• 시스템엔지니어링학술지
• /
• 제14권1호
• /
• pp.1-12
• /
• 2018

In the energy-guzzling industries such as steel making and cement, power plants utilizing waste heat have been attracting attention to increase energy efficiency. However, the existing economic analysis system doesn't consider the special working fluids and the cost models of the main equipment used in the waste heat recovery power plant. So it is difficult to estimate the plant economics accurately. Therefore, It is required to develop a economic analysis module that can more accurately evaluate for the power plant. In this study, the systems engineering approach was used to design and develop the module that systematically reflects the characteristics of the power plant and various requirements. Specifically, first, the special working fluids and main equipment applied to the power plant were investigated. Next, the cost models for each equipment were developed. Finally, the economic analysis module based on this was developed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 학술대회 논문집 정보 및 제어부문
• /
• pp.231-233
• /
• 2005

For the low-power design of the mobile multimedia system architecture, this paper modeling the mobile multimedia system and analysis the power consumption profile about the whole communication environment. The mobile system model consist of air interface, RIP front-end, base-band processing module and human interface. For the result of power consumption profile analysis, the power consumption of multimedia processing is above 60% compare to the whole power consumption in mobile multimedia system. To minimize the power consumption in processing module which consumes the large power, this paper proposed the Microscopic DVS technique which applies the optimum voltage for the each multimedia frame. For the simulation result, proposed power minimization technique reduce the power consumption about 30%.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.1144-1149
• /
• 2006

Electric power is generated by Seeback Effect if there is thermal difference in pettier module. Peltier module is composed by alumina, Bi-Te semiconductor and insulation (or air). If load is increased in pettier module, the alumina of module will be destroyed. One of the preventing method of module destruction is using damper between module and heat source. But the electric Power is dropped because of decrease of thermal difference, if thermal conductivity of damper was tourer than other thermoelectric materials. We design, Polymer Pad for enhancing thermoelectric porter. As the result of these experiment, Polymer Pad is more superior than the Rubber in the stability and thermal conduction.

• 디지털콘텐츠학회 논문지
• /
• 제17권3호
• /
• pp.173-180
• /
• 2016

본 논문에서는 종래의 보안관리 시스템과 송수신 모듈의 단점을 개선하기 위해 유무선 복합기능의 송수신 모듈과 이를 사용한 신뢰성 높은 실시간 보안시스템을 제안한다. 제안하는 복합 송수신모듈은 RF 제어 회로와 무선 송수신 회로로 구성된다. RF제어회로는 저전력 협대역 RF 송수신 시스템으로서 마이크로프로세서의 레지스터에 저장되어 있는 특정 주파수 대역을 불러올 수 있고, 임의로 값을 쓰거나 읽어 들여 임의 주파수의 송신출력을 사용자가 제어할 수 있도록 설계한다. RF 송신 모듈의 동작을 위한 구동 알고리듬을 제시하고 설계한 복합 송수신 모듈과 동작 알고리듬을 시작품으로 구현하여 실험을 통해 유효성을 확인한다.

• 전력전자학회논문지
• /
• 제24권5호
• /
• pp.379-387
• /
• 2019

A bidirectional flyback converter is a suitable topology for use in a PV-to-bus differential power processing (DPP) module for PV applications due to its electrical isolation capability, bidirectional power transfer, high step-up ratio, and simple circuit structure. However, the bidirectional flyback converter design should consider the effect of the output-side power switch utilized for bidirectional operation compared with that of the conventional flyback converter. This study presents the structure and design methodology of the bidirectional flyback converter for a PV DPP module. Magnetizing inductance is designed by calculating the power loss of converter components within the rated load range under the discontinuous conduction mode, which is unaffected by the reverse recovery characteristics of the anti-parallel diode of the output-side power switch. The validity of the proposed design methodology is verified using a 25 W bidirectional flyback converter prototype. The operational principles and the performance of the DPP operation are verified using practical DPP modules consisting of bidirectional flyback converters implemented according to the proposed design methodology.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권7호
• /
• pp.876-884
• /
• 2012

The worldwide CPV(Concentrated Photo Voltaic) market has been increased rapidly due to the increase in large-scale PV(Photo Voltaic) plants which are situated in sun-rich areas with either a Mediterranean or equatorial-type climate. CPV systems are arguably some of the most important devices in the production of electricity within regions with a sun-rich climate, particularly those which benefit from abundant direct solar irradiation. We have developed a 500X CPV module with rated power of 170Wp. The CPV module must satisfy the constraint of having a sensitive tracking accuracy due to the limited tolerance of the acceptance angle in intrinsic optical design. In this study, the module's acceptance angle used was designed with a tolerance angle of ${\pm}1^{\circ}$ in the secondary optics design. In general, non-concentrated module type 2-axis trackers have a tolerance angle larger than ${\pm}1^{\circ}$ due to standard silicon-type modules which are insensitive to the tracking accuracy of the sun. They have a tolerance angle of ${\pm}2{\sim}4^{\circ}$, which fails to exert a significant influence on the performance of the module. This paper provides a study of an experimental variation of the efficiency of the CPV module in terms of its tracking accuracy. Also, the performance of the module is studied from the perspective of temperature and direct irradiation.

