• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.19-20
• /
• 2014

Boiler design should be desinged to maximize thermal efficiency of the system under imposed load requirement and a boiler should be validated for transient operation. If a proper prediction is possible on the transient behavior and transient characteristics of a boiler, one may asses the performance of boiler component, control logics and operation procedures. In this work, dynamic modeling method of boiler is presented and dynamic simulation of load runback scenario was carried out on suprecritical oil-firing boiler.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.522-523
• /
• 2015

This paper proposes a deadbeat current controller using predictive current method for three-phase shunt active power filter (SAPF). In proposed controller, the compensating current reference which is necessary for the deadbeat control is estimated by using the predictive current method. This method can improve the accuracy of compensation and ensure the fast dynamic response of SAPF. Simulations have been carried out to demonstrate the perfomance of SAPF using proposed control method.

• Korean Journal of Hydrosciences
• /
• v.3
• /
• pp.81-96
• /
• 1992

This study represents the methodology for feasibility analysis of small hydro power SHP plant. Cumulative density function of Weibull distribution and Thiessen method were adopted to decide flow duration curve at SHP candidate site. The perfomance prediction model and construction cost estimation model for tunnel-type SHP plant were developed. Eight tunnel -type SHP candidate sites existing on Han-river were selected and surveyed for actual site reconnaissance. The performance characteristics and economical feasibility for these sites were analyzed by using developed models. As a result, it was found that the optimum design flowrate with the lowest unit generation cost for tunel-type SHP candidate site were the flowrate concerming with between 20% and 30% of time ratio on the flow duration curve. Additionally, primary design specifications such as design flowrate, effective head, capacity, annual averageload factor, annual electricity production were estimated and discussed for eight surveyed SHP candidate sites.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.494-497
• /
• 2012

A methodology to predict the output performance of small hydro power using treated effluent in wastewater treatment plant has been studied. Existing plant located Kyunggi-Do were selected and the output performance characteristics for these plants were analyzed. As a result, it was found that the developed model in this study can be used to analyze the output characteristics for small hydro power in wastewater treatment plant. Additionally, primary design specifications such as design flowrate, capacity, operational rate and annual electricity production were estimated and discussed.

• Journal of Power System Engineering
• /
• v.19 no.6
• /
• pp.33-38
• /
• 2015

In this study new CVT(Continuously Variable Transmission) system which is adaptable to a small size electric vehicle is proposed available to gradient response CVT. New pulleys consist of springs adapted driving pulley and driven pulley. At the moment a small electric vehicle drive a slope, new system respond to a gradient as overcoming tensional force of springs. We made prototype of gradient response CVT to test parts performance and travelling performance test. As a result of test, belt pitch diameter varied for high torque direction at the gradient. In the flat travelling, acceleration travelling and gradient travelling performance test, the small electric vehicle with gradient response CVT get improved perfomance than the small electric vehicle with reduction gear.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.1007-1009
• /
• 2010

실험을 통하여 엔진의 성능을 파악하고자 한다면 적지 않은 시간동안 많은 비용과 노력이 필요하다. 최근 연구에서는 이러한 단점을 해결하기 위해 CFD를 이용 선행해석을 통해 미리 그 엔진의 성능을 예측하여 실험에 들이는 시간과 비용을 줄여가고 있다. 본 연구는 실험을 통하여 소형엔진의 성능을 알아보기 이전에 선행해석을 통해 소형엔진의 성능을 예측하고자 한다. 소형엔진의 선행 해석을 위해 전자제어 연료분사 방식의 400cc급 소형엔진을 모델링하고 1D 해석프로그램인 GT-Power를 통하여 엔진의 Toque, Power 및 배기가스를 예측하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.870-875
• /
• 2015

Diesel engines are widely used due to superior power and fuel consumption, however there are many challenges in exhaust gas management. Exhaust gas recirculation (EGR) is the most effective technique for reducing mono-nitrogen oxide (NOx) emissions in a diesel engine, in comparison with other catalytic technologies. In addition, the technology has a number of advantages in terms of economic efficiency and implementation. In this study, the effects on the power and exhaust characteristics of diesel engines equipped with EGR systems were investigated. It was found that as the EGR rate increased, horsepower expressed as IHP and BHP decreased. The net effect of the application of EGR was measured at various engine speeds. EGR technology caused decreases in BHP of around 9% during low engine speed and 3.5% during high engine speed. Additionally, NOx emissions reduced as the EGR rate increased, and increased as engine speed increased. However, smoke emissions increased as the EGR rate increased, and decreased as engine speed increased. The optimum operating conditions and ERG rate to simultaneously achieve minimum NOx and smoke emissions were investigate. It was found that as the EGR rate increased, optimal operating speed for minimal NOx and smoke also increased. Keywords: Diesel engine, Exhaust gas recirculation, Power perfomance, Emission characteristics, NOx, Smoke

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.1
• /
• pp.145-151
• /
• 2010

This paper presents the design and implementation of direction controllers by microstep control and dc servo control for material transport system. The perfomances of direction control systems are compared in position responses and motor power consumptions between microstep control of a step motor and dc servo control.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.166-170
• /
• 1998

The metal transfer of CO2 arc welding machine can be devided into short-circuit(low current) metal transfer. Especially in large crrent region, the main problem of CO2 arc welding machine is much spatter generation which is caused by mainly instant short-circuit matal transfer. So in this paper descrives new current control method in large current region, which can improve welding performance and lessen spatter generation. And as a result of experiment, the effect of proposed control method is demonstrated.

• Tribology and Lubricants
• /
• v.13 no.3
• /
• pp.73-84
• /
• 1997

ER clutch is a device using ER fluid, so called "intelligent material" and is a controlled system with electric field strength. Currently, the temperature of ER fluid increases and affects the performance of ER clutch when ER clutch is operating. This study was undertaken to estimate this performance variation due to temperature rise of ER fluid. An analytic heat transfer model of concentric cylinder type ER clutch was developed and with this model, effects of changing geometric, kinetic parameters of ER clutch and ER fluid properties were described. In conclusion, compared with neglecting thermal effects, a performance of ER clutch was very differential and for uniform performance of ER clutch, we have to improve thermal stability of ER fluid. ER fluid.