• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.2
• /
• pp.86-92
• /
• 1998

In this paper, it is derived the system design parameters for the J-STD-018 of the PCS mobile station(MS) minimum performance using DS/CDMA analyzed the system performance due to the receiver components. The simulation shows the selectivity is -70.96dB at 1.25MHz frequency offset from the carrier frequency while the MS noise figure to satisfy J-STD-018 is 10dB and the input 3rd harmonics intercept point of the MS class I and MS class II-V is -9.5dBm and -14dBm respectively. When the interference power level at the receiver is small, the receiver has better performance as we increase the gain of LNA. However, when the interference level at the receiver is large, the receiver performance is decreased by the effect of the spurious. Thus, the effectiveness of LNA On/Off switching technique is proved as to reduce the effect of the spurious.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.10
• /
• pp.994-1000
• /
• 2013

Conventional MIMO system is required to a number of RF chains as much as a number of antennas. If the number of antennas increased then the number of RF chains increased. Therefore, it is difficult to apply conventional MIMO system to mobile terminals with limited power. In this paper, we propose a TDM(time division multiplexing)-based single RF chain MIMO system. The outcome shows that performance of the proposed system is similar to conventional MIMO system using multiple RF chains when STO is corrected by phase angle estimation and the synchronizing signal of received signal. Therefore, it is possible to implement the MIMO-OFDM system of low power and complexity through a single RF chain.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.539-542
• /
• 2005

In this paper, we propose a wireless data access system, which used direct sequence spread spectrum method and the ISM band with 900MHz radio frequency. By applying bi-directional transmission between wireless transmitter and receiver, it can be effectively connected with any kinds of RF-ID with 900MHz ISM band. Therefore it could economically be used as peripheral equipments for RF-ID system.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.1
• /
• pp.21-24
• /
• 2019

In this paper, 5.8GHz 25W microwave wireless power transmission system was developed. The transmission system is composed of a signal generator, a 1W drive amplifier, a 25W power amplifier, and a circularly polarized transmission antenna. The receiving system was fabricated with an integrated receiver that combines a circularly polarized receiving antenna, a pass band filter, and an RF-DC converter. And a multi-integrated receiver had twelve parts, including an integrated receiver. Under the conditions, voltage and current were measured for the system at 5cm intervals from a minimum distance of 5cm to a maximum distance of 80cm. The power was calculated for the system. The results of the system are shown in tables and graphs. The power decreases with distance, but the power does not drop sharply due to a multi-integrated receiver.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2014.06a
• /
• pp.103-104
• /
• 2014

Wide Area Differential GNSS(WA-DGNSS) was developed in order to improve the accuracy and integrity performance of GNSS. In Korea, WA-DGNSS development project, which aims to develop core algorithms and verify the performance using pseudolite-based demo system, is currently in progress. In this paper, overall structure of developed system and experimental methods which enables the post-processing test with commercial receiver will be described. In this system, pseudolite is used to broadcast augmenting signal and RF signal logger and broadcaster were used to test the performance. Performance test was conducted broadcasting the logged RF signal and pseudolite signal to commercial receiver and those results will be described.

• Journal of the Korea Convergence Society
• /
• v.8 no.11
• /
• pp.85-91
• /
• 2017

This paper concerns the design of a matching module system enabling the RF signal to be harmonized between the new base stations (RRH) and the repeater in the same frequency band of the asynchronous transfer network. This matching system controls the RF Gain Control of the module while monitoring the quality of the quality. Additionally, the RF environment has been adapted accordingly to adjust the RF Gain Control to match the receiver characteristics of the relay. As a result of this study, we improved the quality of the interface between the new base stations and existing relays.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.353-356
• /
• 2011

A Signal Receiving system to collect and analyze RF signals should be verified under simulated RF signal environment prior to verification on operation in fields and tested by using simulated RF signals in order to estimate its electrical performance. Generally, typical Signal Receiving system can measure, analyze frequency, pulse modulation, scan modulation, phase modulation on pulse, frequency modulation on pulse etc on RF signals. These RF signals should be generated from simulated RF sources in laboratory. Also the simultaneous RF signals should be simulated on laboratory. This paper describes the results of studying effective simulated RF signal source generation, the methods of the precise RF test signal generation in consideration of operational scenario.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.176-181
• /
• 2013

This paper presents a CMOS impulse radio ultra-wideband (IR-UWB) receiver implemented using IBM 0.13um CMOS technology for inner/inter-chip wireless interconnection. The IR-UWB receiver is based on the non-coherent architecture which removes the complexity of RF architecture (such as DLL or PLL) and reduces power consumption. The receiver consists of three blocks: a low noise amplifier (LNA) with active balun, a correlator, and a comparator. Simulation results show the die area of the IR-UWB receiver of 0.2mm2, a power gain (S21) of 12.5dB, a noise figure (NF) of 3.05dB, an input return loss (S11) of less than -16.5dB, a conversion gain of 18dB, a NFDSB of 22. The receiver exhibits a third order intercept point (IIP3) of -1.3dBm and consumes 22.9mW of power on the 1.4V power supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.7
• /
• pp.730-735
• /
• 2004

This paper describes what brings about DC offset and the impact or the DC offset on the performance or direct-conversion mobile receiver in WCDMA system. The performance degradation of $E_{b}/N_{o}$ due to the DC offset is presented through simulation result. Direct-conversion RF Transceiver which has the function of DC offset control is implemented and then applied to the WCDMA test-bed for the performance evaluation. The receiver performance degradation of $E_{c}/I_{o}$ is evaluated and analyzed by varying DC offset value. The practical test showed the minimum requirement of DC offset value to meet system performance.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.5
• /
• pp.595-604
• /
• 2016

Utilizing a standard 130-nm CMOS process, a RF frontend is designed at 24 GHz for automotive collision avoidance radar application. Single IF direct conversion receiver (DCR) architecture is adopted to achieve high integration level and to alleviate the DCR problem. The proposed frontend is composed of a two-stage LNA and downconversion mixers. To save power consumption, and to enhance gain and linearity, stacked NMOS-PMOS $g_m$-boosting technique is employed in the design of LNA as the first stage. The switch transistors in the mixing stage are biased in subthreshold region to achieve low power consumption. The single balanced mixer is designed in PMOS transistors and is also realized based on the well-known folded architecture to increase voltage headroom. This frontend circuit features enhancement in gain, linearity, and power dissipation. The proposed circuit showed a maximum conversion gain of 19.6 dB and noise figure of 3 dB at the operation frequency. It also showed input and output return losses of less than -10 dB within bandwidth. Furthermore, the port-to-port isolation illustrated excellent characteristic between two ports. This frontend showed the third-order input intercept point (IIP3) of 3 dBm for the whole circuit with power dissipation of 6.5 mW from a 1.5 V supply.