dc magnetron sputter technique. We have investigated crystal structure, surface morphology and PTCR(positive-temperature coefficient of resistance) characteristics of the specimen depending on second heat-treatment temperatures. Second heat treatments of the specimen were performed in the temperature range of 400 to $1350^{\circ}C$. X-ray diffraction patterns of $BaTiO_3$ thin films show that the specimen heat treated below $600^{\circ}C$ is an amorphous phase and the one heat treated above $1100^{\circ}C$ forms a poly-crystallization. In the specimen heat-treated at $1300^{\circ}C$, a lattice constant ratio (c/a) was 1.188. Scanning electron microscope(SEM) image of $BaTiO_3$ thin films of the specimen heat treated in between 900 and $1100^{\circ}C$ shows a grain growth. At $1100^{\circ}C$, the specimen stops grain-growing and becomes a poly-crystallization.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.188-188
• /
• 2011

Recently, scaling down of ULSI (Ultra Large Scale Integration) circuit of CMOS (Complementary Meta Oxide Semiconductor) based electronic devices, the electronic devices, become much faster and smaller size that are promising property of semiconductor market. However, very narrow interconnect line width has some disadvantages. Deposition of conformal and thin barrier is not easy. And metallization process needs deposition of diffusion barrier and glue layer for EP/ELP deposition. Thus, there is not enough space for copper filling process. In order to get over these negative effects, simple process of copper metallization is important. In this study, Cu-V alloy layer was deposited using of DC/RF magnetron sputter deposition system. Cu-V alloy film was deposited on the plane SiO2/Si bi-layer substrate with smooth surface. Cu-V film's thickness was about 50 nm. Cu-V alloy film deposited at $150^{\circ}C$. XRD, AFM, Hall measurement system, and AES were used to analyze this work. For the barrier formation, annealing temperature was 300, 400, $500^{\circ}C$ (1 hour). Barrier thermal stability was tested by I-V(leakage current) and XRD analysis after 300, 500, $700^{\circ}C$ (12 hour) annealing. With this research, over $500^{\circ}C$ annealed barrier has large leakage current. However vanadium-based diffusion barrier annealed at $400^{\circ}C$ has good thermal stability. Therefore thermal stability of vanadium-based diffusion barrier is desirable for copper interconnection.

• Korean Journal of Crystallography
• /
• v.6 no.2
• /
• pp.134-140
• /
• 1995

SAW properties of SiNx/ZnO bilayer thin film structure were analyzed. ZnO thin films were deposited by rf magnetron sputter using O2 gas as an oxidizer. Structure of ZnO thin films was affected by Ar/O2 ratio. At the gas ratio of Ar/O2=67/33, the standard deviation of X-ray rocking curve of (002) preferred ZnO thin film was 2.17 degree. This value is sufficient to use ZnO thin films as an acoustic element. SAW velocity of glass/SiNx(7000Å)/Al/ZnO(5μm) structure was max. 2.2% faster than that of ZnO/glass.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.52.2-52.2
• /
• 2011

본 연구의 목적은 CIGS 태양전지의 두 가지 TCO층 중 AZO를 제외한 intrinsic ZnO의 전자빔 처리 영향에 대한 특성 분석을 하고자 함이다. 또한 추후 CIGS 태양전지를 제조하여 적용 시 전자빔 처리 전후의 특성이 어떻게 변하는지를 알아보기 위한 사전 실험이다. Intrinsic ZnO는 RF magnetron sputter 를 이용하여 약 100nm의 두께로 증착 하였다. 이때 공정 압력을 변수로 RF power는 80W로 설정 하였으며 Ar 분압은 10mtorr, 5mtorr, 1mtorr로 각각 달리 하며 증착 하였다. 이후 전자빔 처리를 위해 각각의 시편에 Argon flow 7sccm 상태에서 DC power 3kW, RF power 300W의 세기로 전자빔 처리를 실시 하였다. 전자빔 처리에 따른 전기적, 구조적 특성을 분석하기위해 Hall measurement와 SEM, XRD, UV-vis spectroscopy을 사용하였다. 먼저 Hall measurement 측정을 통한 전기적 분석 결과 비저항이 무한대에서 약 $40m{\Omega}{\cdot}cm$로 감소된 결과를 도출 할 수 있었으며, $2{\sim}3.4{\times}10^{18}/cm^3$ 이상의 carrier density 가 측정 되었다. UV-vis spectroscopy를 이용한 투과도 측정결과 모든 시편에서 Band gap이 감소하는 결과를 보였다. SEM, XRD를 이용한 분석결과 결정성 및 grain의 크기가 증가하는 결과를 얻을 수 있었다.

• Journal of Surface Science and Engineering
• /
• v.40 no.3
• /
• pp.117-124
• /
• 2007

The ITO films were deposited on glass substrates by RF-superimposed dc reactive magnetron sputtering and were annealed in $N_2$ vacuum furnace with temperatures in the range of $403K{\sim}573K$ for 30 minutes. Electrical, optical and structural properties of ITO films were examined with varying annealing temperatures from 403 K to 573 K. The resistivity of as-deposited ITO films was $5.4{\times}10^{-4}{\Omega}cm$ at the sputter conditions of applied RF/DC power of 200/200 W, $O_{2}$ flow of 0.2 seem and Ar flow of 0.2 seem. As a result of annealing in the temperature range of $403K{\sim}573K$, the crystallization occurred at 423 K that is lower than the crystallization temperature caused by a conventional sputtering method. And the resistivity decreased from $5.4{\times}10^{-4}{\Omega}cm\;to\;2.3{\times}10^{-4}{\Omega}cm$, the carrier concentration and mobility of ITO films increased from $4.9{\times}10^{20}/cm^3\;to\;6.4{\times}10^{20}/cm^3$, from $20.4cm^2/Vsec\;to\;41.0cm^2/Vsec$, respectively. The transmittance of ITO films in visible became higher than 90% when annealed in the temperature range of $423K{\sim}573K$. High quality ITO thin films made by RF-superimposed dc reactive magnetron sputtering and annealing in $N_2$ vacuum furnace will be applied to transparent conductive oxides of the advanced flat panel display.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.160-163
• /
• 2002

Silica waveguide for an integrated diffractive optical head system was designed and fabricated. The waveguide was designed to optimize the optical efficiency of red and/or blue laser source, and a lab-made RF magnetron sputter was adopted to deposit silica cladding and core layers on SiO$_2$/Si substrates. The cladding and core layers were formed using commercial targets, and the former was done with ＃7740 and the latter with BK7 and BAK4, respectively The surface roughness of the waveguide layers was measured to be 30.3${\AA}$ for BK7 and 17.8${\AA}$ for BAK4, and the difference of refractive indices between core and cladding layers was 0.9% and 2.5%, respectively. The waveguide fabricated with the core layer of BK7 showed better optical properties when the final diffractive optical probe heads were measured with red laser(650nm) source.