• Nuclear Engineering and Technology
• /
• 제52권2호
• /
• pp.323-327
• /
• 2020

In this study, the neutronic calculation to obtain tritium breeding ratio (TBR) in a deuterium-tritium (D-T) fusion power reactor using Monte Carlo MCNPX is done. In addition, by using COMSOL software, an efficient cooling system is designed. In the proposed design, it is adequate to enrich up to 40% ⁶Li. Total tritium breeding ratio of 1.12 is achieved. The temperature of helium as coolant gas never exceed 687℃. As regards the tolerable temperature of beryllium (650℃), the design of blanket module is done in the way that beryllium temperature never exceed 600℃. The main feature of this design indicates the temperature of helium coolant is higher than other proposed models for blanket module, therefore power of electricity generation will increase.

• 반도체디스플레이기술학회지
• /
• 제19권3호
• /
• pp.118-123
• /
• 2020

In this paper, the design method of asynchronous nonvolatile memory module that can efficiently process and store large amounts of data without loss when the power turned off is proposed and implemented. PSRAM, which takes advantage of DRAM and SRAM, was used for data processing, and NAND flash memory was used for data storage and backup. The problem of a lot of signal interference due to the characteristics of memory devices was solved through PCB design using high-density integration technology. In addition, a boost circuit using the super capacitor of 0.47F was designed to supply sufficient power to the system during the time to back up data when the power is off. As a result, an asynchronous nonvolatile memory module was designed and implemented that guarantees reliability and stability and can semi-permanently store data for about 10 years. The proposed method solved the problem of frequent data loss in industrial sites and presented the possibility of commercialization by providing convenience to users and managers.

• 한국정보시스템학회지:정보시스템연구
• /
• 제28권1호
• /
• pp.115-132
• /
• 2019

Purpose The purpose of this study is to explain the agrophotovolatic system built by the Korea South-East Power Company and to propose methods to activate the agrophotovolatic system for the development of the renewable energy industry. Design/methodology/approach We conducted a three-step simulation in order to design a photovoltaic module, and we built the agrophotovolatic system based on the results of the simulation. Then, we analyzed the monthly generation of power and the rice harvests produced on farmland using the photovoltaic module. Based on the results of the analysis, we proposed institutional improvements to increase the use of the agrophotovolatic system, and we proposed new business models to increase the participation of farmers and business persons. Findings When we compared the agrophotovolastic system with the general photovoltaic system, we found that the agrophotovoltaic system had higher utilization rates and power generation. An analysis of rice produced on farmland using the photovoltaic module showed that more than 80% of the rice produced on general farmland was harvested. We suggested activation plans that involved the revision of the farmland law and the introduction of renewable energy certificate (REC). We also proposed a land lease model and a farmer participation model as two new business models, and we conducted economic evaluations and sensitivity analyses for both models.

• 전기학회논문지
• /
• 제58권8호
• /
• pp.1572-1579
• /
• 2009

In this dissertation ultra-broadband power amplifier(UPA) was designed and fabricated using negative feedback technique. UPA was made of pre-amplifier, drive amplifier and power amplifier. Negative feedback technique was used to achieve ultra-broadband performance. Designed power amplifier has 30dB gain and 2W output power. The load-pull data of power amplifier for optimal power matching was extracted from the measured S-parameter. Fabricated PCB material, permittivity is 4.6 and thickness is 0.8mm, is FR4 and UPA was fabricated 3 modules for comparison of the simulated and measured results. Size of the fabricated pre-amplifier and drive amplifier module is 40mm'50mm'16mm. And from the experimental results, gain of the pre-amplifier module is 9.87dB at 2GHz and flatness is 0.63dB. Experimental result of the drive amplifier module is 10.97dB at 2GHz and flatness of that is 0.26dB. Test result of the power amplifier module is 10.71dB at 2GHz and flatness is 0.72dB. Total size of the power amplifier is 45mm'134mm'16mm. According to the test results, gain of the UPA is 28.98dB at 2GHz and flatness is 1.68dB. Output power was 32.098dBm at 2GHz, 32.154dBm at 1GHz and 31.273dBm at 100MHz.