• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.70-77
• /
• 1999

A miniaturized voltage controlled oscillator using multi-layer ceramic technology at PCS frequency band is designed and fabricated. To improve the phase noise characteristics and to reduce the size, the strip line which is embedded in a high performance multi-layer ceramic substrate is used as an inductor of VCO. And the fabricated VCO is very small size ($6mm\times6mm\times2mm$). At the bias condition of 3.3 V and 9mA, the output power and phase noise in the operating frequency range of 1,720~1,780 MHz are -3.7 dBm and -95 dBc/Hz at 10 KHz offset from the carrier, respectively. The phase noise and size are better than the conventional VCO using glass epoxy substrate.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.8 no.4
• /
• pp.25-30
• /
• 1971

Fabrication and measurements of the magnetically tunable YIG band pass or stop filter at X-band are discussed. Using two YIG spheres located at the region of r-f circularly polarized magnetic field between the strip lines, the pass or stop characteristics of the filter are obtained. In the case of band stop, the output level is typically 25db lower than the input power. Contrarily for the pass band, the pass band level is 22db higher than the stop frequency region. The experimental results are in good agreement with the theoretical values of FMR. Further it is shown that the structure can be used for a directional coupler.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.12
• /
• pp.1238-1245
• /
• 2007

A very abnormal vibration was occurred at the LP(low pressure) turbine continuously during the pre-operation for a 550MW class USC(ultra super critical) steam turbine. This vibration was initiated at the rotating speed of about 3,450 rpm and then the vibration amplitude was highly increased the number by $2{\sim}3$ times with the increase of the rotating speed to the rated speed (3,600 rpm). In this paper, this abnormal vibration named spike vibration. This spike vibration was caused by the rubbing between the rotating bucket tip seal and the lower half of spill strip. Also, this paper presents the mechanism of the spike vibration and the proper method to eliminate this abnormal vibration problem. This result would be good practice to find the solution of similar high vibration in the USC steam turbines for power plant as well as industrial rotating machineries.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.12
• /
• pp.1252-1259
• /
• 2009

Due to the international competition and global pressure, the roll speed is increased. However, higher speeds increase the power density in the process as well as the plant's potential to react with vibrations. Under certain operating conditions, vibrations may occur, which again cause chattermarks, strip rupture or coil break fault. The appropriate condition monitoring is needed to improve product quality and availability. The aim of condition monitoring is to reduce maintenance costs, increase productivity and improve product quality. This paper proposes a condition monitoring tool designed for the classification of coil break fault. This method is used to cold rolling mill for faults monitoring based on vibration and motor current signals. The results show that the performance of classification has high accuracy based on experimental work.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.5
• /
• pp.48-57
• /
• 1994

The specific power output and thermal effeciency of any two-stroke engine are dependent on its scavenging behavior. Among the many factors which influence on the scavenging process, the cylinder head shape is one of the important factor. Hence in this study three different type models of cylinder head shape which are the cylindrical, the spherical and the arbitrary shape are studied to show the effects of the turbulent scavenging process in the cylinder with one inlet port, two side ports and one exhaust port. A modified version of KIVA-II which strip out of or add planes of cells across the mesh above the piston for flow simulation of two-stroke engine is used. The $k-{\varepsilon}$ turbulent model is used. The results show that the flow in a two-stroke engine cylinder of the spherical head shape among the three different type model is a desirable for efficient scavenging.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1286-1291
• /
• 2003

Quench behavior of resistive superconducting fault current limiters (SFCLS) with various pattern shapes was investigated. The pattern shapes employed were meander, bi-spiral, and spital shapes of identical line width, gap and margin. SFCLS were fabricated from YBCO thin films grown on two-inch diameter Al$_2$O$_3$ substrates under the same conditions. The total length of current limiting paths was the shortest at the spital shape due to its larger useless space. Inductance component of SFCLs with the spiral shape was around two times as high as those of other two shapes. This is not desirable since impedance characteristics of existing power systems can be changed. Resistance rise of current limiting elements was low at a spiral shape before the whole quench completion, which may act as a disadvantage for simultaneous quench in serial connection between current limiting elements, but the temperature tended to have similar values at higher voltages. On the other hand, hi-spital shape was severe at insulation level between current limiting lines. When these aspects were considered, we concluded that a meander shape was appropriate to design for a resistive SFCL based on thin films except the concentration of electric field at edge areas of strip lines.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.11A
• /
• pp.921-928
• /
• 2003

This paper propose a new design of directional couplers with the high directivity. The directional coupler is used to check and verify the power, frequency and antenna reflection of a signal at transmission station for the mobile communications. The performance index of the directional coupler is to which the coupling is strong to reduce the effect on the transmitted power and the directivity is high to suppress the interference of the reflected signals and reduce the nor in the communication. Then, the architectures to gain the high directivity and the studies to get the strong coupling have been proposed However, the conventional architectures lot the high directivity and strong coupling have the directivity by about 20㏈ and the difficulty to achieve the higher directivity than 40㏈ suitable for IMT-2000 [1]. This paper proposes an architecture of the directional coupler which is based on the grounding composed of the strip lines and the comparison results with the conventional directional couplers. The comparison results show that the proposed directional coupler has the directivity more than 40 ㏈ and is adequate for the 2.05GHz IMT-2000

• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.466-475
• /
• 1997

In this paper, an implantable middle ear hearing aids using an electromagnetic transducer which consists of a tiny coil and a magnet is designed, and objective design method to implement a vibrator of the electromagnetic type transducer is proposed. Sound characteristic of the electromagnetic type vibrator is excellent but power transfer rate is lower than that of a ceramic type. To improve power transfer efficiency of system, external and inner part of a middle ear system is designed using FM transmission method. We implemented an experimental set of the designed transducer, inner part, and outer part. Then, we measured vibration characteristics of a metal strip and a temporal bone of a dead body. As the results, we confirmed the advantage of FM method and showed that designed transducer could effectively transmit vibration of amplified input sound pressure to ossicle.

• Polymer(Korea)
• /
• v.33 no.1
• /
• pp.91-95
• /
• 2009

We fabricated the electromagnetic (EM) noise absorber films for high temperature use by blending a soft magnetic powder with poly(amide imide) (PAI). The EM noise absorber films of PAI/soft magnet composite were prepared by casting the solution of poly(amide amic acid)/soft magnet powder into glass substrate with casting applicator device and then thermal imidization. The obtained films were fully characterized and their physical properties including thermal behavior, thermal stability and mechanical properties were studied. The EM noise absorption ability was also investigated using micro-strip line method. At 1 GHz, the power loss of composite film with 150 ${\mu}m$ thickness was about 25%.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.7
• /
• pp.1160-1164
• /
• 2008

This paper presents an wideband stripline balun. And, the proposed balun is composed of one power divider and two phase converters on stripline substrate. The target characteristics of the proposed balun is the combination loss of below -0.05 dB, an amplitude imbalance of ${\pm}0.5\;dB$ and a phase imbalance of $180{\pm}10$ degrees, with the reflection coefficient(S11) of below -10 dB over frequencies ranging from 500 to 1500 MHz. The fabricated balun occupies the area of $12(W){\times}220(L){\times}2.3(T)\;mm3$. Experimental measurement shows that the fabricated balun has an amplitude imbalance of ${\pm}0.7\;dB$, a phase imbalance of $180{\pm}8$ degrees and an insertion loss of about -2 dB with the reflection coefficient(S11) of below -10 dB over frequencies ranging from 500 to 1,500 MHz.