• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.1729-1734
• /
• 2007

Recently, as the feasibility study shows that trans-Korea railway and trans-continental railway are advantageous, interest in high-speed railway system is increasing. Because railway vehicle is environment-friendly and safe compared with airplane and ship, its market-sharing increases gradually. We developed a measurement system for on-line test and evaluation of performances of KHST. The measurement system is composed of software part and hardware part. Perfect interface between multi-users is possible. Nowadays, position data inputs to pulse signal from wheel. Perfect position measurement was limited to slip and slide of vehicle. This measurement makes up for the weak points, Position Detection System using GPS develops. By using the system, Korean High Speed Train is capable of accurate fault position detection.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1102-1107
• /
• 2000

The signals that can be obtained from a rotating machine often convey the information of machine. For example, if the machine under investigation has faults, then we can measure the signal which has a pulse train, embedded in noise. Therefore the ability to detect the fault signal in noise determines the degree of diagnosis level of rotating machine. In this paper, minimum variance cepstrum (MV cepstrum), which can easily detect impulse in noise, has been applied to detect the type of faults of ball bearing system. To test the performance of this technique, experiment has been performed for ball bearing elements that have man made faults. Results show that minimum variance cepstrum can easily detect the periodicity due to faults.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.709-712
• /
• 1987

In this paper, a mathematical model for the purpose of QRS detection is considered in the case of the occurrence of nonoverlapping pulse-shaped waveforms corrupted with white noise. The number of waveforms, the arrival times, amplitudes, and widths of QRS complexes are regarded as random variables. The joint MAP estimation of all the unknown quantities consists of linear filtering followed by an optimization procedure. Because of time-consuming, the optimization procedure is modified so that a threshold test is obtained. The model formulation with nonoverlapping waveforms leads to a standard procedure covering a segment before as well as after an accepted event. Adaptivity of the detector is gained by utilizing past signal properties in determining threshold for QRS detection.

• Journal of Industrial Technology
• /
• v.19
• /
• pp.1-7
• /
• 1999

This is the pre-study to pile up the basic technique for the electro-discharge machining in the field of micro-drilling. The machined chips are flowed out from the machining area by the flow arisen from the high speed rotation of the electrode. The cylindrical shape electrode, whose diameter is 0.5mm, is clamped by the three point clamping type clamper and the clamper is attached at the front shaft of the high speed rotating DC motor. The current for machining is controlled by pulse width modulation technique and the machining conditions such as frequency and duty ratio are changed to find out the effect of the variables for machined results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.11
• /
• pp.1171-1177
• /
• 2009

A missile warning radar is an essential sensor for active protection system to detect antitank missile in all weather environments. This paper introduces missile warning radar for main battle tank and presents the results of the design and implementation of the radar signal processor using high speed multi-DSP. The key algorithms include adaptive CF AR, weighted linear fitting algorithm, S/W tracking capability, and threat decision and present test result.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.1
• /
• pp.77-85
• /
• 2009

With the advent of power semiconductor switching devices, power electronics relating to high frequency electromagnetic eddy current based induction heating technology have become more suitable and acceptable. This paper presents high-frequency induction heating cooking appliance circuit based on the zero current switching-PWM single ended push-pull(ZCS-PWM SEPP) resonant inverter added AC-DC converter. This inverter uses pulse-width-modulation(PWM) control method with active auxiliary quasi-resonant lossless inductor snubbers and a switched capacitor. To improved the transient performance, the PI controller is applied for this system. For the systematic parameter optimization of the PI controller, the gradient-based optimization algorithm is applied. The performance of optimized parameters is evaluated using simulation and experimental test. These results show that the proposed systematic optimal tuning method improve the transient performances of this system.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1999.11a
• /
• pp.228-233
• /
• 1999

In this paper we develop an electronic starter circuit that is suitable for Neon sign operation of switch-start fluorescent lamps. The developed starter enable single pulse ignition of fluorescent lamp at the peak point of preheating current, irrespective of the position of the Tum-On signal. This is possible due to the sequential operation of two transistors different in their operation characteristics and a diode operation characteristic. The switching endurance test using this starter has been carried for more than 3000 hours for a single switch-start on a severe blinking condition of preheating of 0.1s and of successive lighting interval of 0.1s.

• Computers and Concrete
• /
• v.21 no.5
• /
• pp.531-538
• /
• 2018

The slag through sieve #4 replaced the natural fine aggregate in different proportions (0-50%) to make ready-mixed soil and slag (RMSAS). The fresh properties studied, and the concrete specimens were produced to test the hardened properties at different ages. Results showed that the workability of RMSAS decreases when the replacement increases. The unit weight increases with the replacement. The setting time extends when the replacement decreases and shortens when the replacement increases. The compressive strength, ultrasonic pulse velocity and hammer rebound value increase with the replacement. However, the high-replacement results decrease because of the expansion factor at late age. Resistivity is close and less than $20k{\Omega}-cm$. After the industrial of steelmaking by-products are processed properly, they can be used in civil engineering, not only as a substitute for natural resources and to reduce costs, but also to provide environmental protection.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.4
• /
• pp.607-614
• /
• 2011

This paper describes the development of pulse code modulation(PCM) data recorder with design, implementation and environmental test. PCM serial data that diverged from telemetry encoder output is used as the input and is reformed to parallel signal through FPGA processing. Controllers construct the packet by the sector and record it into non-volatile memory. Compact flash(CF) memory for data storage media, USB interface for data downloading, and a software for operating status diagnosis and file format conversion are used.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.304-309
• /
• 2005

This paper presents an electronic ballast using a step down converter, a low frequency inverter for high intensity short-arc discharge lamp. The proposed ballast is composed of a full-wave rectifier, a step down converter operated as a current source with power regulation and a low frequency inverter with external ignition circuit. The ignition circuit generates high voltage pulse of $3{\sim}5[kV]$ peak, 130[Hz] periodically. Moreover, it is able to reignite at regular intervals by protective circuit. As experimental results on the test, acoustic resonance phenomenon is eliminated by operating the low frequency square wave voltage and current. Lamp voltage, current and consumption power are measured 123.8[V], 8.1[A] and 1,002[W], respectively. It was confirmed that the designed ballast operate the lamp with a constant power.