• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.781-781
• /
• 2009

We demonstrate that trasition metal catalyst nanoparticle (NP) attached to carbon nitride nanotubes (CNNTs) show selective catalytic activities on hydrogen generation from the water solution including chemical hydride negative ions. The natural bonding orbitals (NBO) obtained from the first-principle calculations shows that the catalysts attached on CNNTs are quite differently polarized when they play for hydrogen generation from chemical hydride ions and hydrogen of water. For Co and Ni nanoparticles attached on CNNTs, their charges are more positively polarized when they interact with $BH_4^-Na^+$ and $H_2O$ while Pt atoms are less positively charged. In this matter, the increased positive charges on catlyst nanoparticles are proven to be more efficient in attracting hydride negative ions, thus improving hydrogen generate rates. Consequently, this result implies that these different charge polarization leads to selective catalytic activities of NPs-CNNTs. In the hydrogen generation experiments, Co-CNNTs shows the highest hydrogen generation rate when the similar amounts of catalyst nanoparticles (Co, Ni, and Pt) are dispersed on the sidewalls of CNNTs.

• Journal of Korean Society of Water and Wastewater
• /
• v.26 no.3
• /
• pp.355-360
• /
• 2012

The characteristics of power generation were investigated by changing the electrical conductivity from 10 to 40mS/cm using air-cathode microbial fuel cell, which had graphite fiber fabric(GFF) anode. There were three kinds of cathode used: one was carbon cloth cathode coated with Pt, another was carbon nanotube(CNT) cathode with non-precious catalyst of Fe-Cu-Mn, and the other was carbon nanotube(CNT) cathode without any catalyst. When it was operated in batch mode, power density of 1369.5mW/$m^2$ was achieved at conductivity of 20mS/cm. Power density from MFC with CNT cathode coated with multi-catalyst of Fe-Cu-Mn was shown about 985.55mW/$m^2$, which was 75.1% compared the power density of carbon cloth coated with Pt. This meant that CNT cathode coated with multi-catalyst of Fe-Cu-Mn could be an alternative of carbon cloth cathode.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1236-1237
• /
• 2008

Carbon nanotube(CNT) materials are expected a stable current collector without the phenomena such as oxidizing and melting of grid by redox electrolyte and with low cost. In this paper, two types of dye-sensitized solar cells(DSSCs) with Pt abd CNT as a counter electrode were fabricated, then the energy conversion efficiency characteristics were investigated. The main purpose of this study is to find out the possibility of CNT material as cheap current collector of a large scale DSSC module. In addition, the Hall coefficient were measured by using FCM analysis.

• Korean Journal of Materials Research
• /
• v.19 no.4
• /
• pp.192-197
• /
• 2009

Carbon nanotubes (CNT) were used as a catalyst support where catalytically active Pd and Pt metal particles decorated the outside of the external CNT walls. In this study, Pd and Pt nanoparticles supported on $HNO_3$-treated CNT were prepared by microwave-assisted heating of the polyol process using $PdCl_2$ and $H_2PtCl_6{\codt}6H_2O$ precursors, respectively, and were then characterized by SEM, TEM, and Raman. Raman spectroscopy showed that the acid treated CNT had a higher intensity ratio of $I_D/I_G$ compared to that of non-treated CNT, indicating the formation of defects or functional groups on CNT after chemical oxidation. Microwave irradiation for total two minutes resulted in the formation of Pd and Pt nanoparticles on the acid treated CNT. The sizes of Pd and Pt nanoparticles were found to be less than 10 nm and 3 nm, respectively. Furthermore, the $SnO_2$ films doped with CNT decorated by Pd and Pt nanoparticles were prepared, and then the $NO_2$ gas response of these sensor films was evaluated under $1{\sim}5\;ppm$ $NO_2$ concentration at $200^{\circ}C$. It was found that the sensing property of the $SnO_2$ film sensor on $NO_2$ gas was greatly improved by the addition of CNT-supported Pd and Pt nanoparticles.

• Journal of the Korean Ceramic Society
• /
• v.45 no.6
• /
• pp.331-335
• /
• 2008

The purpose of this study is to characterize the photo-catalytic efficiency of $TiO_2$ nanotube with respect to the distribution of anatase phase which can be changed by the annealing temperature of $TiO_2$ nanotube. $TiO_2$ nanotube was fabricated by the anodization method in the 0.5 wt% HF electrolyte. And then the $TiO_2$ nanotube was annealed at temperatures ranging from $380^{\circ}C$ to $780^{\circ}C$ in dry oxygen ambient for 2 h. For the photo-catalytic water-splitting tests, the photocurrent density was measured as a function of applied potential with a potentiostat using a Ag/AgCl reference, Pt counter electrode, and 1 M KOH electrolyte under illumination of UV by a Xe arc lamp of 1 KW. According to the UV photo-catalytic water-splitting tests, the nanotube annealed at $560^{\circ}C$ was found to show the highest photocurrent density.

