• Korean Journal of Metals and Materials
• /
• v.49 no.8
• /
• pp.628-634
• /
• 2011

SA508 Gr.4N Ni-Cr-Mo low alloy steel, in which Ni and Cr contents are higher than in commercial SA508 Gr.3 Mn-Mo-Ni low alloy steels, may be a candidate reactor pressure vessel (RPV) material with higher strength and toughness from its tempered martensitic microstructure. The inner surface of the RPV is weld-cladded with stainless steels to prevent corrosion. The goal of this study is to evaluate the microstructural properties of the clad interface between Ni-Cr-Mo low alloy steel and stainless weldment, and the effects of post weld heat treatment (PWHT) on the properties. The properties of the clad interface were compared with those of commercial Mn-Mo-Ni low alloy steel. Multi-layer welding of model alloys with ER308L and ER309L stainless steel by the SAW method was performed, and then PWHT was conducted at $610^{\circ}C$ for 30 h. The microstructural changes of the clad interface were analyzed using OM, SEM and TEM, and micro-Vickers hardness tests were performed. Before PWHT, the heat affected zone (HAZ) showed higher hardness than base and weld metals due to formation of martensite after welding in both steels. In addition, the hardness of the HAZ in Ni-Cr-Mo low alloy steel was higher than that in Mn-Mo-Ni low alloy steel due to a comparatively high martensite fraction. The hardness of the HAZ decreased after PWHT in both steels, but the dark region was formed near the fusion line in which the hardness was locally high. In the case of Mn-Mo-Ni low alloy steel, formation of fine Cr-carbides in the weld region near the fusion line by diffusion of C from the base metal resulted in locally high hardness in the dark region. However, the precipitates of the region in the Ni-Cr-Mo low alloy steel were similar to that in the base metal, and the hardness in the region was not greatly different from that in the base metal.

• Journal of Aquaculture
• /
• v.19 no.4
• /
• pp.281-287
• /
• 2006

Intraspecific diploid androgenesis was achieved in mud loach (Misgurnus mizolepis) by the inhibition of the first mitotic division using combined thermal treatment. A combined thermal treatment (heat shock at $40.5\;^{\circ}C$ for 120 sec followed by cold treatment at $1\;^{\circ}C$ for 45 min) applied to the 1st metaphase of cell division (28 min post insemination at $25\;^{\circ}C$) successfully recovered viable androgenetic diploidy. Mean hatching success of the androgenetic diploid group was 29.6%, and the average yield out of total eggs taken was about 7% assessed at 1 week of age. However, relatively large variations in the yield of diploid androgenesis were observed among different egg batches used as cytoplasmic donors. Successful diploidization was confirmed by flow cytometric analysis, and parthenogenic reproduction in a paternal exclusive manner was verified with transgene dosage. Significant mortality was found in most androgenetic groups especially from hatch to 1 month of age, although such mortality was stabilized later.

• Korean Journal of Materials Research
• /
• v.13 no.3
• /
• pp.180-184
• /
• 2003

Ce-doped $Y_2$SiO$_{5}$ phosphor particles of spherical morphology, fine size, high crystallinity and high photoluminescence (PL) intensity were prepared by spray pyrolysis. When nitrate precursor solution is adopted, hollow particles were formed by uneven drying rate between surface and inside of droplet. Citric acid and ethylene glycol were introduced as polymeric precursor to control the morphology of particles. When polymeric solution is adopted, polymeric chain is formed by the esterification reaction between carboxyl and hydroxy groups of citric acid and ethylene glycol, and considered as controlling the drying characteristics of droplet. $Y_2$$SiO_{5}$ :Ce phosphor particles prepared from polymeric precursor solution were spherical, filled, fine size and not agglomerate before and after post heat treatment. The optimum doping concentration of cerium was 0.5 mol% of overall solution concentration. The optimum amount of TBOS of high PL intensity and pure crystallinity of X2-type $Y_2$$SiO _{5}$ was 105% of stoichiometric amount. The PL intensity of $Y_2$X$/_{5}$ :Ce phosphor particles prepared using the polymeric precursor solution was 164% of that of the nitrate precursor solution due to homogeneous composition and good morphology.y.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.896-903
• /
• 2002

