• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.2
• /
• pp.125-131
• /
• 2003

In this paper Power Flow Finite Element Method(PFFEM) has been implemented to analyze the vibration of a plate in mid and high frequency ranges. In order to solve the vibration energy governing equation in Power Flow Analysis(PFA), The Finite Element Method(FEM) was used as a numerical tool. It allowed one to predict the distribution of displacement and Intensity in the plate vibrating at mid and high frequencies. The results were compared with the analytical solutions and the approximate FEM solutions. The comparison showed that PFFEM can be an effective tool to analyze the structural vibration in mid and high frequency ranges.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.11A
• /
• pp.1113-1119
• /
• 2007

In this paper, first, we proposed various possible candidate schemes for determining initial sleep window size and varying sleep window size in sleep mode for power saving class I of IEEE 802.16e. Then, we analyzed and compared the power saving performances of those schemes. The schemes used for the comparisons are EICV of IEEE 802.16e, and other comparable schemes such as EIED, EILD, LIED and LILD. Experimental results show that LILD and EIED outperform other comparable schemes. Especially, EIED shows the better performances for the case of high traffic intensity environments, while LILD does for the low traffic intensity case.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.49 no.8
• /
• pp.412-417
• /
• 2000

TV ghost interference can be described as passive interference by the conducting part of transmission lines. In order to survey this interference from large-sized overhead EHV (extra high voltage) transmission line, TV reception quality was measured in the vicinity of that before and after construction. Instrumentation system was composed of ghost analyzer, TV received field intensity meter, VHF/UHF antennas, TV monitor and so on. The system is installed inside the vehicle. TV field intensity and PDUR (Perceived Desired wave to Undersired wave Ratio) are measured to evaluate TV ghost by using the system and vehicle. As the results, the useful data, which can be used to evaluate the effect of TV ghost interference from transmission lines could be obtained. In this paper, it is shown that the range of TV ghost interference from transmission lines can vary according to the frequency of TV electromagnetic wave, an incidence angle to the line and the other conditiions. At present, we are making efforts to establish a PDUR guideline for transmission lines.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.8
• /
• pp.961-969
• /
• 2007

The laser material processing has replaced a conventional material processing such as a welding, cutting, drilling and surface modification and so on. LTH(Laser Transformation Hardening) is one branch of the laser surface modification process. A lot of energy is needed for the LTH process to elevate workpiece surface to temperature of the austenite transformation($A_3$), which results from utilizing a beam with a larger size and lower power intensity comparatively. The absorptivity of the laser energy with respect to material depends on the wave length of a beam. This study is related to the surface hardening for the rod-shaped carbon steel by the high power diode laser(HPDL) whose beam absorptivity is better than conventional types of lasers such as $CO_2$ or Nd:YAG laser. Because a beam proceeds on the rotating specimen the pretreated hardened-phase can be tempered and softened by the overlapping between hardened tracks. Accordingly, the longitudinal hardness measurement and observation of the micro structure was carried out for an assessment of the hardening characteristics. In addition, a hardening characteristics as a hardenability of materials was compared in the point of view of the hardness distribution and hardening depth and width.

• Journal of Korean Physical Therapy Science
• /
• v.10 no.1
• /
• pp.198-205
• /
• 2003

We evaluated the effect of low power GaAsAl laser on re-epithelization in full-thickness excisional wound of rat skin. Two full-thickness excisions were made on the back of the experimental animals. Low power laser applications with 10mW intensity were treated experimental animals twice a day for 7 days. On the seventh postoperative day the quantitative analysis of re-epithelization was performed using immunohistochemical staining for proliferating cell nuclear antigen (PCNA). The majority of PCNA immunoreactive cells was observed at epithelial cells in the margin of full thickness excisional wound. The low power laser treatments significantly increased the number of PCNA immunoreactive cell as compared to that of non treated animal group (p<0.01). The shape of PCNA immunoreactive cell appeared as small dark, round to ovoid structures. Most PCNA immunoreactive cells exhibited a high intensity of staining that contrasted sharply with the surrounding background. In conclusion, these findings suggest that GaAlAs laser treatments effectively enhance the epithelial wound healing by the stimulating cell proliferation. Furthermore, the majority of cell proliferation occurred in the margin of full thickness excisional wound.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1181-1182
• /
• 2006

