• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.803-806
• /
• 1995

The vibration and nosic of gears is causeed by manufacting error,alignment error in assembly, and thr meshing stiffness of gears which changes periodically as the meshing of teeth process. On a pair of power transmission helical gears with profile error, the relation between the characteristics of gear vibration and the profile error type have been investigated by simulating the vibrational acceleration level and calculating the natural frequency. The results show that the profile error decrease the natural frequency by reducing the tool stiffness and that the concave error type increase the vibrationsl level. And this paper describes the effect of the tip relief on the vibrational acceleration level which a pair of helical gears with concave error generates.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.451-454
• /
• 2002

In the present paper, the practicability of Commentray on Wind Loads of Korean Standard Design Loads fur Buildings, which has been enacted in Minstry of Construction and Transportation in June 2000, is validated by using the meteorological data measured at Homi-Cape, Pohang. Assuming that the vertical wind profile follows the power-law in a quasi-steady state, wind profile exponents are calculated by seasons by using wind data as collected through four monitoring towers. According to the Commentray on Wind Loads, Pohang is classified with its exposure category being B and the wind profile exponent being 0.22, while it is identified that the average wind profile exponent as calculated in this study is 0.26. Also, in this paper, a cross-correlation method is suggested in order to identify any meteorological correlation between measurement sites quantitatively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제13권4호
• /
• pp.282-290
• /
• 2013

This paper describes a spread spectrum clock generator (SSCG) circuit for DisplayPort 1.2 standard. A Hershey-Kiss modulation profile is generated by dual sigma-delta modulators. The structure generates various modulation slopes to shape a non-linear modulation profile. The proposed SSCG for DisplayPort 1.2 generates clock signals with 5000 ppm down spreading with a Hershey-Kiss modulation profile at three different clock frequencies, 540 MHz, 270 MHz and 162 MHz. The measured peak power reduction is about 15.6 dB at 540 MHz with the chip fabricated using a $0.13{\mu}m$ CMOS technology.

• Journal of Electrical Engineering and Technology
• /
• 제7권3호
• /
• pp.281-287
• /
• 2012

The customer load profile clustering method is used to make the TDLP (Typical Daily Load Profile) to estimate the quarter hourly load profile of non-AMR (Automatic Meter Reading) customers. This study examines how the repeated clustering method improves the ability to discriminate among the TDLPs of each cluster. The k-means algorithm is a well-known clustering technology in data mining. Repeated clustering groups the cluster into sub-clusters with the k-means algorithm and chooses the sub-cluster that has the maximum average error and repeats clustering until the final cluster count is satisfied.

• 한국기계가공학회지
• /
• 제9권5호
• /
• pp.40-49
• /
• 2010

Conical involute gears are being used for marine gearboxes, automotive transmissions, and robots, and so on, but not much. As involute profile gear, conical involute gear not only can be engaged with spur and helical gear but also can be used for power transmission of parallel, crossed and skewed axis with small angle. Hence, conical involute gears are likely to develop in future. Through a study on the basic theory of conical involute gear, tooth surface compressive stress analysis was performed by using commercial modeling program, comparing before and after profile modification. As a result, it noticed that tooth profile modification is able to relieve more tooth surface compressive stress than before modification.

• 한국기계기술학회지
• /
• 제13권3호
• /
• pp.17-23
• /
• 2011

To estimate fuel consumption of a vehicle, a car can be tested on chassis dynamometer. In this case, test causes a lot of time and money. To predict the fuel efficiency of vehicles in the design stage or early stage of development, the development of computer simulation model is necessary. Using simulation to predict the fuel consumption, the driving model which consists of time-velocity profile and time-grade profile is necessary In this study, vehicle model is developed in MatLab/simulink to estimate real driving fuel consumption rate with time-velocity profile, time-shift gear profile and time-grade profile. Vehicle model consists of driver model, engine model, power train model, and so on. On-road vehicle tests to verify the vehicle model are carried out for analyzing the result of simulation and comparing with those of the experiments.

