• Journal of the Korean Electrochemical Society
• /
• v.10 no.1
• /
• pp.25-30
• /
• 2007

Proton exchange membrane fuel cell(PEMFC) performance could be affected by various factors such as cell temperature, total pressure, partial pressure of reactants and relative humidity. Hydrogen ion is combined with water to form hydronium ion [$H_3O^+$] and pass through membrane resulting electricity generation. Cooling system is needed to remove heat and other uses on large scale fuel cell. In case that collant conductivity is increased, fuel cell performance could be decreased because produced electricity could be leaked through coolant. In this study, triple distilled water(TDW) and antifreeze solution containing ethylene glycol was used to observe resistance change. Resistance of TDW was taken 28 days to reach preset value, and effect on fuel cell operation was not observed. Resistance of antifreeze solution was not reached to preset value up to 48 days, but performance failure occurred presumably caused by bipolar plate junction resulting stoppage resistance experiment. Generally PEMFC humidification is performed near-saturated operating conditions at various temperatures and pressures, but non-humidifying condition could be applied in small scale fuel cell to improve efficiency and reduce system cost. However, it was difficult to operate large scale fuel cell without humidifying, especially higher than $50{\sim}60^{\circ}C$. In case of small flux such as 0.78 L/min, temperature difference between inlet and outlet was occurred larger than other cases resulting performance decrease. Non-humidifying performance experiments were done at various cell temperature. When both of anode and cathode humidification were removed, cell performance was strongly depended on cell operating temperature.

• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.847-853
• /
• 2016

Here has been examined a 3-dimensional computational fluid dynamics (CFD) modeling in order to investigate the performance analysis of proton exchange membrane (PEM) fuel cells with serpentine flow fields. The present CFD model considers the isothermal transport phenomena in a fuel cell involving mass, momentum transport, electrode kinetics, and potential fields. Co-current flow patterns for a PEMFC are considered for various geometries in the single straight cell. Current density distribution from the calculated distribution of oxygen and hydrogen mass fractions has been determined, where the activation overpotential has been also calculated within anode and cathode. CFD results showed that profiles differ from those simulations subjected to each the calculated activation overpotential. It is interesting that the present serpentine flow field shows the specific distribution of current density with respect to the aspect ratio of depth to width and the ratio of reaction area for various serpentine geometries. Simulation results were considered reasonable with the other CFD results reported in literature and global comparisons of the PEMFC model.

• Journal of Electrochemical Science and Technology
• /
• v.14 no.4
• /
• pp.333-348
• /
• 2023

In this study, a 3D model of the proton exchange membrane fuel cell is established, and a new 3D baffle structure is designed, which is combined with the parallel flow field and then optimized by numerical simulation methods. The number of baffles and the cross-sectional trapezoidal base angle are taken as the main variables, and their impacts on the performance indexes of the cathode side are analyzed. The results show that the 3D baffle can facilitate the convection and diffusion mass transfer of reactants, improve the uniformity of oxygen distribution, enhance the drainage capacity, and make the cell performance superior; however, too small angle will lead to excessive local convective mass flux, resulting in the decrease of the overall uniformity of oxygen distribution and lowering the cell performance. Among them, the optimal number of baffles and angle are 9 and 58°, respectively, which improves the net output power density by 10.8% than conventional flow field.

• Journal of Hydrogen and New Energy
• /
• v.25 no.4
• /
• pp.393-404
• /
• 2014

Unmanned aerial vehicles (UAVs) have been applied to not only military missions like surveillance and reconnaissance but also commercial missions like meteorological observation, aerial photograph, communication relay, internet network build and disaster observation. Fuel cells make UAVs eco-friendly by using hydrogen. Proton exchange membrane fuel cells (PEMFCs) show low operation temperature, high efficiency, low noise and high energy density and those characterisitcs are well fitted with UAVs. Thus Fuel cell based UAVs have been actively developed in the world. Recently, fuel cell UAVs have started to develope for high altitude UAVs because target altitude of UAVs is expanded upto stratosphere altitude. Long endurance of UAVs is essential to improve effects of the missions. Improvement of UAV endurance time could be fulfilled by developing a hydrogen fuel storage system with high energy density and reducing the weight of UAVs. In this paper, research trend and analysis of fuel cell UAVs are introduced in terms of their altitude and endurance time and then the prospect of fuel cell UAVs are shown.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.251-258
• /
• 2016

This article reports current status of micro fuel cell-combined heat and power (${\mu}FC$-CHP) systems which utilize both power and heat generated by fuel cells. There are several options for constructing CHP systems and among them, fuel cells are the most useful and their total energy efficiency combining heat and power can reach up to about 90%. Fuel cells are classified as five types based on the electrolyte, but the most suitable fuel cell types for the ${\mu}FC$-CHP system are proton exchange membrane fuel cells (PEMFCs) and solid oxide fuel cells (SOFCs). ${\mu}FC$-CHP systems have several advantages such as decrease of the transmission-distribution loss, reduced costs of electricity due to distributed power generation, and environmental-friendliness owing to zero emission. The main drawback of the ${\mu}FC$-CHP systems is the high initial investment, however, it keeps decreasing as the technology development reduces production costs. Currently, Japan is the most leading country of the ${\mu}FC$-CHP market, however, Korea tries to expand the market by planning the deployment of 1 million units of ${\mu}FC$-CHP systems and governmental subsidiary supporting of half of the install price. In this report, integration technologies for connecting FC and CHP, and technology trends of leading countries are presented as well.

