• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.6
• /
• pp.553-561
• /
• 2011

A theoretical approach is carried out to predict the quality factors of flexible modes of a microcantilever on a squeeze-film. The frequency response function of an inertially-excited microcantilever beam is derived using an Euler-Bernoulli beam theory. The external force due to squeeze-film phenomenon is developed from the Reynolds equation. Slip boundary conditions are employed at the interfaces between the fluid and the structure to consider the gas rarefaction effect, and pressure boundary condition at both ends of fluid analysis region is enhanced to increase the exactness of predicted quality factors. To the end, an approximate equation is derived for the first bending mode of the microcantilever. Using the approximate equation, the quality factors of the second and third bending modes are calculated and compared with experimental results of previously reported work. The comparison shows the feasibility of the current approach.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.771-778
• /
• 2006

Before the Flap type GATE is introduced until, the Turnstile type GATE was plentifully used. The Turnstile type GATE is used plentifully from the Seoul metro, Busan Transportation Corporation and Korea Railroad Corporation. From the Turnstile type GATE, the micro switch breakdown is occurred by the contact of the micro switch which perceives a Turnstile rotation and the cam. The breakdown is cause of the passenger inconveniently. In order to prevent the breakdown which is caused by Micro switch contact, Microswitch support used the sensor in Turnstile rotation perception. The sensor which is used in test is Photo Sensor and Reed Sensor two type. The test result Reed Sensor was suitable in underground environment. When using the RF card, RF card processing came to be quick

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2395-2397
• /
• 2005

A low voltage operated piezoelectric RF MEMS in-line switch has been realized by using silicon bulk micromachining technologies for advanced mobile/wireless applications. The developed RF MEMS in-line switches were comprised of four piezoelectric cantilever actuators with an Au contact metal electrode and a suspended Au signal transmission line above the silicon substrate. The measured operation dc bias voltages were ranged from 2.5 to 4 volts by varying the thickness and the length of the piezoelectric cantilever actuators, which are well agreed with the simulation results. The measured isolation and insertion loss of the switch with series configuration were -43dB and -0.21dB (including parasitic effects of the silicon substrate) at a frequency of 2GHz and an actuation voltage of 3 volts.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.8 s.185
• /
• pp.163-170
• /
• 2006

By removing sacrificial layer through ashing process, movable MEMS structure on substrate can be fabricated in surface micromachining. However, MEMS structure includes, during the ashing process, the warping or buckling effects due to stress gradient along the vertical direction of thin film. In this study, we presented method for counteracting the unwanted deflection of MEMS structure and designed using character of deposit process to overcome limited design conditions. Unit cell patterns were designed with character of deposit shape, and their final shapes were adopted using Finite Element Method. Finally, RF MEMS switch was fabricated by surface micro machining as test vehicles. We checked out that alleviation effect for deformation of switch improved by 35%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.8
• /
• pp.880-885
• /
• 2010

In this paper, we propose a reconfigurable beam steering antenna using a dipole and a loop. The radiation patterns of the two antennas were cancelled or compensated, and head for the specific direction when a dipole and a loop antenna are combined at the reasonable ratio. The structure of the antenna is very simple and planar. By changing on/ off states of switches, the proposed antenna can steer the beam direction in the x-y plane. Simulation results confirmed the steering characteristic by using two imaginary switches. The proposed antenna can change the direction of the maximum gain in the x-y plane($0^{\circ}$, ${\pm}50^{\circ}$). The proposed antenna operates in 2.5~2.56 GHz(VSWR<2). It showed that peak gain of the antenna is 1.96~2.48 dBi and overall beam width of the reconfigurable antenna covers about $125^{\circ}$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.1
• /
• pp.91-99
• /
• 2018