The susceptibility of SCC for the weldment and PWHT specimens of HT-60 steel was evaluated using a slow strain rate method under applied potential by means of the potentiostat in synthetic seawater. In case of the parent, anodic polarization voltage was inappropriate in elongating the time to failure(TTF). -0.8V corresponding to cathodic protection range is most effective in improving the SCC resistance against corrosive environment. In case of the weldment, the values of reduction of area(ROA) and TTF at -0.68V corresponding to cathodic polarization value were 45.2% and 715,809sec which were the largest and longest life among other applied potentials. Those were vise versa at -1.1V. In case of the PWHT specimens, TTF and ROA at -0.68V was longest and largest like the weldment. Besides, PWHT is effective in prolonging the time to failure of the welded off-shore structure due to softening of effect. Regardless of the weldment and PWHT specimen, as corrosion rate gets higher, TTF becomes shorter and deformation behaviour for the weldment and PWHT specimen at -1.1V was shown to be irregular. Finally, it was found that specimens showed brittle fracture at -1.1V, but more ductile fracture accompanying the micro-cracks at applied potential of -0.68V.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.5
• /
• pp.183-188
• /
• 2020

Lead zinc niobate (PZN)-added lead zirconate titanate (PZT) thick films with thickness of 5~10 ㎛ were fabricated on silicon and sapphire substrates using aerosol deposition method. The contents of PZN were varied from 0 %, 20 % and to 40 %. The PZN-added PZT film showed poorer electrical properties than pure PZT film when the films were coated on silicon substrate and annealed at 700℃. On the other hand, the PZN-added PZT film showed higher remanent polarization and dielectric constant values than pure PZT film when the films were coated on sapphire and annealed at 900℃. The ferroelectric and dielectric characteristics of 20 % PZN-added PZT films annealed at 900℃ were compared with the result values obtained from bulk ceramic specimen with same composition sintered at 1200℃. As annealing temperature increased, dielectric constant increased. These came from enhanced crystallization and grain growth by post heat treatment.

• Journal of the Korean Ceramic Society
• /
• v.43 no.2 s.285
• /
• pp.85-91
• /
• 2006

Electron Beam Physical Vapor Deposition (EB-PVD) was applied to fabricate a thin film YSZ electrolyte with large area on the porous NiO-YSZ anode substrate. Microstructural and thermal stability of the as-deposited electrolyte film was investigated via SEM and XRD analysis. In order to obtain an optimized YSZ film with high stability, both temperature and surface roughness of substrate were varied. A structurally homogeneous YSZ film with large area of $12\times12\;cm^2$ and high thermal stability up to $900^{\circ}C$ was fabricated at the substrate temperature of $T_s/T_m$ higher than 0.4. The smoother surface was proved to give the better film quality. Precise control of heating and cooling rate of the anode substrate was necessary to obtain a very dense YSZ electrolyte with high thermal stability, which affords to survive after post heat treatment for fabrication a cathode layer on it as well as after long time operation of solid oxide fuel cell at high temperature.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.6
• /
• pp.774-780
• /
• 2009

The objectives of this study were to test the efficacy of induction of estrus and determine the timing of ovulation in relation to preovulatory LH and estrogen surges in cycling Murrah buffaloes subjected to Heatsynch protocol (GnRH-$PGF_2{\alpha}$-Estradiol benzoate). In experiment 1, the buffaloes (n = 10) were treated with Heatsynch protocol and observed for estrus and ovulation. In experiment 2 and 3, 30 cycling Murrah buffaloes were used to investigate the efficacy of Heatsynch protocol in terms of conception rates in summer (experiment 2) and winter (experiment 3) seasons. Fixed time A.I. was performed in all the buffaloes at 48 and 60 h post-estradiol benzoate (EB) injection. All buffaloes responded to the Heatsynch protocol with expression of estrus for which ovulations were induced in 8 buffaloes (80%). Mean time interval from the EB injection to ovulation was 50.0${\pm}$2.0 h (range 44.0 to 60.0 h). The interval from the end of LH surge to ovulation was 18.5${\pm}$2.47 h (range 8 to 26 h). The interval from end of estrogen surge to ovulation was 26.75 ${\pm}$2.07 h (range 22 to 36 h). Mean LH peak after EB injection occurred at 20.81${\pm}$1.61 h (range 14 to 28 h) and mean estrogen peak after EB injection occurred at 9.62${\pm}$1.03 h (range 7 to 16 h). Hence, the mean estrogen peak preceded the mean LH peak by 11 h. It was observed that the percentage of conceptions to total number of estruses for control buffaloes was 18 and 30 in summer and winter, respectively, whereas it increased to 26 and 40 in Heatsynch treated buffaloes in respective seasons. The results suggest the possibility of using Heatsynch treatment followed by fixed time A.I. in buffaloes for fertility improvement, especially since the incidence of silent heat in buffaloes is very high.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.35.1-35.1
• /
• 2011

