• 한국구조물진단유지관리공학회 논문집
• /
• 제21권2호
• /
• pp.53-59
• /
• 2017

본 연구에서는 고온에 노출된 GFRP 보강근과 고온에 노출된 후 알칼리용액에 노출된 보강근의 단면을 현미경을 통해 관찰하고 발생된 손상의 특징을 고찰하였다. 또한, 각 시험체에 발생한 레진 균열과 공극에 대한 정량적 분석을 실시하였다. 알칼리로 인한 손상은 주로 표면에 집중되며 레진균열과 작은 공극을 발생시키는 것으로 확인되었다. 고온노출에 의한 손상은 레진균열과 공극을 발생시키는 것은 알칼리와 동일하지만 전단면에서 발생하며, 공극의 크기가 훨씬 크다. 또한 정량분석 결과, 동일한 알칼리 용액 노출조건에도 불구하고, $200^{\circ}C$ 이상의 고온에 노출된 시편에서 발견된 레진 균열과 공극이 고온노출이력이 전혀 없는 보강근에서 발견된 것 보다 1.5 및 1.4배 큰 것으로 확인되었다. 그러므로 동일한 알칼리 노출 조건이라 할지라도 $200^{\circ}C$ 이상의 고온에 노출된 보강근은 고온노출이력이 없는 보강근에 비하여 레진의 열화가 가속화 될 가능성이 있음을 알 수 있다.

• 한국군사과학기술학회지
• /
• 제17권4호
• /
• pp.413-421
• /
• 2014

Since the structural temperature of a flight vehicle flying at high speed rises rapidly due to aerodynamic heating, it is necessary for optimum structural design to obtain proper material properties at high temperature by taking into account of its operational environment. For a special alloy, analysis data on strength change due to exposure time to high temperature are very limited, and most of them are for an exposure time longer than 30 minutes for long term operations. In this study, base and weld metal samples of Ti-6Al-4V alloy had been prepared and high temperature tensile tests with induction heating were performed, and then high temperature strength characteristics and strength recovery characteristics through cooling have been analyzed. Pre-tests to determine maximum heating rate were performed, and response characteristics for temperature control were confirmed. As a result, high temperature tensile strength appeared to be lower than that of room temperature, but it was higher than that of high temperature of 30 minite exposure listed in MMPDS. In strength recovery through cooling Ti-6Al-4V alloy has shown higher recovery rate compared with other alloys.

• 대한토목학회논문집
• /
• 제35권1호
• /
• pp.77-84
• /
• 2015

고온에 노출된 GFRP 보강근의 인장실험을 수행하였다. 본 실험을 위한 고온노출조건은 $200^{\circ}C$ 이하의 온도에 3분간 노출하는 것으로 하였다. 이러한 조건은 다른 연구자들의 시험에서 적용한 고온노출조건과 비교하여 경미한 고온노출조건이다. 고온에서와 고온노출 후 GFRP 보강근의 인장강도와 탄성계수를 비교하였다. 실험결과, 고온에서 GFRP 보강근의 인장성능이 감소하는 것으로 나타났으나, 고온노출 후 보강근의 인장성능은 거의 고온노출전의 수준으로 회복되는 것으로 나타났다. 이와 같은 결과는 화재로 손상 받은 GFRP 보강 콘크리트 구조물의 평가를 위하여 중요한 자료가 된다.

• Corrosion Science and Technology
• /
• 제22권3호
• /
• pp.175-186
• /
• 2023

Effects of high-temperature environment and low-temperature environment on corrosion behaviours of 18Cr stainless steels (type 304L, type 441) in simulated selective catalytic reduction (SCR) environments were studied using weight loss test in each environment and rust analysis. With time to exposure to the high-temperature environment, type 441 was more resistant to corrosion than type 304L due to both higher diffusivity of Cr and lower thermal expansion coefficient in α-iron. The former provides a stable protective Cr₂O₃ layer. The latter leaded to low residual stress between scale and steel, reducing the spallation of the scale. With time to exposure to the low-temperature environment, on the other hand, type 304L was more resistant to corrosion than type 441. The lower resistance of type 441 was caused by Cr-depleted zone with less than 11% formed during the pre-exposure to a high-temperature environment, unlike type 304L. It was confirmed by results from the crevice corrosion test of sensitised 11Cr steel. Hence, to achieve higher corrosion resistance in simulated SCR environments, ferritic stainless steels having lower thermal expansion coefficient and higher diffusivity of Cr but containing more than 18% Cr are recommended.

