• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.125-129
• /
• 2008

A low-voltage active CMOS inductor approach, which can improve the quality-factor(Q), is proposed in this paper. A low-voltage active inductor circuit topology with a feedback resistance is proposed, which can substantially improve its equivalent inductance and quality-factor(Q). This proposed low-voltage active inductor with a feedback resistance was simulated by ADS(Agilent) using 0.18um standard CMOS technology. Simulation showed that the designed active inductor had a maximum quality-factor(Q) of 3000 with a 1.5nH inductance at 4GHz

• Journal of Advanced Navigation Technology
• /
• v.19 no.3
• /
• pp.244-249
• /
• 2015

High-altitude electromagnetic pulse (HEMP) is generated from a nuclear burst at high altitudes above the Earth, the electromagnetic fields reach the ground nearly simultaneously with regard to the operation time of systems. The aim of this analysis is to inquire about HEMP characteristics and to analyze about effect in orthogonal frequency division multiplexing (OFDM) system. Specifically, HEMP characteristics are classified field sources, spatial coverage, time domain behavior, frequency spectrum and field intensities in this study. Bits error rate (BER) of the receiver with the software simulation is confirmed for the HEMP effect. Q-factor made a difference about interference duration by transfer characteristics of system. When Q factor is smaller, the recovery time from HEMP interference is short. To the contrary, if the Q factor is larger, the recovery duration is lasted longer by 300-600%.

• Economic and Environmental Geology
• /
• v.27 no.6
• /
• pp.557-561
• /
• 1994

Q estimates are made by direct measurements of energy loss per cycle from primary P and S waves, as a function of frequency. Assuming that intrinsic Q is frequency independent and scattering Q is frequency dependent over the frequencies of interest, the relative contributions of each, to a total observed Q, may be estimated. Test examples are produced by computing viscoelastic synthetic seismograms using a pseudo spectral solution with inclusion of relaxation mechanisms (for intrinsic Q) and a fractal distribution of scatterers (for scattering Q). The composite theory implies that when the total Q for S-waves is smaller than that for P-waves (the usual situation), intrinsic Q is dominating; when it is larger, scattering Q is dominating. In the inverse problem, performed by a global least squares search, intrinsic $Q_p$ and $Q_s$ estimates are reliable and unique when their absolute values are sufficiently low that their effects are measurable in the data. Large $Q_p$ and $Q_s$ have no measurable effect and hence are not resolvable. Standard deviation of velocity $({\sigma})$ and scatterer size (A) are less unique as they exhibit a tradeoff as predicted by Blair's equation. For the P-waves, intrinsic and scattering contributions are of approximately the same importance, for S-waves, the intrinsic contributions dominate.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.909-916
• /
• 2005

This paper describes that the Q factor of a conventional $\lambda$/4-microstrip resonator with short load can be improved and also the problem that the serial-resonant frequency(2$f_o$) should be deviated from can be settled by the proposed $\lambda$/4-microstrip resonator, which is used to suppress the harmonics of a nonlinear circuit.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.3
• /
• pp.39-43
• /
• 2011

Effects of cavity material on the Q-factor measurement of microwave dielectric materials were studied by HFSS simulation and the measurements using metal cavity. $TE_{01\delta}$ mode resonant frequency was determined from the electric and magnetic field patterns and the loaded Q-factor was calculated from 3dB bandwidth of $S_{21}$ spectrum. When the cavity metal materials were Cu, SUS and Au cavity, the level of Q-factor was similar. However, Q-factor was significantly decreased when the cavity metal material was CuO. The Q-factor measurements of dielectric resonator by network analyzer using various metal cavity exhibits consistent behavior.

