• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.12
• /
• pp.560-564
• /
• 2006

ZnO thin films were prepared by RF magnetron sputter deposition on p-Si(100) wafer with various cooling rates of substrate temperature such as the substrates were pre-heated to $400^{\circ}C$ before the deposition and then cooled down naturally or slowly to $300^{\circ}C,\;200^{\circ}C,\;100^{\circ}C$, and R.T. by the temperature controller during the deposition. Crystalline and micro-structural characteristics of the films were investigated by XRD and SEM. ZnO films which cooled down naturally or slowly by the temperature controller during the deposition, especially the film were deposited with cooling down from $400^{\circ}C\;to\;200^{\circ}C$ slowly. showed the most outstanding c-axis preferred orientation.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1864-1865
• /
• 2007

In this paper, we proposed pre-filter algorithms which using frequency domain analysis method, for the detections of defects in large-sized Thin Film Transistor-Liquid Crystal Display(TFT-LCD) panel surfaces. We performed frequency analysis with 1-D, 2-D FFT methods for extract periodic patterns of lattice structures in TFT-LCDs. To remove this patterns, band-stop filters were used for eliminating specific frequency components. In order to acquire only defected images, we used 2-D inverse FFT methods which can be reverts images that remains defects.

• Electrical & Electronic Materials
• /
• v.10 no.5
• /
• pp.453-460
• /
• 1997

In order to investigate the electrical conduction properties of polyethylene thin film for power cable with manufacturing methods, the thickness of specimen was the 30, 100[${\mu}{\textrm}{m}$] of LDPE and 200[${\mu}{\textrm}{m}$] of XLPE were manufactured. The experimental condition for conduction properties was measured until the breakdown occurs at temperature ranges from 30 to 110[$^{\circ}C$] and the electric field from 1$\times$10$^3$to 5$\times$10$^{6}$ [V/cm]. As for increase of temperature, the current density of LDPE was increased with constant ratio in low field, but changes with exponential function in high electric field. The tunnel current of pre-breakdown region is shifted toward low field as much as thermal excitation energy. At low electric field, the XLPE showed dominant electrical conduction properties by thermal excitation, and transformation of the electron was resisted by the crystal at high electric field.

• Journal of Satellite, Information and Communications
• /
• v.3 no.1
• /
• pp.1-7
• /
• 2008

This Paper studied the design and measured results of a flight model for Ku-Band Linearized Channel Amplifier (LCAMP) for communication satellite onboard system. All MMICs, i.e. Variable Gain Amplifier (VGA), Variable Voltage Attenuator (VVA) with analog/digital attenuator, Branch line Hybrid Coupler and Detector for Pre-distorter are fabricated using Thin-Film Hybrid process. The performance of the fabricated module is verified through Radio Frequency circuit simulations and electrical function test in space environment for flight model at 12.25 to 12.75 GHz.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.10
• /
• pp.51-58
• /
• 1993

N-channel TFTs fabricated on the pre-amorphized (by Si ion implantation) and recrystallized Si film having 10.1V threshold voltage, 20.7cm$^{2}$/V$\cdot$s field effect mobility and ~10$^{5}$/ ON/OFF ratio, whowed improved characteristics comparing to those obtained from the as-deposited (by LPCVD) poly Si film which had 11.2V, 9cm$^{2}$/V$\cdot$s and ~10$^{4}$ respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1229-1232
• /
• 2008

We have successfully manufactured high-quality top-contact organic thin-film transistors using inkjet technologies with sub-femtoliter droplet volume. Silver fine lines were directly patterned by inkjet on pentacene channel layers. The minimum width of silver lines was $1{\mu}m$ with without the need for pre-patterning or surface pretreatments. The mobility was $0.3\;cm^2/Vs$.

• Journal of the Korean Ceramic Society
• /
• v.44 no.10
• /
• pp.548-553
• /
• 2007

Ceramic green sheets consisting Bi-based glass frit were fabricated for an application to PDP transparent dielectric front panel. The dispersion condition of the slurry for tape casting was pre-examined, and two kinds of hinder and plasticizer were used in the non-aqueous slurry system. In the fabrication process for the frit film, the properties such as dry and firing shrinkage, elongation, and transmittance were examined at the condition of various mixing ratio of plasticizers. In the mixing ratio of polyethylene glycol to dibutyl phthalate of 3:5wt%, a good adhesion, elongation and transmittance were observed at the firing temperature of $580^{\circ}C$. The photograph for the cross section of the interface was also showed a dense microstructure.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.221-226
• /
• 2008

Numerical simulation is performed for microdroplet deposition on a pre-patterned micro-structure. The level-set method for tracking the liquid-gas interface is extended to treat the immersed (or irregular-shaped) solid surface. The no-slip condition at the fluid-solid interface as well as the matching conditions at the liquid-gas interface is accurately imposed by incorporating the ghost fluid approach based on a sharp-interface representation. The method is further extended to treat the contact angle condition at an immersed solid surface. The present computation of a patterning process using microdroplet ejection demonstrates that the multiphase characteristics between the liquid-gas-solid phases can be used to improve the patterning accuracy.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.10a
• /
• pp.221-226
• /
• 2008

Numerical simulation is performed for microdroplet deposition on a pre-patterned micro-structure. The level-set method for tracking the liquid-gas interface is extended to treat the immersed (or irregular-shaped) solid surface. The no-slip condition at the fluid-solid interface as well as the matching conditions at the liquid-gas interface is accurately imposed by incorporating the ghost fluid approach based on a sharp-interface representation. The method is further extended to treat the contact angle condition at an immersed solid surface. The present computation of a patterning process using microdroplet ejection demonstrates that the multiphase characteristics between the liquid-gas-solid phases can be used to improve the patterning accuracy.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.658-659
• /
• 2008

Numerical simulation is performed for a microdroplet deposition on the pre-patterned micro-structure. The liquid-air interface is tracked by level set method improved by incorporating the ghost fluid approach based on a sharp-interface representation. The method is further extended to treat the contact angle condition at an immersed solid surface. The present computation of a patterning process using microdroplet ejection demonstrates that the multiphase characteristics between the liquid-gas-solid phases can be used to overcome the patterning error.