• 연구논문집
• /
• 통권31호
• /
• pp.157-163
• /
• 2001

Evolution of microstructure due to service exposure to high temperature has a strong effect performance of heat resistant steels. In case of modified 9Cr-1Mo steels, precipitation of $Fe_2Mo$-type laves phases and coarcening of $M_23C_6$-type carbides is the primary cause of degradation of mechanical properties such as creep resistance, tensile strength and toughness. Creep tests have been carried out on pre-aging mod. 9Cr-1Mo steels to examine the effect of pre-aging and stress on the creep strength. Based on the results, a nondestructive procedure, where electrochemical technique that quantitatively detect laves phases and $M_23C_6$-type carbides in a material is used, has been proposed to evaluate a residual creep life of mod. 9Cr-1Mo steels.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.148.2-148.2
• /
• 2013

We prepared hydrophobic PDMS-coated porous silica as pre-concentration adsorbent for chemical warfare agents (CWAs). Since CWAs can be harmful to human even with a small amount, detecting low-concentration CWAs has been attracting attention in defense development. Porous silica is one of the promising candidates for CWAs pre-concentration adsorbent since it is thermally stable and its surface area is sufficiently high. A drawback of silica is that adsorption of CWAs can be significantly reduced due to competitive adsorption with water molecule in air since silica is quite hydrophilic. In order to solve this problem, hydrophobic polydimethylsiloxane (PDMS) thin film was deposited on silica. Adsorption and desorption of chemical warfare agent (CWA) simulants (Dimethylmethylphosphonate, DMMP and Dipropylene Glycol Methyl Ether, DPGEM) on bare and PDMS-coated silica were studied using temperature programed desorption (TPD) with and without co-exposing of water vapor. Without exposure of water vapor, desorbed amount of DMMP from PDMS-coated silica was twice larger than that from bare silica. When the samples were exposed to DMMP and water vapor at the same time, no DMMP was desorbed from bare silica due to competitive adsorption with water. On the other hand, desorbed DMMP was detected from PDMS-coated silica with reduced amount compared to that from the sample without water vapor exposure. Adsorption and desorption of DPGME with and without water vapor exposing was also investigated. In case of bare silica, all the adsorbed DPGME was decomposed during the heating process whereas molecular DPGME was observed on PDMS-coated silica. In summary, we showed that hydrophobic PDMS-coating can enhance the adsorption selectivity toward DMMP under humid condition and PDMS-coating also can have positive effect on molecular desorption of DPGME. Therefore we propose PDMS-coated silica could be an adequate adsorbent for CWAs pre-concentration under practical condition.

• Environmental Engineering Research
• /
• 제15권4호
• /
• pp.225-230
• /
• 2010

In order to treat soil contaminated with high percentages of water and petroleum, the combined microwave and thermal desorption process was studied, which was composed of the consecutive connection of two pre-treatment processes. For the thickness of the contaminated soil layer on the transfer conveyor belt, the optimal total petroleum hydrocarbon (TPH) removal rate was studied with respect to the duration of microwave exposure in the consecutive process combined with thermal desorption. The TPH removal rate when the contaminated soil layer thickness was 1 cm at 6 kW of microwave power was 80%. The removals rates for 2 and 3 cm soil layer thicknesses were both 70%. Under identical experimental conditions, the TPH removal rate for the microwave pre-treatment, when considering the soil particle size, was over 70%. The lowest TPH removal rate was achieved with a particle diameter of 2.35 mm. For contaminated soil with 30% water content, 6 kW and a thermal desorption temperature of $600^{\circ}C$ were the optimal operational conditions for the removal of THP. However, considering the fuel consumption cost, 4 kW and a thermal desorption temperature of $300^{\circ}C$ would be the most economic conditions.