• Journal of Sensor Science and Technology
• /
• v.32 no.5
• /
• pp.290-294
• /
• 2023

Among various types of harmful gases, hydrogen sulfide is a strong toxic gas that is mainly generated during spillage and wastewater treatment at industrial sites. Hydrogen sulfide can irritate the conjunctiva even at low concentrations of less than 10 ppm, cause coughing, paralysis of smell and respiratory failure at a concentration of 100 ppm, and coma and permanent brain loss at concentrations above 1000 ppm. Therefore, rapid detection of hydrogen sulfide among harmful gases is extremely important for our safety, health, and comfortable living environment. Most hydrogen sulfide gas sensors that have been reported are electrical resistive metal oxide-based semiconductor gas sensors that are easy to manufacture and mass-produce and have the advantage of high sensitivity; however, they have low gas selectivity. In contrast, the electrochemical sensor measures the concentration of hydrogen sulfide using an electrochemical reaction between hydrogen sulfide, an electrode, and an electrolyte. Electrochemical sensors have various advantages, including sensitivity, selectivity, fast response time, and the ability to measure room temperature. However, most electrochemical hydrogen sulfide gas sensors depend on imports. Although domestic technologies and products exist, more research is required on their long-term stability and reliability. Therefore, this study includes the processes from electrode material synthesis to sensor fabrication and characteristic evaluation, and introduces the sensor structure design and material selection to improve the sensitivity and selectivity of the sensor. A sensor case was fabricated using a 3D printer, and an Ag reference electrode, and a Pt counter electrode were deposited and applied to a Polytetrafluoroethylene (PTFE) filter using PVD. The working electrode was also deposited on a PTFE filter using vacuum filtration, and an electrochemical hydrogen sulfide gas sensor capable of measuring concentrations as low as 0.6 ppm was developed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.335-338
• /
• 2007

Cost effectiveness is an important parameter for producing DSSCs as compared to the widely used conventional silicon based solar cells. A fluorine-doped tin oxide (FTO) substrate coated with a catalytic amount of platinum is used as counter electrode in dye-sensitized solar cell. Carbonaceous materials are quite attractive to replace platinum due to their high electronic conductivity, corrosion resistance towards $I_{2}$, good catalytic effect and low cost. In this paper, the unit DSSCs with Pt and CNT as a counter electrode were connected in series-parallel externally, then the current-voltage curves were investigated to find out the connection characteristics of the DSSC with CNT counter electrode. The connection characteristics of the DSSC with CNT counter electrode is superior to that of the DSSC with Pt counter electrode. And a parallel connection of the DSSC with CNT counter electrode has higher efficiency than a series connection of that.

• Journal of Energy Engineering
• /
• v.18 no.2
• /
• pp.141-146
• /
• 2009

In present work, we study the hydrogen storage of MWNT decorated with bimetallic Pt and Pd nanosize catalysts by Thermal Vapor Deposition [TVD]. The size of Pt and Pd particles is controlled as 5nm, 3nm, respectively by TVD. Before hydrogen storage measurement, the sample was heated for 1hr at $200^{\circ}C$ in H2 atmosphere. The Hydrogen sto rage of the sample was performed at room temperature and 33~34atm. The hydrogen storage of this composite showed 3.2wt% at 298K and 34atm, for three times. At 4th cycle, hydrogen storage is decreased to 1.5wt%, owing to the aggregation of bimetallic Pt and Pd nano particles.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.4
• /
• pp.140-143
• /
• 2005

Carbon Nanotube(CNTs) counter electrode is a promising alternative to Platinum counter electrode for dye sensitized solar cells (DSSCs). In this study, CNT counter electrodes having different visible light transmittance were prepared on fluorine-doped tin oxide (FTO) glass surface by spray coating method. Microstructural images show that there are CNT-tangled region coated on FTO glass counter electrodes. Using such CNT counter electrodes and screen printed $TiO_2$ electrodes, DSSCs were assembled and its I-V characteristics have been studied and compared. Light energy conversion efficiency of DSSCs increased with decreasing in light transmittance of CNT counter electrode. Efficiency of DSSCs having CNT counter electrode is compatible to that of Pt counter electrode.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.135.2-135.2
• /
• 2010

Carbon nanotube(CNT) has been spotlighted as a promising candidate for catalyst support material for PEMFC (proton exchange membrane fuel cell). The considerable properties of CNT include high surface area, outstanding thermal, electrical conductivity and mechanical stability. In this study, to fully utilize the properties of CNTs, we prepared directly oriented CNT on carbon paper as a catalyst support in the cathode electrode. The CNT layer was prepared by a chemical vapor deposition(CVD) process. And the Pt particles were deposited on the CNT oriented carbon paper by impregnation and eletro-deposition method. The potential advantages of directly oriented CNT on carbon paper can include improved thermal and charge transfer through direct contact between the electrolyte and the electrode and enhanced exposure of Pt catalyst sites during the reaction.