• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.3
• /
• pp.82-89
• /
• 2012

The temperature of cryogenic propellant in the propellant tank increases during flight due to heat input from surroundings. The propellant which temperature rises up over the required condition of turbo-pump remains as unusable propellant at the end of flight. In this paper the estimation method of the heat transfer coefficient at the upper layer of cryogenic propellant was presented. The heat transfer mode at the propellant upper layer was considered as conduction. Temperature distributions near propellant surface obtained from heat transfer coefficient were compared with test data to show the possibility of this method.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.709-716
• /
• 2011

The temperature of cryogenic propellant in the propellant tank increases during flight due to heat input from surroundings. The propellant which temperature rises up over the required condition of turbo-pump remains as unusable propellant at the end of flight. In this paper the estimation method of the heat transfer coefficient at the upper layer of cryogenic propellant was presented. The heat transfer mode at the propellant upper layer was considered as conduction. Temperature distributions near propellant surface obtained from heat transfer coefficient were compared with test data to show the possibility of this method.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.645-648
• /
• 2011

Hydrazine which has been used as monopropellant shows high performance, but because of its high toxicity research for new green propellant that could replace hydrazine is going on. Ionic liquid propellant that is one of the green propellant has lower toxicity, higher specific impulse, and higher density than hydrazine. To design the thruster which use Hydroxylamine Nitrate (HAN), one of ionic liquid propellant, as a propellant, a quantity of catalyst for full decomposition of a propellant is needed. In this study, reference point for HAN thruster design could be suggested through a design of a small scale thruster which used HAN propellant, and propellant decomposition capability evaluation with characteristic velocity efficiency.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.5
• /
• pp.84-90
• /
• 2020

The adhesion strength of two konds of solid propellants(primary propellant/secondary propellant) was studied by coating agent of adhesion composition composed of organic solvent, curing agent, and cure catalyst. The coating agent using FeAA, cure catalyst, resulted propellant breaking at more 0.14 wt% and interface breaking at less 0.10 wt%. The TPB cure catalyst of confirmed the result of the interface breaking immediately after curing of the secondary propellant. In addition, the coating agent using TPB was found to increase the adhesion strength between the primary propellant and the secondary propellant over time.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.203-206
• /
• 2006

We have studied, for maximizing the total impulse of liquid propulsion system, Propellant Utilization System (PUS) to minimize outage of propellant. Propellant outage is mainly influenced by propellant mixture ratio during flight and real quantity of loaded propellant. If one employs cryogenic propellant, the variation of propellant density due to the temperature change has major effect on outage control. Feedback control of propellant level of each tank during flight could deplete both tanks simultaneously. To introduce this system, however, the mixture ratio control system of rocket engine is necessary.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.79-82
• /
• 2004

Propellant feeding system is the system to satisfy propellant feeding requirements(mass flow rate, pressure, temperature) at engine inlet of launch vehicle. Propellant feeding test facility is being constructed for the development scheme of pressurization system, processing in tank, propellant piping system, and flow control system that are main technologies in order to develope propellant feeding system. This paper introduces the propellant feeding test facility being constructed in KARI.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.2
• /
• pp.38-51
• /
• 2018

This study was carried out to improve the performance characteristics of nozzleless boosters that are used in ramjet boosters. A propellant using Zr as the metal fuel was developed, which provided a higher density than the propellant using Al as the metal fuel. The developed propellant was cast using the nozzleless booster and a ground test was carried out by varying the length-to-diameter ratio (L/D ratio) of the propellant. From a comparison between the performance characteristics of propellants using Zr and Al, it was proved that the performance of the propellant using Zr is higher than that of propellant using Al, except for the specific impulse, under all tested conditions. As the length-to-diameter ratio was increased, the specific impulse of the propellant using Zr was decreased by 88% compared with that of the propellant with Al. However, because of the density difference between the propellants, the impulse density of the propellant with Zr was higher than that of the propellant with Al under all tested conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.1
• /
• pp.34-42
• /
• 2007

Ultrasonic inspection method is more profitable than X-ray radiographic inspection in cost and effect of defect detection such as debond, damage, and it doesn't need special constructions. The method can also be a possible real time inspection with safety. This report explains 1)the experiment and analysis of ultrasonic property of solid propellant, 2)the inspection methods of propellant/liner debond by inside or outside inspection, and 3)the inspection methods of propellant microcrack by damage. From the results, it is possible to detect the defect of propellant/liner debond by inside or outside inspection. Futhermore, it can be possible to detect the propellant microcrack caused by damage using the ultrasonic attenuation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.972-977
• /
• 2017

The propellant tile and crack which account for the greatest proportion of solid rockets are profoundly affected by viscosity and mechanical properties of solid propellant. In this paper solid propellant with nitrate ester polyester(NEPE) system has been researched for the viscosity, mechanical properties and burning properties with size and mixing ratio of RDX. the viscosity of propellant was changed significantly depending on the size of RDX and mixing ratio, and mechanical properties of NEPE system propellant were also varied. Considering both lower viscosity and stable mechanical properties, the optimum size and mixing ratio of RDX can be identified as the main factors to the NEPE system propellant.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.351-355
• /
• 2011

In this study, 2 kinds of HTPE insensitive propellants composed of HTPE/BuNENA binder, AP, AN and Al were investigated for combustion characteristics, ignition delay time, sensitivity and insensitive properties compared with HTPB propellant. HTPE propellant showed almost same sensitivity results as HTPB propellant, showed 2~3 times higher value than the value of HTPB propellant, ignition delay time respectively, and met the standard criteria, while HTPB propellant failed.