• 조명전기설비학회논문지
• /
• 제28권5호
• /
• pp.82-91
• /
• 2014

The combined generator system by integrating several renewable energy sources can share the electrical infrastructure and therefore have the advantage of constructing not only the transmission system but also the power conversion system. Among the various combined renewable system, the wind power and wave power has a high possibility of future growth due to the economic feasibility in offshore environment. This kind of large-scale combined systems might be follow the determination by the transmission system operator's directions and control the output profile by focusing at PCC. However, both renewable energies are depend on the unpredictable environmental variation; it is needed to do the compensation devices. In this paper, the ESS compensation plan is proposed to do output determination of the combined generator system by paying attention to active power of utility grid with the analysis of the controllable elements of the wind and wave power generator. The improvement of the new application technique of the combined system is confirmed through using the PSCAD/EMTDC. The entire simulation process was designed by adopting the active power control according to the reference signal of TSO.

• 전력전자학회논문지
• /
• 제12권3호
• /
• pp.221-233
• /
• 2007

본 논문에서는 고성능 단축 선형전동기에 적용할 수 있는 최단시간 위치 패턴 알고리즘에 대하여 논한다. 근래 들어 LCD/PDP 및 반도체 산업이 발달함에 따라 대형의 고성능 위치제어 시스템에 대한 요구가 높아지고 있으며 이러한 시스템에서는 공정 주기의 단축을 위하여 시간요소를 최소화시킨 최적 위치 패턴이 반드시 필요하다. 특히 반도체 산업 분야에서는 공작기계 분야와 달리 3차원 입체 위치 패턴보다는 단축 패턴에 대한 수요가 비교적 많은 편이다. 본 연구에서는 가속도가 사다리형인 위치 패턴을 기본으로 하여 연구를 진행하였으며 위치 및 시간을 변수로 고려한 패턴 분석을 통하여 최단시간에 목적하는 위치에 도달하기 위한 패턴을 비교적 간단히 구현할 수 있음을 보이고 이를 시뮬레이션 및 간이 실험으로 구현 가능성을 입증하였다.

• Journal of Electrical Engineering and Technology
• /
• 제1권2호
• /
• pp.237-240
• /
• 2006

The feasibility of a midgap metal gate is investigated for a 32 nm MOSFET for low power applications. The midgap metal gate MOSFET is found to deliver $I_{on}$ as high as a bandedge gate if a proper retrograde channel is used. An adequate design of the retrograde channel is essential to achieve the performance requirement given in the ITRS roadmap. A process simulation is also run to evaluate the feasibility of the necessary retrograde profile in manufacturing environments. Based on the simulated result, it is found that any subsequent thermal process should be tightly controlled to retain transistor performance, which is achieved using the retrograde doping profile. Also, the bandedge gate MOSFET is determined be more vulnerable to the subsequent thermal processes than the midgap gate MOSFET. A guideline for gate workfunction $(\Phi_m)$ is suggested for the 32 nm MOSFET.

• Tribology and Lubricants
• /
• 제20권3호
• /
• pp.157-162
• /
• 2004

The cam curve of a balance type vane pump consists usually of circular arcs and Archimedes' spirals. However, if they are connected directly together, the curve must have a few discontinuous points of the gradients and the motion of the vanes is no longer smooth. Designing data for an oil hydraulic vane pump used in power steering system were obtained by the acquisition of optimum cam profile data which can be available to reduce noises and vibrations through the minimization of cavitation with the improvement of suctional performance. The performance test is carried on the trial manufactures by measuring the volumetric and the mechanical efficiency. And from that result, maintaining the same characteristic as the conventional one in the relief pressure and noise level, the experimental pump discharges 0.7 $\ell$/min and shows nearly 3.5% enhancement in the total efficiency more than the conventional one.