• Korean Journal of Food Science and Technology
• /
• v.45 no.5
• /
• pp.531-536
• /
• 2013

We developed a simple, sensitive, and specific analytical method for prometryn using gas chromatography-mass spectrometry (GC-MS). Prometryn is a selective herbicide used for the control of annual grasses and broadleaf weeds in cotton and celery crops. On the basis of high specificity, sensitivity, and reproducibility, combined with simple analytical operation, we propose that our newly developed method is suitable for use as a Ministry of Food and Drug Safety (MFDS, Korea) official method in the routine analysis of individual pesticide residues. Further, the method is applicable in clams. The separation condition for GC-MS was optimized by using a DB-5MS capillary column ($30m{\times}0.25mm$, 0.25 ${\mu}m$) with helium as the carrier gas, at a flow rate of 0.9 mL/min. We achieved high linearity over the concentration range 0.02-0.5 mg/L (correlation coefficient, $r^2$ >0.998). Our method is specific and sensitive, and has a quantitation limit of 0.04 mg/kg. The average recovery in clams ranged from 84.0% to 98.0%. The reproducibility of measurements expressed as the coefficient of variation (CV%) ranged from 3.0% to 7.1%. Our analytical procedure showed high accuracy and acceptable sensitivity regarding the analytical requirements for prometryn in fishery products. Finally, we successfully applied our method to the determination of residue levels in fishery products, and showed that none of the analyzed samples contained detectable amounts of residues.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.2
• /
• pp.515-527
• /
• 2014

This study conducted experiment for understanding engineering characteristics of domestic sands by examining standard sand and sand from Yokji Island and Nakdong River in terms of confining pressure, $K_0$, over consolidation and relative density factors through triaxial compression test. The test showed that deviator stress by strain positively changed as confining pressure and relative density grow while $K_0$ and over consolidation factors do not directly correlated with it. Angle of internal friction decreases as confining pressure increases which strengthens contact force between particles, and declines as relative density drops, whereas $K_0$ and over consolidation factors hardly affect the results. When it comes to volumetric strain, volume expansion decreases as confining pressure increase due to crushability and rearrangement of particles while $K_0$ and over consolidation shows same movement unconditionally, and relative density appears compressed as it grows at the beginning however it expands as axial strain increases. Modulus of elasticity ($E_{sec}$) by strain has tendency into convergence resulting in initial secant modulus of elasticity ($E_{ini}$) > secant modulus of elasticity($E_{sec}$) > tangent modulus of elasticity ($E_{tan}$). On the other hand, it grows as confining pressure and relative density increase while indicating similar modulus of elasticity ($E_{sec}$) regarding on $K_0$ and over consolidation. Slope of critical line (M) tended to decrease as confining pressure increases, follow same line according to $K_0$, confining pressure and relative density, and increase as relative density grows.

• Korean Journal of Environmental Biology
• /
• v.29 no.3
• /
• pp.162-170
• /
• 2011

In order to assess the inorganic and organic pollutents characteristics in marine water, we investigated COD (Chemical Oxygen Demand), Chlorophyll a and Escherichia coli during four seasons at 20 stations of Gwangyang Bay and at 23 stations of Jinhae Bay, Korea. The bay is divided into three zones in Gwangyang and four zones in Jinhae respectively, based on the pollutent levels. In Gwangyang Bay, the high concentration (mean 4.7 mg $L^{-1)$) of COD was recorded during spring season at Zone I, which can be characterized as a semi-enclosed eutrophic area (St. 1~9). Also, Chl. a concentrations were high at Zone I (mean 14.0 ${\mu}g\;L^{-1}$). The colony of E. coli were detected during summer season at Zone II, which is influenced by Seomjin River water. The E. coli may have been entered from the river water in a large pulse during rainy season. On the other hand, E. coli was kept low levels during four seasons at the Zone III, which is influenced indirectly by surface water currents from offshore of the bay. In Jinhae Bay, the high COD and Chl. a were shown during all seasons at Zone I, which is characteristed by semi-enclosed eutrophic area of Masan and Haengam bays. The Zone I also had been shown relatively high E. coli concentration in all seasons. In constrast, other three zones did not show seasonal characteristics of the E. coli concentrations. The present study suggests that E. coli concentrations can be significantly elevated in eutrophic semi-enclosed area.