• Journal of Hydrogen and New Energy
• /
• v.28 no.5
• /
• pp.471-480
• /
• 2017

A proton exchange membrane fuel cell (PEMFC) operated at $150^{\circ}C$ was evaluated by a controlling different amount of phosphoric acid (PA) to a membrane-electrode assembly (MEA) without humidification of the cells. The effects on MEA performance of the amount of PA in the cathode are investigated. The PA content in the cathodes was optimized for higher catalyst utilization. The highest value of the active electrochemical area is achieved with the optimum amount of PA in the cathode confirmed by in-situ cyclic voltammetry. The current density-voltage experiments (I-V curve) also shows a transient response of cell voltage affected by the amount of PA in the electrodes. Furthermore, this information was compared with the production variables such as hot pressing and vacuum drying to investigate those effect to the electrochemical performances.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.3
• /
• pp.22-29
• /
• 2004

Deformation of the porous media has influence on performance of a proton exchange membrane fuel cell (PEMFC). The stress distributions and deformation of the porous media are major factors for safe and efficient operation in the PEMFC. In this paper, nonlinear contact analysis of air plate and porous media is performed under a working condition to predict the performance characteristics of the air plates. Two kinds of models are suggested for this study. The first porous media model has nonlinear material properties. The second model has nonlinear material properties with contact condition between porous media and air plate. The numerical analysis results of the two models are somewhat different. It is shown that the nonlinear contact analysis is required for the design study of the PEMFC.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.41-49
• /
• 2004

The porous media of a proton exchange membrane fuel cell (PEMFC) is made of deformable materials. The shape of cross sectional area in air plate channels has been changed by structural deformation of the porous media. The uniform mass flow rate and pressure are major factors for safe and efficient operation in the PEMFC. Two kinds of models are provided for the flow analyses. Deformable and undeformable porous media are considered for numerical analysis and experiment of the air plate model. The numerical flow analysis results with deformable and undeformable porous media has some discrepancy in pressure distribution. The pressure differences are measured in order to compare with numerical analysis results. Pressures are measured between inlet and outlet of the air plate. The numerical analysis and experimental results show similar pressure distribution. It is shown that the pressure drops in the two approaches are well matched each other. It is proven that the consideration of structural deformation is required in the numerical analysis/experiment for the PEMFC design.

• Korean Chemical Engineering Research
• /
• v.56 no.1
• /
• pp.1-5
• /
• 2018

In this work, we study the ion conductivity by analyzing the impedance to the high current density range that the PEMFC (Proton Exchange Membrane Fuel Cell) is actually operated. The effect of GDL (Gas Diffusion Layer)presence on impedance was investigated indirectly by measuring hydrogen permeability. When the RH (Relative Humidity)was higher than 60% in the low current range (< $80mA/cm^2$), the moisture content of the polymer membrane was sufficient and the ion conductivity of the membrane was not influenced by the current change. However, when RH was low, ion conductivity increased due to water production as current density increased. The ion conductivity of the membrane obtained by HFR (High Frequency Resistance) in the high current region ($100{\sim}800mA/cm^2$)was compared with the measured value and simulated value. At RH 100%, both experimental and simulated values showed constant ion conductivity without being influenced by current change. At 30~70% of RH, the ionic conductivity increased with increasing current density and tended to be constant.

• New & Renewable Energy
• /
• v.6 no.1
• /
• pp.46-52
• /
• 2010

Membrane electrode assemblies (MEAs) for proton exchange membrane fuel cells (PEMFCs) have been extensively studied to improve their initial performance as well as their durability and to facilitate the commercialization of fuel cell technology. To improve the MEA performance, particularly at low Pt loadings, many approaches have been made. In the present study, MEA performance improvement was performed by adding $TiO_2$ particles into the catalyst layer of MEA. Most of previous studies have focused on the MEA performance enhancement under low humidity conditions by adding metal oxides into the catalyst layer mainly due to the water keeping ability of those metal oxides particles such as $Al_2O_3$, $SiO_2$ and zeolites. However, this study mainly focused on the improvement of MEA performance under fully humidified normal conditions. In this study, the MEA was prepared by decal method aiming for a continuous MEA fabrication process. The decal process can make very thin and uniform catalyst layer on the surface of electrolyte membrane resulting in very low interfacial resistance between catalyst layer and the membrane surface and uniform electrode structure in the MEA. It was found that the addition of $TiO_2$ particles into the catalyst layer made by decal method can minimize water flooding in the catalyst layer, resulting in the improvement of MEA performance.