• Nuclear Engineering and Technology
• /
• v.55 no.4
• /
• pp.1448-1459
• /
• 2023

A key element of the safety analysis is Loss of Coolant Analysis (LOCA) which must be performed using system thermal-hydraulic codes. These codes are extensively validated against separate effect and integral experiments. RELAP/SCDAPSIM is one such code that may be used to predict LBLOCA response in a CANDU reactor. The RD-14M experiment selected for the Best Estimate Plus Uncertainty study is a 44 mm (22.7%) inlet header break test with no Emergency Coolant Injection. This work has two objectives first is to simulate pipe break with RELAP and compare these results to those available from experiment and from comparable TRACE calculations. The second objective is to quantify uncertainty in the fuel element sheath (FES) temperature arising from model coefficient as well as input parameter uncertainties using Integrated Uncertainty Analysis package. RELAP calculated results are found to be in good agreement with those of TRACE and with those of experiments. The base case maximum FES temperature is 335.5 ℃ while that of 95% confidence 95^th percentile is 407.41 ℃ for the first order Wilk's formula. The experimental measurements fall within the predicted band and the trends and sensitivities are similar to those reported for the TRACE code.

• Nuclear Engineering and Technology
• /
• v.35 no.5
• /
• pp.426-441
• /
• 2003

A reactor inlet header break experiment, B9401, performed in the RD-14M multi channel test facility was analyzed using RELAP5/MOD3.2 and RELAP5/CANDU[1]. The RELAP5 has been developed for the use in the analysis of the transient behavior of the pressurized water reactor. A recent study showed that the RELAP5 could be feasible even for the simulation of the thermal hydraulic behavior of CANDU reactors. However, some deficiencies in the prediction of fuel sheath temperature and transient behavior in athe headers were identified in the RELAP5 assessments. The RELAP5/CANDU has been developing to resolve the deficiencies in the RELAP5 and to improve the predictability of the thermal-hydraulic behaviors of the CANDU reactors. In the RELAP5/CANDU, critical heat flux model, horizontal flow regime map, heat transfer model in horizontal channel, etc. were modified or added to the RELAP5/MOD3.2. This study aims to identify the applicability of both codes, in particular, in the multi-channel simulation of the CANDU reactors. The RELAP5/MOD3.2 and the RELAP5/CANDU analyses demonstrate the code's capability to predict reasonably the major phenomena occurred during the transient. The thermal-hydraulic behaviors of both codes are almost identical, however, the RELAP5/CANDU predicts better the heater sheath temperature than the RELAP5/MOD3.2. Pressure differences between headers govern the flow characteristics through the heated sections, particularly after the ECI. In determining header pressure, there are many uncertainties arisen from the complicated effects including steady state pressure distribution. Therefore, it would be concluded that further works are required to reduce these uncertainties, and consequently predict appropriately thermal-hydraulic behaviors in the reactor coolant system during LOCA analyses.

• Journal of the Korean Wood Science and Technology
• /
• v.12 no.1
• /
• pp.31-37
• /
• 1984

For the modification of kiln drying schedule, relations between resistance to drying Rd and the moisture content or drying times were found for 4/4, 6/4 and 8/4 green Douglas fir heartwood by the mild drying schedule and the severe drying schedule until the average moisture content was about 10 percent. The results of this study were as follows. 1. Resistance to drying of thicker lumber was higher than that of thinner lumber and resistance to drying of three different thicknesses were negligible between the mild-and the severe drying schedule. The relationships between resistance to drying and two schedules or three thicknesses of lumber were $Rd_1=1.830{\times}10^5\;M^{-2.24}$ for 4/4 lumber by the mild drying schedule, $Rd_2=1.822{\times}10^5\;M^{-2.25}$ for 4/4 lumber by the severe drying schedule, $Rd_3=2.352{\times}10^5\;M^{-2.14}$ for 6/4 lumber by the mild drying schedule, $Rd_4=3.457{\times}10^5\;M^{-2.27}$ for 6/4 lumber by the severe drying schedule, $Rd_5=1.317{\times}10^6\;M^{-2.56}$ for 8/4 lumber by the mild drying schedule, $Rd_6=8.267{\times}10^5\;M^{-2.40}$ for 8/4 lumber by the severe drying schedule. 2. Thinner lumber exhibited lower level of moisture content and shorter drying time required at intersection point between the moisture content and resistance to drying as a function of drying time than those of thicker lumber. Drying time of mild drying was longer than that of severe drying and similar to the level of moisture content at intersection point.