• Korean Journal of Poultry Science
• /
• v.38 no.4
• /
• pp.293-304
• /
• 2011

The current work was carried out to investigate the effect of crossbred Korean native chickens (KNC) on performance and meat quality. A total of 720 chicks (1d of age) was used in this work and were divided into groups by crossbreds (A, B, C and D) and sex (male and female). Crossbreds were A) (KNC egg-meat type C strains ${\times}$ KNC meat type S strains) ${\times}$ Ross broiler, B) (KNC egg-meat type C strains ${\times}$ KNC meat type H strains) ${\times}$ KNC meat type S strains, C) (KNC native R strains${\times}$KNC meat type S strains)${\times}$KNC meat type H strains and D(White Semibroiler Chickens). Experimental diets consisted of 3 phases such as starter (0~5 weeks; CP 20.0%, ME 3,050 kcal/kg), earlier (5~8 weeks; CP 18.0%, ME 3,100 kcal/kg) and finisher (8~12 weeks; CP 16.0%, ME 3,150 kcal/kg). They were fed the broiler diets for 12 weeks at the flat house and thirty six chickens were slaughtered at week 5 and 10. There was no significant difference on the fertility of crossbred KNCs, and the hatchability of B crossbred was low compared to other crossbreds. On body weight (BW), D crossbred resulted in a higher BW after 5 weeks (P<0.05). Body weight gain (BWG) and feed intake (FI) of A crossbred were also significant higher compared to the other crossbreds for all periods. On carcass ratio (CR), A crossbred showed higher CR at 5 weeks, there was no significant among crossbreds at 10 weeks. The partial meat ratio(ala, breast, neck, leg) of C crossbred was the lowest among other crossbreds (P<0.05), but the back meat ratio was not difference among treatments at 5 and 10 weeks. pH of meats have no difference among crossbreds at 5 week, and A crossbred was high compared to other crossbreds at 10 week (P<0.05). The moisture content of D crossbred meat and the protein content of B crossbred meat were high compared to other crossbreds at 5 week. Chemical compositions of meats have no difference among crossbreds at 10 week. Lightness and redness have not significance among crossbreds at 5 week, and redness of A crossbred was the highest among all crossbreds (P<0.05). Shear force and cooking loss of A crossbred were high at 5 week, and cooking loss of A crossbred was low compared with other crossbreds at 10 week. These results suggested the basic data that needed to develope the new strains.

• The Korean Journal of Malacology
• /
• v.29 no.4
• /
• pp.325-334
• /
• 2013

The purpose of this paper is to compare and analyze family variations for growth-related traits of Pacific abalone, Haliotis discus hannai. Genetic parameters and breeding values were estimated using all measurement data like shell length, shell width, and total weight as 18-month-old growth traits of 5,334 individuals of selected third generation's Pacific abalone produced in 2011. Family variations of 865 individuals of the upper 10 families with the largest number were inspected. Overall mean in phenotypic traits of 18-month-old Pacific abalone which was investigated in this study showed 54.5 mm of shell length, 36.8 mm of shell width and 21.3 g of total weight respectively. And, variation coefficient of total weight was 51.0%, so variability of data was shown to be higher than 21.1% of shell length and 20.7% of shell width. The family effects showed significant difference by each family (p < 0.05), and heritability of shell length, shell width, and total weight was medium with 0.370, 0.382, and 0.367 respectively. So it is considered that family selection is more advantageous than individual selection. On the basis of breeding values of estimated shell length and total weight, to investigate distribution and ranking by each individual about the upper 10 families with the largest number of individuals, the values were used by being changed into standardized breeding values. Based on shell length, it was investigated that the individual number of the upper 5.4% is 152 and the number of the lower 5.4% is 8. In case of total weight, it was inspected that the individual number of the upper 5.4% is 164 and the number of the lower 5.4% is 1. Like these, phenotypic and genetic diverse variations between families could be checked. By estimating genetic parameters and breeding values of a population for production of the next generation, if they are used properly in selection and mating, it is considered that more breeding effects can be expected.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.1
• /
• pp.82-89
• /
• 2009

