• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.109-112
• /
• 2003

SRM(switched reluctance motor) provides a excellent adjustable speed and torque characteristics. SRM has the possibility of maintaining full power over a wide speed range. So, many attempts are being done from home appliances to industrial applications. Especially, a traction drive of an SRM is one of a good application for it's DC-series characteristic. However, because of the switching mechanism and reluctance torque, it has some disadvantage Of noise and Vibration. It is difficult to adopt to an appliance demanding silency. A performance and noise tests with 6/4 and 12/8 SRM were done to compare the characteristics.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.871-878
• /
• 2018

In this paper, the conducted EMI reduction performances of active feed-forward current-sensing current-actuation (CSCA) and voltage-sensing current-actuation (VSCA) filters for a three-phase induction motor drive system are evaluated by experiments. For comparison purposes, the conducted EMI (CM emission, DM emission and total emission) of a three-phase induction motor drive with a conventional CM choke, a conventional CM choke in series with an active VSCA filter, and an active CSCA filter (where the CM choke was modified and used as a sensing current transformer) were compared to the case of a system without any filter inserted. Experimental results show that the active CSCA and VSCA filters can improve the CM reduction performance of the conventional CM choke by about 5 dB especially at low-frequencies. However, for DM comparisons, it shows that there is no different between cases with and without filters inserted.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.307-310
• /
• 2008

This paper is proposed the vector control of 3-phase induction motor drive system by photovoltaic generation. For performance of vector control using a current control voltage source inverter(CC-VSI). CC-VSI is controlled by torque and flux producing component of motor current, relating with current and voltage value of photovoltaic arrays at maximum power point that varies follow different level of insolation. The MPPT using a DC-DC converter controlled the duty cycle to track maximum power from PV under different insolation conditions. The simulation results are shown that the characteristics and performance of drive system, which varies as each conditions of light by expresses in voltage($V_{dq}$), current($I_{dq}$), speed of motor and torque.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.334-336
• /
• 2007

This paper proposes a novel RGB-LED (light emitting diode) backlight system, for 32" LCD TVs, accompanied by a new X-Y Channel drive method in which its row and column switches control the individual division screen. This proposed driving method is able to produce division drive effects such as image improvement and reduced power consumption. Not only that, the number of converter needed in this method, that is 1 with $4^*$(m+n) switches, is much fewer than that of cluster drive method, that is $4^*(m^*n)$.

• Journal of Drive and Control
• /
• v.4 no.4
• /
• pp.70-77
• /
• 2007

• Journal of Power Electronics
• /
• v.13 no.5
• /
• pp.806-813
• /
• 2013

This paper aims to compare the performance of three phase induction motor drives using Five Leg Inverter (FLI) and Three Leg Inverter (TLI) configurations. An Indirect Field Oriented Control (IFOC) method using a TLI is well established and incorporated for high performance speed drives in various industries. The FLI dual motor drive system on the other hand shows good workability in the independent control of two induction motor drives simultaneously. In this experiment, the IFOC method is utilized for both drive systems, and Space Vector Pulse Width Modulation (SVPWM) is used to generate pulses for both inverters. For the FLI, the Double Zero Sequence (DZS) Injection technique is used to generate the modulation signal. The complete experiment setup is done by using a DSpace 1103 controller board. The individual motor performances are analyzed using similar schemes, equipment setups and controller parameter values. The results show similar speed performance response capability between the single motor operation using a TLI system and the two motor operation using a FLI system based on the variable speed range either in forward or reverse operation. They also show similar load rejection abilities. However, the single motor with a TLI has a better power quality aspect such as ripple current and total harmonics distortion (THD).

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.3-6
• /
• 2001

This paper designs a drive for high efficiency of the 3-phase IM (induction motor) for FCU(Fan Coil Unit). The speed control system of 3-phase IM for FCU has been implemented by a TMS320LF2406 DSP chip. The DSP TMS320LF2406, which include the most peripheral circuit for control of the Industrial motor suitable for AC motor drive. This type of the controller can be obtained low cost and high reliance. The proposed drive system of the 3-phase IM for the FCU is verified by simulation. The results show the speed control characteristics of the control strategy Proposed for 3-Phase IM drive.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.1
• /
• pp.68-78
• /
• 2008

This paper introduces a complete package for SRM drive on Power System Computer-Aided Design/Electromagnetic Transients (PSCAD/EMTDC). A three-phase SRM drive is modeled and simulated on PSCAD. The motor is modeled using an accurate nonlinear analytical model that takes into consideration the machine nonlinearities. A current control algorithm is applied for torque ripple minimization to achieve a smooth output torque which is necessary for high performance applications. The motor drive is tested for four-quadrant operations. The modeled SRM is capable of operating as a motor or generator during clockwise and counterclockwise motions. The proposed package helps in understanding the operational principles of switched reluctance motors, investigating the dynamic characteristics of SRM drives, and achieving a high performance dynamic control task.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.755-761
• /
• 2003

Recently, the development of mobile devices demands information storage systems to use micro drive devices and cheap media. These should have several characteristics, for example, the subminiature of size, the robustness of shock, the minimum of cost and power consumption, and the removability of multiple applications. A conventional optical disk drive is more suitable for these specifications than the others. The optical storage system of the new generation to use a blue laser and a high numerical aperture (NA) is the perfect candidate for micro optical disk drives. In this paper, the micro actuator that can be applied to a micro optical disk drive is designed by response surface methodology to use a structural analysis and an electro-magnetic analysis. Based on above results, the coarse actuator and fine actuator are designed and improved from the point of view of the size and the power. Consequently, the designs of a micro actuator are proposed through these courses.

• Proceedings of the KIPE Conference
• /
• 2014.11a
• /
• pp.15-16
• /
• 2014

This paper proposed a construction of BMS to adopt energy storage system using flow battery. To operate flow battery system with BMS, there are motor drive system to pump electrolyte up. And it needs sensors to check leaking and temperature. The proposed system is verified by experiment.