• Korean Journal of Materials Research
• /
• v.5 no.1
• /
• pp.36-41
• /
• 1995

Dielectric properties were investigated at Mn doped $(Pb_{1-x}Ca_{x})ZrO_{3}$ with x=0.38 in microwavefrequencies. Both the density and Q values of sintered ceramics increased with increasing calciningtemperature. In the sample sintered at $1300^{\circ}C$ for 2 hrs, the deped Mn ions completely solubled in $(Pb,Ca)ZrO_{3}$ phase until 0.5wt% and the grain size was independent of doping amount. It was observed thathigh dielectric constant of 90 - 100 and high quality factor of 1300 at 4 GHz for O.l5wt% Mn doped$(Pb_{0.62}Ca_{0.38})ZrO_{3}$. The Mn" and Mn" worked as acceptors in $(Pb,Ca)ZrO_{3}$ which created the oxygen vacancies and affected the increment of the Q values. However, the excess Mn doping more than 0.5wt% resulted in decreasing Q values.decreasing Q values.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.4 no.3
• /
• pp.99-105
• /
• 2000

한반도 동남부 지역에서 발생하고 관찰된 약진 또는 중진의 자료를 이영하여 이 지역의 Q값과 지진원의 특성인 모서리 주파수 (fc), 응력강하량(Δ$\delta$) 및 모멘크규모 (Mw)를 산정하였다. 가속도 스펙트럼의 경사와 관련된 x의 통계학적 분포로부터 추정한 Q의 95% 신뢰범위는 1656~2454 이다. 1998년 1월 18일 울산 앞바다 지진과 1997년 6월 26일 경주지진의 지진원 요소를 구한 결과 fc 는 각각 4.22Hz , 2.94Hz, Δ$\delta$는 각각 106.8 bar, 106.2 bar, Mw는 각각 3.9, 4.0으로 추정되었다. 제한된 자료수로 인하여 이들의 통계학적 성질을 충분히 규명하지는 못하였지만 다른 연구자들의 기존결과와 유사한 값을 보인다. 본 연구의 결과는 강진동 모사에 직접 이용이 가능하며, 이 지역에 위치한 원자력 발전소 내진 안전성 검토에도 이용될 수 있다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.5B
• /
• pp.985-991
• /
• 2000

In this paper, the optimum structure of 2GHz magnetic thin film planar inductor were designed and fabricated to reduce the inductor area and to maximize the inductance L and quality factor Q of the inductor. The optimum design was performed utilizing Co90Fe10 layer multilayered with SiO2 layers to avoid the eddy-current skin effect and considering new lumped element model. New magnetic thin film inductors operating at 2GHz were fabricated on a Si substrate utilizing photo-lithography and lift-off techniques. The frequency characteristics of L, Q, and impedance in more than fifty identical inductors were measured using an RF Impedance Analyzer(HP4291B with HP16193A test fixture). The self-resonant frequencies(SRF) of the inductors were measured by a Vector Network Analyzer(HP8510). The developed inductors have SRF of 1.8 to 2.3GHz, L of 47 to 68nH, and Q of 70 to 80 near 1GHz. Finally, high frequency, high performance, planar micro-inductor(area=30.8 x 30.8il$^2$) with maximized L and Q were fabricated succefully.

• 한국정보통신설비학회:학술대회논문집
• /
• 2003.08a
• /
• pp.20-22
• /
• 2003

본 논문에서는 Photonic Bandgap(PBG)를 공진 특성을 이용하여 마이크로파 발진기의 위상잡음을 줄이기 위한 기술을 제시한다. 마이크로스트립 라인으로 구현한 공진기는 낮은 Q(Quality factor)를 가진다. PBG를 적용했을 때 공진기의 Q값을 높여줌으로써 발진기의 위상잡음 특성이 향상됨을 보이고자 한다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.12B
• /
• pp.1444-1451
• /
• 2009

This paper first proposes diverse C determining models in the Q algorithm which is proposed in the EPCglobal C1 Gen 2 standard and then compares and analyzes its performance. EPCglobal C1 Gen 2 standard proposes the slot-count (Q) selection algorithm for multiple tag identification environment, but there is no such definition for the C value which modifies the Q value depending on collision or no reply. During the tag anti-collision process, the Q algorithm adds C to the Q when there is a collision and reduces the Q by C when there is no reply. The modified Q value updates new slot-counts for tags which determines the tag identification speed, so the C value is an important factor. However, many researches only intend to increase the tag identification speed by proposing a new method or modifying the Q algorithm without any research about the C value. This paper suggests diverse C models which satisfies the EPCglobal C1 Gen 2 and analyzes their performance in the multi tag identification environment. The result of this paper can be used as an index for future researches on EPCglobal C1 Gen 2 C models and multiple tag identification performance.