Two in vitro experiments were conducted to examine the effects of propionate precursors in the dicarboxylic acid pathway on ruminal fermentatation characteristics, $CH_4$ production and degradation of feed by rumen microbes. Fumarate or malate as sodium salts (Exp. 1) or acid type (Exp. 2) were added to the culture solution (150 ml, 50% strained rumen fluid and 50% artificial saliva) to achieve final concentrations of 0, 8, 16 and 24 mM, and incubated anaerobically for 0, 1, 3, 6, 9 and 12 h at $39^{\circ}C$. For both experiments, two grams of feed consisting of 70% concentrate and 30% ground alfalfa (DM basis) were prepared in a nylon bag, and were placed in a bottle containing the culture solution. Addition of fumarate or malate in both sodium salt and acid form increased (p<0.0001) pH of culture solution at 3, 6, 9 and 12 h incubations. The pH (p<0.0001) and total volatile fatty acids (VFA, p<0.05) were enhanced by these precursors as sodium salt at 3, 6 and 9 h incubations, and pH (p<0.001) and total VFA (p<0.01) from fumarate or malate in acid form were enhanced at a late stage of fermentation (9 h and 12 h) as the addition level increased. pH was higher (p<0.001) for fumarate than for malate as sodium salt at 3 h and 6 h incubations. Propionate ($C_3$) proportion was increased (p<0.0001) but those of $C_2$ (p<0.05) and $C_4$ (p<0.01 - p<0.001) were reduced by the addition of sodium salt precursors from 3 h to 12 incubation times while both precursors in acid form enhanced (p<0.011 - p<0.0001) proportion of $C_3$ from 6h but reduced (p<0.018 - p<0.0005) $C_4$ proportion at incubation times of 1, 3, 9 and 12 h. Proportion of $C_3$ was increased (p<0.05 - p<0.0001) at all incubation times by both precursors as sodium salt while that of $C_3$ was increased (p<0.001) from 6h but $C_4$ proportion was decreased by both precursors in acid form as the addition level increased. Proportion of $C_3$ was higher (p<0.01 - p<0.001) for fumarate than malate as sodium salt from 6 h incubation but was higher for malate than fumarate in acid form at 9 h (p<0.05) and 12 h (p<0.01) incubation times. Increased levels (16 and 24 mM) of fumarate or malate as sodium salt (p<0.017) and both precursors in acid form (p<0.028) increased the total gas production, but no differences were found between precursors in both chemical types. Propionate precursors in both chemical types clearly reduced (p<0.0001 - p<0.0002) $CH_4$ production, and the reduction (p<0.001 - p<0.0001) was dose dependent as the addition level of precursors increased. The $CH_4$ generated was smaller (p<0.01 - p<0.0001) for fumarate than for malate in both chemical types. Addition of fumarate or malate as sodium type reduced (p<0.004) dry matter degradation while both precursors in both chemical types slightly increased neutral detergent fiber degradability of feed in the nylon bag.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.31 no.3
• /
• pp.243-248
• /
• 2009