• Rapid Communication in Photoscience
• /
• v.3 no.1
• /
• pp.16-19
• /
• 2014

Anodic self-organized titania nanotube (TNT) arrays have a great potential as efficient electron-transport materials for dye-sensitized solar cells (DSSC). Herewith we report the photovoltaic and kinetic investigations for a series of heteroleptic ruthenium complexes (RD16-RD18) sensitized on TNT films for DSSC applications. We found that the RD16 device had an enhanced short-circuit current density ($J_{SC}/mAcm^{-2}=15.0$) and an efficiency of power conversion (${\eta}=7.2%$) greater than that of a N719 device (${\eta}=7.1%$) due to the increasing light-harvesting and the broadened spectral features with thiophene-based ligands. However, the device made of RD17 (adding one more hexyl chain) showed smaller $J_{SC}(14.1mAcm^{-2})$ and poorer ${\eta}(6.8%)$ compare to those of RD16 due to smaller amount of dye-loading and less efficient electron injection for the RD17 device than for the RD16 device. For the RD18 dye (adding one more thiophene unit and one more hexyl chain), we found that the device showed even lower $J_{SC}(13.2mAcm^{-2}) $ that led to a poorest device performance (${\eta}=6.2%$) for the RD18 device. These results are against to those obtained from the same dyes sensitized on $TiO_2$ nanoparticle films and they can be rationalized according to the electron transport kinetics measured using the methods of charge extraction and transient photovoltage decays.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.20 no.1
• /
• pp.53-62
• /
• 1990

This experiment was performed to clarify the effects of /sup 60/Co gamma irradiation on secretory function, amylase activity and contents of nucleic acids of parotid gland in rat. Experimental animals were divided into 6th hours, 3rd, 7th, 14th and 28th days after irradiation and control. The experimental animals are singly irradiated with 20Gy (2,000rad) through protective lead block. Secretory function of parotid gland was evaluted by uptake and clearance of /sup 99m/TcO₄. /sup 99m/TcO₄. 0.2μ ci/gm, was injected into peritonium in uptake groups. Rats were sacrified with cervical dislocation after 30 minutes and gland was excised. In the clearance group. pilocarpine nitrate (8㎎/㎏) was intraperitoneally injected at 30 minutes after /sup 99m/TcO₄ injection and rats were sacrified 30 minutes after pilocarpine injection. Radioactivity of excised parotid gland was measured by using of gamma counter and stimulation-secretion coefficients, uptake radioactivity divided by clearance radioactivity, was calculated. Amylase activity and contents of DNA and RNA were determined by spectrophotometry. The results obtained were as follows: 1. In the uptake test, the radioactivity of /sup 99m/TcO₄ per unit weight increase in experimental group except 6th hours group, compared with control groups and showed a peak at 3rd days after irradiation. 2. In the clearance test, the radioactivity of /sup 99m/cO₄per unit weight rose to a peak at 3rd days after irradiation and gradually recovered thereafter. 3. Stimulation-secretion coefficient of parotid gland decreased at 6th hours, 3rd and 7th days after irradiation, and gradually increased. 4. Amylase activity of parotid gland decreased in 3rd and 7th days group, and especially lowest in 3rd days after irradiation. 5. The contents of DNA showed no definite difference in all the experimental groups, but RNA was seemed to decrease with time after irradiation.

• Journal of Microbiology and Biotechnology
• /
• v.22 no.3
• /
• pp.343-351
• /
• 2012

In this paper, the kinetics of a cloned special glucosidase, named ginsenosidase type III hydrolyzing 3-O-glucoside of multi-protopanaxadiol (PPD)-type ginsenosides, were investigated. The gene (bgpA) encoding this enzyme was cloned from a Terrabacter ginsenosidimutans strain and then expressed in E. coli cells. Ginsenosidase type III was able to hydrolyze 3-O-glucoside of multi-PPD-type ginsenosides. For instance, it was able to hydrolyze the 3-O-${\beta}$-D-(1${\rightarrow}$2)-glucopyranosyl of Rb1 to gypenoside XVII, and then to further hydrolyze the 3-O-${\beta}$-D-glucopyranosyl of gypenoside XVII to gypenoside LXXV. Similarly, the enzyme could hydrolyze the glucopyranosyls linked to the 3-O-position of Rb2, Rc, Rd, Rb3, and Rg3. With a larger enzyme reaction $K_m$ value, there was a slower enzyme reaction speed; and the larger the enzyme reaction $V_{max}$ value, the faster the enzyme reaction speed was. The $K_m$ values from small to large were 3.85 mM for Rc, 4.08 mM for Rb1, 8.85 mM for Rb3, 9.09 mM for Rb2, 9.70 mM for Rg3(S), 11.4 mM for Rd and 12.9 mM for F2; and $V_{max}$ value from large to small was 23.2 mM/h for Rc, 16.6 mM/h for Rb1, 14.6 mM/h for Rb3, 14.3 mM/h for Rb2, 1.81mM/h for Rg3(S), 1.40 mM/h for Rd, and 0.41 mM/h for F2. According to the $V_{max}$ and $K_m$ values of the ginsenosidase type III, the hydrolysis speed of these substrates by the enzyme was Rc>Rb1>Rb3>Rb2>Rg3(S)>Rd>F2 in order.

