• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.4A
• /
• pp.214-218
• /
• 2012

In this paper, we reported on a high performance waveguide VCO(voltage controlled oscillator) for FMCW applications. The waveguide VCO consists of a GaAs Gunn diode, a varactor diode, and two bias posts with low pass filter(LPF). The cavity is designed for fundamental mode at 47 GHz and operated at second harmonic of 94 GHz center frequency. The developed waveguide VCO has 1.095 GHz bandwidth, 590 MHz linearity with 1.69% and output power from 14.86 to 15.93 dBm. The phase noise is under -95 dBc/Hz at 1 MHz offset.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2522-2525
• /
• 2001

Si PIN diodes are subject to be damaged from the exposure of fast neutron by displacement of Si lattice structure. The defects are effective recombination centers for carriers which migrate through the base region of the PIN diode when forward voltage is applied. It causes an increase in current and a decrease in resistivity of the diode. This paper presents the development of a neutron sensor based on displacement damage effect. PIN diodes having various structures were made bymicro-fabrication process, and neutron beam test was performed to identify neutron damage effect to the diode. From a result of the test, it was shown that the forward voltage drop of the diode, at a constant current, has good linearity for neutron dosage. Also it was found that the newton dosage can be measured by the pin diode neutron dosimeter with constant current power.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.5
• /
• pp.1035-1039
• /
• 2012

In this paper, we developed a 94 GHz waveguide VCO(voltage controlled oscillator) using a GaAs-based Gunn diode and a varactor diode. The cavity is designed for fundamental mode at 47 GHz and operated at second harmonic of 94 GHz. Bias posts for diodes operate as LPF(low pass filter) and resonator. The fabricated waveguide VCO achieves an oscillation bandwidth of 760 MHz. Output power is from 12.61 to 15.26 dBm and phase noise is -101.13 dBc/Hz at 1 MHz offset frequency from the carrier.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.6
• /
• pp.563-569
• /
• 2002

This paper proposes an inverter for the grid-connected photovoltaic system based on the transformer-less inverter. This system consists of a high frequency DC-DC converter, high frequency transformer, diode bridge rectifiers, a DC filter, a low frequency inverter, and an AC filter. The 20kHz switched high frequency converter is used to generate bipolar PWM pulse, and the high frequency transformer transforms its voltage twice, which is subsequently rectified by diode bridge rectifiers for a full-wave rectified 60 Hz sine wave power output. Even though the high frequency link system needs more power semiconductors, a reduced size, light weight, and saved parts cost make this system more comparative than other power conditioning systems due to elimination of 60Hz transformer.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.5
• /
• pp.279-283
• /
• 2014

In this paper, we present an economical and practical standard to install a bypass diode in a thin-film PV module. This method helps to reduce heat generation and to prevent module degradation due to excess current from reverse bias. The experimental results confirm that for different numbers of solar cells, there is a relation between the excess reverse current and the degradation of solar cells in a-Si:H modules. The optimal number of solar cells that can be connected per bypass diode could be obtained through an analysis of the results to effectively suppress the degradation and to reduce the heat generated by the module. This technique could be expanded for use in high power crystalline Si PV modules.

• Proceedings of the KIEE Conference
• /
• 2008.04c
• /
• pp.106-109
• /
• 2008

Piecewise linear diode models are widely used for large-signal circuit analyses, especially power electronic circuit simulations. When using a piecewise linear diode model for simulation, a switching method to select a proper one among linear models is needed. The conventional switching method keeps the previous ON, OFF state information, and applies different switching conditions according to the state. However, this method has difficulties especially in extending to multi-piecewise linear models. This paper presents a switching method which appropriately divides the v-i plane into regions and select a linear model according to the region where the operating point(the voltage and the current of the diode) belongs. This switching method is easily extended to multi-Piecewise linear models. An example using the tableau analysis and the backward Euler integration is presented for verification.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.769-772
• /
• 2008

For several years, many researchers have proposed LED backlight dimming technology for low power consumption and high contrast ratio. One of the major issues plaguing RGB LED with 2D dimming technology is color shift. This undesirable variation makes it difficult to use RGB LED as light sources in the backlight system. This paper describes the useful method of the optical feedback system for 2D dimming RGB LED backlight. The test results show that our proposed method is very suitable for the 2D dimming technology.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.5
• /
• pp.756-761
• /
• 2009

In this paper, a X band voltage controlled oscillator is proposed. The oscillator uses a transistor as an oscillating element and its oscillating frequencies are controlled by the tuning voltage of varactor diode. Using the circuit simulation tools, the matching circuits between the transistor and varactor diode, its input and output matching circuits, and a feedback circuits are designed. The measured results of the fabricated oscillator show that its oscillation frequencies are from 10.50GHz to 10.88GHz according to the turning voltages of 1V to 18V, its output power levels are about 4.3dBm, and its phase noise is around -43.5dBc/Hz at 100kHz offset frequency of 10.5GHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.496-496
• /
• 2007

Low level laser therapy has various therapy effects. This paper performed the basic study for fabricating the low level laser therapy apparatus, and one of the goals of this paper was to make this apparatus used handily. The apparatus has been fabricated using the laser diode and microprocessor unit. The apparatus used a 7850m Laser diode for blood stream improvement and was designed for a pulse width modulation type to increase stimulation effects. In result, we could get the light power of 785nm wavelength.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.497-499
• /
• 2005

A portable terminal assistant market grows rapidly every year and it requires many change in research on display devices. Among many newly developing methods, OLED(Organic Light Emitting Diode) is considered an advanced flat display device because its excellent characteristics, including high speed response, full color performance, low power consumption and flux of panel. However changes in the market of display shows that the market will require 3-dimensional images, but it is hard for existing 2-dimensional displays to make 3-dimensional images. Therefore we will try to find various methods such as holograms. In this paper, we will show existing flat displays can make 3-dimensional images by applying Lenticular Screen printing techniques on the organic semiconductor display device.