Purpose: Rehabilitation of the edentulous posterior maxilla with dental implants often poses difficulty because of insufficient bone volume caused by pneumatization of the maxillary sinus and by crestal bone resorption. Sinus grafting technique was developed to increase the vertical height to overcome this problem. The present study was designed to evaluate the sinus floor augmentation with anorganic bovine bone (Bio-$cera^{TM}$) using histomorphometric and clinical measures. Patients and methods: Thirteen patients were involved in this study and underwent total 14 sinus lift procedures. Residual bone height was ${\geq}2mm$ and ${\leq}6mm$. Lateral window approach was used, with grafting using Bio-$cera^{TM}$ only(n=1) or mixed with autogenous bone from ramus and/or maxillary tuberosity(n=13). After 6 months of healing, implant sites were created with 3mm diameter trephine and biopsies taken for histomorphometric analysis. The parameters assessed were area fraction of new bone, graft material and connective tissue. Immediate and 6 months after grafting surgery, and 6 months after implantation, computed tomography (CT) was taken and the sinus graft was evaluated morphometric analysis. After implant installation at the grafted area, the clinical outcome was checked. Results: Histomorphometry was done in ten patients.Bio-$cera^{TM}$ particles were surrounded by newly formed bone. The graft particles and newly formed bone were surrounded by connective tissue including small capillaries in some fields. Imaging processing revealed $24.86{\pm}7.59%$ of new bone, $38.20{\pm}13.19%$ connective tissue, and $36.92{\pm}14.51%$ of remaining Bio-$cera^{TM}$ particles. All grafted sites received an implant, and in all cases sufficient bone height was achieved to install implants. The increase in ridge height was about $15.9{\pm}1.8mm$ immediately after operation (from 13mm to 19mm). After 6 months operation, ridge height was reduced about $11.5{\pm}13.5%$. After implant installation, average marginal bone loss after 6 months was $0.3{\pm}0.15mm$. Conclusion: Bio-$cera^{TM}$ showed new bone formation similar with Bio-$Oss^{(R)}$ histomorphometrically and appeared to be an effective bone substitute in maxillary sinus augmentation procedure with the residual bone height from 2 to 6mm.

• Journal of Korean Academy of Nursing
• /
• v.25 no.4
• /
• pp.653-667
• /
• 1995

Post - operative wound infections have been a serious problem in nursing care in the operating room and appear to be strongly related to the infection occurring during the performance of operation. The purpose of this study is to identify patterns in duration of surgical hand scrub (SHS), to evaluate the method of SHS and to examine the rate of glove perforation. Subjects for this study include 244 doctors and 169 nurses working in the operative theatre of a hospital in Seoul area. Test samples and related data were collected from this medical facility between April 1, through 15, and July 1, through 5, 1995 by the author and a staff member working in the operating room. For the study, data on the SHS of doctors and nurses were obtained at the time of operation and multiple batches of surgical gloves worn by the operating doctors were collected after each operation. The duration of SHS was measured with a stop watch and the method of SHS was evaluated according to Scoring Hand Scrub Criteria (SHS Criteria) and expressed as SHS scores. For the analysis of the data, t-test was used to compare the differences in the duration and the SHS scores of doctors and nurses, and Pearson's correlation coefficient was used to examine the relationship between the SHS duration and the SHS scores. The results of the study are summarized as follows. 1) The mean time spent in each SHS was 167 seconds in nurses, and 127 seconds in doctors. The data comparing nurses and doctors indicated that there were significant differences in Our ation of SH S between these two groups (t=5.58, p=.000). 2) The mean time spent in the first SHS was 145 seconds and that in the End SHS, 135 seconds, and there was not a significant difference in the duration of the SHS between doctors and nurses (t=1.44, P=.156). 3) The mean time spent in the SHS by OS (Orthopaedic surgery) doctors was 162 seconds, 150 seconds by NS(Neurologic surgery), 121 seconds by GS(General surgery), 94 seconds by OPH(Opthalmology) and DS(Dental surgery), 82 seconds by URO(Urology), 78 seconds by PS(Plastic surgery) and 40 seconds by ENT(Ear, Nose & Throat) These also showed a significant difference in the duration of the SHS among the medical specialities (t=4.8, P=.0001). 4) The average SHS score of the nurses was 15.2, while that of doctors was 13.1. The statistical analysis showed that t-value was 3.66, p was. 000. This indicates that the nurses actually clean their hands more thoroughly than the doctors do. 5) The average SHS score of NS doctors was 15.5, 15.3 for doctors for OPH,14.3 for OS,12.7 for GS, 12.0 for DS, 11.7 for URO, 10.1 for PS, 7.5 for ENT. Comparison of the average SHS scores from 8 specialties showed that there was a significant differences in the patterns of the SHS (F=5.08, P=.000) among medical specialties. 6) It appears that the operating personnel scrub the palms and dorsum of their hand relatively well, however, less thorough the nails and fingers. 7) The more the operating personnel spend their time in hand scrubbing, the more correctly they clean their hands(r=.6427, P<.001). 8) The overall frequencies of perforation in all post-operative gloves tested was 38 out of 389 gloves (10.3%). The perforation rate for PS was 13%, 12.1% for GS,8.8% for 05, and 3.3% for NS.