This paper has proposed a low-noise and high-linear RF receiver supporting TV white space from 470 MHz to 698 MHz), which is implemented in $0.13-{\mu}m$ CMOS technology. It consists of a low-noise amplifier, a RF band-pass filter, a RF amplifier, a passive down-conversion mixer, and a channel-selection low-pass filter. A low-noise amplifier and RF amplifier provide a high voltage gain to improve the sensitivity level. To suppress strong and nearby interferers, two RF filtering schemes have been performed by using a RF BPF and a down-conversion mixer. The proposed LPF has been based on the common-gate topology and adopted a bi-quad cell to achieve -24dB/oct characteristics. In addition, the RF receiver can support the overall TV band by controlling a LO frequency. The simulated results show a voltage gain of 56 dB, a noise figure of less than 2 dB, and an out-of-channel IIP3 of -2.3 dBm. It consumes 37 mA from a 1.5 V supply voltage.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1509_1510
• /
• 2009

This paper presents the design and simulation results of ohmic contact RF MEMS silicon switch with a high isolation at high frequencies along with the position of a contact part, initial off-state and intermediate off-state including the state where a contact part is placed right over a signal line of coplanar waveguide (CPW). The ohmic contact part is connected with comb drives made of high resistivity single crystalline silicon. The released contact part is $30{\mu}m$ apart from the edge of signal line on the glass substrate along the lateral direction (x-direction) at initial off-state. The electrostatic force of the comb electrode creates the x-directional movement thus initial state is converted to the intermediate off-state. The initial off-state of the switch results in isolations of -31 dB, -24 dB and reflections of -0.45 dB, -0.67 dB at 50 GHz and 110 GHz, respectively. It shows the isolation degradation when the contact part moves right over the signal line of CPW like an initial off-state of a conventional MEMS switch. The isolations and reflections are -31 dB, -24 dB and -0.50 dB, -1.31 dB at 50 GHz and 110 GHz, respectively at the intermediate off-state.

• Korean Journal of Optics and Photonics
• /
• v.14 no.4
• /
• pp.466-472
• /
• 2003

In this paper, we proposed an optical true time-delay (TTD) feeder system for phased array antennas (PAAs). The system possesses high-speed beam scan capability since, in this scheme, different lengths of fiber delay-lines are selected by optical 2${\times}$2 MEMS switches at high speed. An optical TTD capable of beam scanning in one of eight different directions has been built for 10 GHz linear PAA systems. Experimental results on time delay measurements show that the maximum time delay error is less than 0.2 ps corresponding to a scan angle error of less than 0.84o. We have also designed a 10 GHz linear PAA composed of eight micro-strip patch antenna elements driven by the proposed TTD, and the radiation patterns of this PAA have been analyzed by simulation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.93-100
• /
• 2009

This paper presents a step up four channel DC-DC converter using charge pump voltage doubler structure. Our goal is to design and implement DC-DC converter for capacitive SP4T RF MEMS switch in front end module in wireless transceiver system. Charge pump structure is small and consume low power 3.3V input voltage is boosted by DC-DC Converter to $11.3{\pm}0.1V$, $12.4{\pm}0.1V$, $14.1{\pm}0.2V$ output voltage With 10MHz switching frequency. By using voltage level shifter structure, output of DC-DC converter is selected by 3.3V four channel selection signals and transferred to capacitive MEMS devices. External passive devices are not used for driving DC-DC converter. The total chip area is $2.8{\times}2.1mm^2$ including pads and the power consumption is 7.52mW, 7.82mW, 8.61mW.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.12
• /
• pp.1113-1119
• /
• 2013

In this letter, a new approach is proposed for the design of a multi antenna for MIMO wireless devices. The proposed antenna covers various LTE(Long Term Evolution) service bands: band 17(704~746 MHz), band 13(746~787 MHz), band 5(824~894 MHz), and band 8(880~960 MHz). The proposed main antenna consists of a conventional monopole antenna with an inverted L-shaped slit for wideband operation. The proposed the LTE sub antenna is based on a switch loaded loop antenna structure, with a resonance frequency that can be controlled by capacitance of a logic circuit. The tuning technique for the LTE Rx antenna uses a RF MEMS(Micro-Electro mechanical system) to match the impedances to realize the bands of interest. Because the two proposed antennas are polarized orthogonally to each other, the ECC(Envelope Correlation Coefficient) characteristic between two antennas was measured to be very low (below 0.06) with an isolation characteristic below -20 dB between the two antennas in the operating overall LTE bands. The proposed antenna is particularly attractive for mobile devices that integrate LTE multiple systems.