New photovoltaic (PV) materials and manufacturing approaches are needed for meeting the demand for lower-cost solar cells. The prototypal thin-film photovoltaic absorbers (CdTe and $Cu(In,Ga)Se_2$) can achieve solar conversion efficiencies of up to 20% and are now commercially available, but the presence of toxic (Cd,Se) and expensive elemental components (In, Te) is a real issue as the demand for photovoltaics rapidly increases. To overcome these limitations, there has been substantial interest in developing viable alternative materials, such as $Cu_2ZnSnS_4$ (CZTS) is an emerging solar absorber that is structurally similar to CIGS, but contains only earth abundant, non-toxic elements and has a near optimal direct band gap energy of 1.4~1.6 ev and a large absorption coefficient of ${\sim}10^4\;cm^{-1}$. The CZTS absorber layers are grown and investigated by various fabrication methods, such as thermal evaporation, e-beam evaporation with a post sulfurization, sputtering, non-vacuum sol-gel, pulsed laser, spray-pyrolysis method and electrodeposition technique. In the present work, we report an alternative method for large area deposition of CZTS thin films that is potentially high throughput and inexpensive when used to produce monolithically integrated solar panel modules. Specifically, we have developed an aqueous chemical approach based on chemical bath deposition (CBD) with a subsequent sulfurization heat treatment. Samples produced by our method were analyzed by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, absorbance and photoluminescence. The results show that this inexpensive and relatively benign process produces thin films of CZTS exhibiting uniform composition, kesterite crystal structure, and good optical properties. A preliminary solar cell device was fabricated to demonstrate rectifying and photovoltaic behavior.

• Progress in Superconductivity
• /
• v.13 no.2
• /
• pp.127-132
• /
• 2011

Many research groups have been manufacturing coated conductor by various processes such as PLD, MOD, and MOCVD, but the methods with production cost suitable for wide and massive application of coated conductor did not develop yet. Spray pyrolysis method adopting ultrasonic atomization was tried as one of the possible option. GdBCO precursor films have been deposited on IBAD substrate by spray pyrolysis method at low temperature and converted to GdBCO by post heat treatment. Ultrasonic atomization was used to generate fine droplets from precursor solution of Gd, Ba, and Cu nitrate dissolved in water. Primary GdBCO films were deposited at $500^{\circ}C$ and oxygen partial pressure of 1 torr. After that, the films were converted at various temperatures and low oxygen partial pressures. C-Axis oriented films were obtained IBAD substrates at conversion temperature of around $870^{\circ}C$ and oxygen partial pressures of 500 mtorr ~ 1 torr in a vacuum. Thick c-axis epitaxial film with the thickness of 0.4 ~ 0.5 ${\mu}m$ was obtained on IBAD substrate. C-axis epitaxial GdBCO films were successfully prepared by ex-situ methods using nitrate precursors on IBAD metal substrate. Converted GdBCO films have very dense microstructures with good grain connectivity. EDS composition analysis of the film showed a number of Cu-rich phase in surface. The precursor solution having high copper concent with the composition of Gd : Ba : Cu = 1 : 2 : 4 showed the better grain connectivity and electrical conductivity.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.16 no.1
• /
• pp.74-83
• /
• 2020

A number of so-called 'Type IV' cracking was reported to occur at the welded joints of the P91 steel or P92 steel reheat steam piping systems in Korean supercritical thermal power plants. The reheat steam piping systems are subjected to severe thermal and pressure loading conditions of coolant higher than 570℃ and 4MPa, respectively. In this study, piping analyses and design evaluations were conducted for the piping system of a specific thermal plant in Korea and suggestions were made how structural integrity could be improved so that type IV cracks at the welded joints could be prevented. Integrity evaluations were conducted as per ASME B31.1 code with implicit consideration of creep effects which was used in original design of the piping system and as per nuclear-grade RCC-MRx code with explicit consideration of creep effects. Comparisons were made between the evaluation results from the two design rules. Another approach with modification or reduction of the redundant supports in the piping systems was investigated as a tool to mitigate thermal stresses which should essentially contribute to prevention of Type IV cracking without major modification of the existing piping systems. In addition, a post weld heat treatment method and repair weld method which could improve integrity of the welded joint of P91 steel were investigated.