• Management & Information Systems Review
• /
• v.39 no.2
• /
• pp.39-60
• /
• 2020

Block chain technology is one of the core elements for realizing the 4^th industrial revolution, and many efforts have been made by government and companies to provide services based on block chain technology. In this study we analyzed the benefits of block chain technology for EVMS and designed EVMS block chain platform with increased data security and work efficiency for project management data, which are important assets in monitoring progress, foreseeing future events, and managing post-completion. We did the case studies on the benefits of block chain technology and then conducted the survey study on security, reliability, and efficiency of block chain technology, targeting 18 block chain experts and project developers. And then, we interviewed EVMS system operator on the compatibility between block chain technology and EVM Systems. The result of the case studies showed that block chain technology can be applied to financial, logistic, medical, and public services to simplify the insurance claim process and to improve reliability by distributing transaction data storage and applying security·encryption features. Also, our research on the characteristics and necessity of block chain technology in EVMS revealed the improvability of security, reliability, and efficiency of management and distribution of EVMS data. Finally, we designed a network model, a block structure, and a consensus algorithm model and combined them to construct a conceptual block chain model for EVM system. This study has the following contribution. First, we reviewed that the block chain technology is suitable for application in the defense sector and proposed a conceptual model. Second, the effect that can be obtained by applying block chain technology to EVMS was derived, and the possibility of improving the existing business process was derived.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.6
• /
• pp.327-340
• /
• 2017

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2016. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering have been reviewed as groups of flow, heat and mass transfer, the reduction of pollutant exhaust gas, cooling and heating, the renewable energy system and the flow around buildings. CFD schemes were used more for all research areas. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the results of the long-term performance variation of the plate-type enthalpy exchange element made of paper, design optimization of an extruded-type cooling structure for reducing the weight of LED street lights, and hot plate welding of thermoplastic elastomer packing. In the area of pool boiling and condensing, the heat transfer characteristics of a finned-tube heat exchanger in a PCM (phase change material) thermal energy storage system, influence of flow boiling heat transfer on fouling phenomenon in nanofluids, and PCM at the simultaneous charging and discharging condition were studied. In the area of industrial heat exchangers, one-dimensional flow network model and porous-media model, and R245fa in a plate-shell heat exchanger were studied. (3) Various studies were published in the categories of refrigeration cycle, alternative refrigeration/energy system, system control. In the refrigeration cycle category, subjects include mobile cold storage heat exchanger, compressor reliability, indirect refrigeration system with $CO_2$ as secondary fluid, heat pump for fuel-cell vehicle, heat recovery from hybrid drier and heat exchangers with two-port and flat tubes. In the alternative refrigeration/energy system category, subjects include membrane module for dehumidification refrigeration, desiccant-assisted low-temperature drying, regenerative evaporative cooler and ejector-assisted multi-stage evaporation. In the system control category, subjects include multi-refrigeration system control, emergency cooling of data center and variable-speed compressor control. (4) In building mechanical system research fields, fifteenth studies were reported for achieving effective design of the mechanical systems, and also for maximizing the energy efficiency of buildings. The topics of the studies included energy performance, HVAC system, ventilation, renewable energies, etc. Proposed designs, performance tests using numerical methods and experiments provide useful information and key data which could be help for improving the energy efficiency of the buildings. (5) The field of architectural environment was mostly focused on indoor environment and building energy. The main researches of indoor environment were related to the analyses of indoor thermal environments controlled by portable cooler, the effects of outdoor wind pressure in airflow at high-rise buildings, window air tightness related to the filling piece shapes, stack effect in core type's office building and the development of a movable drawer-type light shelf with adjustable depth of the reflector. The subjects of building energy were worked on the energy consumption analysis in office building, the prediction of exit air temperature of horizontal geothermal heat exchanger, LS-SVM based modeling of hot water supply load for district heating system, the energy saving effect of ERV system using night purge control method and the effect of strengthened insulation level to the building heating and cooling load.