The solar power system comprises a solar battery that directly converts light energy to electrical energy with a photovoltaic effect and a power converter system, that is, inverter that converts direct current power, which is generated from solar battery to common alternating current. In this paper, database was constituted through remote monitoring supervision measurement for the long-time positive operation of 3kW solar power system installed within the solar energy positive research complex of Chosun University. As a result of analyzing the reduction of the efficiency of solar battery and inverter that are compositional components of PV system through an analysis on the acquired data, the PV output was proven over 65% of the total output when insolation intensity exceeded 600W/m2 in 2005, and the array conversion efficiency dropped much more than rating; meanwhile, insolation intensity dropped below 600W/m2. Therefore, it has been demonstrated that approximately 35% of the entire amount of PV output operated under the condition that the inverter efficiency rate dropped rapidly by 60 to 70%.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.6
• /
• pp.94-101
• /
• 2004

From the Beckmann's reflection model of wave incident, reflected light from a surface is known to have not only specular but also diffuse components. The specular component dominant a surface for a mirror-like surface is distributed on the almost the same area as the spot on the surface, but the diffuse component region dominant f3r a rough surface spreads scattered on the larger areas than the spot. Therefore, statistic parameters from the scattered light distribution are more meaningful in the diffuse region, while the magnitude of rather meaning in the specular region. In usual, there need two sensors to acquire two kinds of information: Photo-detector for light intensity magnitude and image sensor for light intensity distribution. But dual sensor scheme requires a beam splitter usually to feed light to each sensor, and moreover there is not a combination rule to relieve the different sensor characteristics. In this study a new method is proposed for acquisition of the dual information using only an image sensor. Specular region is established on an image area being distinguished from a diffuse component, and laser power is adjusted so that no pixel of the image sensor in the specular region is saturated. Simulation based on the light reflection theory and the experimental results are quite well matched, and thus the proposed method was proved to be very useful for mirror-like surface measurement.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.1
• /
• pp.33-41
• /
• 2023

Recently, global warming has accelerated climate change, increased extreme weather phenomena, and increased the frequency and intensity of weather disasters, leading to increasing uncertainty about the power production of new and renewable energy that is sensitive to weather. In fact, it has been reported that a number of damage to hydroelectric power generation have occurred due to weather disasters. Therefore, using the hydroelectric power generation performance data of Chungju Dam, meteorological data of Chungju Meteorological Observatory, and operation data of Chungju Dam, this study investigated the effect of meteorological disasters on hydroelectric power generation through structural equation modeling considering the number and intensity of meteorological disasters per month. The results indicated that the increased drought occurrence affected the decreased hydroelectric power generation by about 38.3 %, however the increased hydroelectric power generation could not explained by the increased flood occurrence. In conclusion, an increased drought occurrence in future may significantly influence hydroelectric power generation.

• Current Optics and Photonics
• /
• v.8 no.4
• /
• pp.355-365
• /
• 2024

Wavefront coding (WFC) imaging systems can redistribute the energy of an interference laser spot on an image plane sensor by wavefront phase modulation and reduce the peak intensity, realizing laser protection while maintaining imaging functionality by leveraging algorithmic post-processing. In this paper, a spiral axicon WFC imaging system is proposed, and the performance for laser protection is investigated by constructing a laser transmission model. An Airy disk on an image plane sensor is refactored into a symmetrical hollow ring by a spiral axicon phase mask, and the maximum intensity can be reduced to lower than 1% and single-pixel power to 1.2%. The spiral axicon phase mask exhibits strong robustness to the position of the interference laser source and can effectively reduce the risk of sensor damage for an almost arbitrary lase propagation distance. Moreover, we revealed that there is a sensor hazard distance for both conventional and WFC imaging systems where the maximum single-pixel power reaches a peak value under irradiation of a power-fixed laser source. Our findings can offer guidance for the anti-laser reinforcement design of photoelectric imaging systems, thereby enhancing the adaptability of imaging systems in a complex laser environment. The laser blinding-resistant imaging system has potential applications in security monitoring, autonomous driving, and intense-laser-pulse experiments.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3121-3126
• /
• 2013

The integrity evaluation of pipes in nuclear power plant are essential for the safety of reactor vessel, and integrity must be assured when flaws are found. Accurate stress intensity analyses and crack growth rate data of surface-cracked components are needed for reliable prediction of their fatigue life and fracture strengths. Fatigue design and life assessment are the essential technologies to design the structures such as pipe, industrial plant equipment and so on. The effect of crack spacing on stress intensity factor K values was studied using three-dimensional finite element method (FEM). For the case of cylinder under internal pressure, a significant increase in K values observed at the deepest point of the surface crack. Also, this paper describes the fatigue analysis for cracked structures submitted to bending loads.