• Journal of Microbiology
• /
• v.41 no.3
• /
• pp.202-206
• /
• 2003

A protein, exhibiting a high similarity to the major serine transporter of Escherichia coli, SstT, was found in Haemophilus influenzae Rd. A Na$\^$＋/-stimulated serine transport activity was also detected in the cells. The gene (sstT) for the Na$\^$＋//serine symporter from the chromosome of H. influenzae was cloned, and the properties of the transporter investigated. The serine transport activity was stimulated by Na$\^$＋/. The uptake of Na$\^$＋/ was elicited by the addition of serine or threonine into the cells, supporting the idea that these amino acids are transported by a mechanism of Na$\^$＋//substrate symport. No uptake of H$\^$＋/ was elicited by the influx of serine. The serine transport via the SstT of H. influenzae was inhibited by excess threonine, which was used as another substrate. The $K_{m}$ and the $V_{max}$ values for the serine transport were 2.5 ${\mu}$M and 14 nmol/min/mg protein, respectively.

• Imaging Science in Dentistry
• /
• v.33 no.3
• /
• pp.179-185
• /
• 2003

Purpose: To investigate the effects of irradiation on the phenotypic expression of the MC3T3-El osteoblastic cell line, particularly on the expression of osteocalcin and osteopontin. Materials and Methods: Cells were irradiated with a single dose of 0.5, 1,4, and 8 Gy at a dose rate of 5.38 Gy/min using a cesium 137 irradiator. After the specimens were harvested, RNA was extracted on the 3rd, 7th, 14th, and 21st day after irradiation. The RNA strands were reverse-transcribed and the resulting cDNAs were subjected to amplification by PCR. Results: The irradiated cells demonstrated a dose-dependent increase in osteocalcin and a dose-dependent decrease in osteopontin mRNA expression compared with the non-irradiated control group, The amount of osteocalcin mRNA expression decreased significantly at the 3rd day after irradiation of 0,5, 1,4, and 8 Gy, and also decreased significantly at the 3rd, 14th, and 21 st day after irradiation in the 8 Gy exposed group compared with the control group, The degree of osteopontin mRNA expression increased significantly at the 7th day after irradiation of 0,5, 1,4, and 8Gy, Conclusion: These results showed that each single dose of 0,5, 1, 4, and 8 Gy influenced the mRNA expression of osteocalcin and osteopontin associated with the calcification stage of osteoblastic cells, suggesting that each single dose affected bone formation at the cell level.

• Journal of Technologic Dentistry
• /
• v.41 no.2
• /
• pp.63-69
• /
• 2019

Purpose: The purpose of this study is to evaluate the effect of CAD/CAM system milling tool wear on the marginal and internal fit of PMMA implant interim prosthesis three-dimensional manner. Methods: A total of 20 crowns were fabricated with CAD/CAM method. Their designs were unified to first molar of the left maxilla. The Customized abutments were prepared and scanned with on optical model scanner. Five crowns were milled by the newly replaced tool (1st milling), and 15 crowns were milled by 2nd, 3rd, 4th milling tool. The marginal and internal fit of 20 interim crowns were measured using the triple-scan protocol. Results: Statistically significant difference was found between the $1^{st}$ milling group ($51.8{\pm}14.6{\mu}m$) and the $3^{rd}$, $4^{th}$ milling group ($128.6{\pm}43.8{\mu}m$, $146.2{\pm}38.1{\mu}m$, respectively) at the distal margins. In the mesial margins, There was a statistically significant difference between the $1^{st}$ milling group ($63.6{\pm}25.9{\mu}m$) and the $3^{rd}$, $4^{th}$ milling group ($137.2{\pm}25.9{\mu}m$, $186.8{\pm}70.6{\mu}m$, respectively). In the distal line angle, significant difference was found between the $1^{st}$, $2^{nd}$, $3^{rd}$ milling groups and the $4^{th}$ milling group. In the mesial axial wall, significant difference was found between the $1^{st}$ milling group ($52.2{\pm}20.3{\mu}m$) and the $3^{rd}$, $4^{th}$ milling groups ($22.8{\pm}8.8{\mu}m$, $7.8{\pm}5.7{\mu}m$). Conclusion: As a result of the experiment, decrease of the marginal and internal fit was statistically significant as the number of machining cycles increased. In order to produce clinically excellent restorations, it is recommandable to consider the condition of the milling tool wear, when designing the restoration with CAD program.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.12
• /
• pp.14-24
• /
• 2001

An active MMIC L-band down converting mixer was designed by using GaAs FET with 0.5 ${\mu}$m gate length and 300 ${\mu}$m gate width. Main circuit topology was cascoded two active FETs. It consumed only 7.5 mA with 3V DC voltage supply. Conversion gain of 6.63 dB, minumium noise figure of 5.06 dB and Input $3^{rd}$ Order Intercept Point of 6.4 dBm were obtained. The chip size is 1.86 mm ${\times}$ 1.28 mm.