• 대한금속재료학회지
• /
• 제49권1호
• /
• pp.25-31
• /
• 2011

Solid oxide fuel cells (SOFCs) have many attractive features for widespread applications in generation systems. Recently, stainless steels have attractive materials for metallic bipolar plate because metallic bipolar plates have many benefits compared to others such as graphite and composite bipolar plates. SOFC operates on high temperature of about $800{\sim}1000^{\circ}C$ than other fuel cell systems. Thus, many studies have attempted to reduced the operation temperature of SOFC to about $600{\sim}800^{\circ}C$, which is the intermediate temperature (IT) of SOFC. Low cost and high-temperature corrosion resistance are very important for the practical applications of SOFC in various industries. In this study, two specimens, 304 and 430 stainless steels with and without different pre-surface treatments on the surface were investigated. And, specimens were exposed at high temperature in the box furnace under oxidation atmosphere of $800^{\circ}C$. Oxidation behavior have been investigated with the materials exposed at different times (100 hrs and 400 hrs) by SEM, EDS and XRD. By increasing exposure time, the amount of metal oxide increased in the order like; STS304 < STS430 and As-received < As-polished < Sand-blast specimens.

• 마이크로전자및패키징학회지
• /
• 제25권4호
• /
• pp.53-58
• /
• 2018

집적회로 소자의 축소가 물리적 한계에 도달 한 이후 3D 패키징, 임베디드 패키징 및 팬 아웃 웨이퍼 레벨 패키징(FOWLP, fan-out wafer level packaging)과 같은 혁신적인 패키징 기술들이 활발히 연구되고 있다. 본 연구에서는 FOWLP의 다층 재배선(redistribution layer)에 사용하기 위한 유무기 하이브리드 유전체 소재의 공정을 평가하였다. 폴리이미드(PI) 또는 폴리파라페닐렌벤조비스옥사졸(PBO)과 같은 현 유기 유전체와 비교하여 폴리실세스키옥산(polysilsesquioxane, PSSQ)라고 불리는 유무기 하이브리드 유전체는 기계적, 열적 및 전기적 안정성을 향상시킬 수 있고, UV 노광을 통하여 경화 공정과 패턴 공정을 동시에 할 수 있는 장점이 있다. 폴리실세스키옥산 용액을 6 인치 Si 웨이퍼에 스핀 코팅한 후 pre-baking과 UV 노광 공정을 이용하여 패턴 및 경화를 진행하였다. 10분의 UV 노광 시간으로 경화와 $2{\mu}m$ 라인 패턴 형성이 동시에 진행됨을 확인하였고, 경화된 폴리실세스키옥산 유전체의 유전상수는 2.0에서 2.4 로 측정되었다. 폴리실세스키옥산 소재를 이용하여 고온 경화 공정없이 UV 노광 공정만으로 경화와 패턴을 할 수 있는 공정 가능성을 보였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1533-1535
• /
• 2002

Carbon nanotubes (CNTs) were grown with high density on a large area of Ni-coated silicon oxide substrates by using an inductively coupled plasma-chemical vapor deposition (ICP-CVD) of $C_2H_2$ at temperatures ranging from 600 to $700^{\circ}C$. The Ni catalyst was formed using an RF magnetron sputtering system with varying the operating pressure and exposure time of $NH_3$ plasma. The surface morphology of nickel catalyst films and CNTs was examined by SEM and AFM. The graphitized structure of CNTs was confirmed by Ramman spectra, SEM, and TEM. The growth of CNTs was observed to be strongly influenced by the surface morphology of Ni catalyst, which depended on the pre-treatment time and growth temperature. Dense CNTs with uniform-sized grains were successfully grown by ICP-CVD.