• Radiation Oncology Journal
• /
• v.23 no.4
• /
• pp.243-252
• /
• 2005

Purpose: Indoor air quality (IAQ) in the radiation treatment center which is generally located underground is important to the health of hospital workers and patients treated over a long period of time. this study was conducted to measure and analyze the factors related to IAQ and subjective symptoms of sick building syndrome, and to establish the causes influencing IAQ and find a solution to the problems. Methods and Materials : Self administrated questionnaire was conducted to check the workers' symptoms and understanding of the work environment. Based on a preliminary investigation, the factors related to IAQ such as temperature, humidity, fine particulate. carbon dioxide, carbon monoxide, formaldehyde, total volatile organic compounds (TVOC), and radon gas were selected and measured for a certain period of time in specific sites where hospital workers stay long in a day. And we also evaluated the surrounding environment and the efficiency of the ventilating system simultaneously, and measured the same factors at the first floor (outdoor) to compare with outdoor all quality, All collected data were assessed by the recommended standard for IAQ of the domestic and international environmental organizations. Results: Hospital workers were discontented with foul odors, humidity and particulate. They complained symptoms related to musculo-skeletal system, neurologic system, and mucosal-irritatation. Most of the factors were not greater than the recommended standard, but the level of TVOC was third or fourth times as much as the measuring level of some offices in the United States. The frequency and the amount of the ventilating system were adequate, however, the problem arising in the position of outdoor-air inlets and indoor-air outlets involved a risk of the indraft of contaminated air. A careful attention was a requirement in handling and keeping chemical substances including a developing solution which has a risk of TVOC emissions, and repositioning the ventilating system was needed to solve the contaminated-air circulation immediately Conclusion We verified that some IAQ-related factors and inadequate ventilating system could cause subjective symptoms in hospital workers. The evaluation of IAQ was surely needed to improve the underground working environments for hospital workers and patients. On the basis of these data, from now on, we should actively engage in designs of the department of radiation oncology or improvement in environments of the existing facilities.

• Land and Housing Review
• /
• v.3 no.4
• /
• pp.369-378
• /
• 2012

In France, there are many forms of organizations based on the intercommunal solidarity for city development and management. The purpose of the collaboration among Communes is to achieve high quality and well-equipped service-delivery system through co-operation of public services needed grand finances : water supply and sewage system and waste disposal system etc. The cooperation among French Communes and its effects, even though these were owing to the existing French local administration system, continued throughout regional co-management and social co-development process. This study suggested some characteristics and implications of the collaborative-style French new-town development and management organizations focused on the EPA, SAN and CA. First, the role of developmental corporation like EPA and its collaborative structure of decision-making are meaningful, because in these ways many related Communes could share a goal of new town development. Second, the way of new town corporation (SAN) is important in the sense of enabling the Communes to collaborate with each others while maintaining autonomy, so those are not simply state-directed objects, which was very difficult in the former French local administration system. Finally, transforming to CA (Communautes d'agglomeration:city community), EPA as an intercommunal corporation is possible to extend its purpose to the domain of regional planning including new town and periphery areas and change its position to a subject which can practice Commune's sustainable development according to stages of city's development and maturity. The most important implication of this study on urban development in Korea is that administrative consultative council or association among local governments and related authorities need to be established and effectively operate because multi-stakeholders could share a goal of urban development and management through that.

• Journal of Biosystems Engineering
• /
• v.4 no.1
• /
• pp.1-23
• /
• 1979

The use of barley seeder attached to rotary tiller in the rural area has a significant meaning not only for the solution of labor peak season, but also for the increase of land utilization efficiency. The facts that presently being used barley seeders are all based on the mechanical principles of the reverse rotation, center drive and are all using forward rotating tine, which is used to be easily and heavily worn out when it rotates reversely, raise problem of recommending them to rural area in Korea. Therefore, the main objective of the study was to develop new type of rotary tine attachable to barley seeders. To attain the objective the following approaches were applied. (1) The kinematic analysis of reverse rotating barley seeders. (2) The studies on the soil bin and artificial soil. (3) The comparative experiment on the power requirement of prototype tine. The results obtained from the studies are summarized as follow: 1. The kinematic analysis of barley seeder attached to rotary tiller: The following results were obtained from the kinematic analysis for deriving general formulae of the motion and velocity characterizing the rotary tine of barley seeders presently being used by farmers. a) The position vector (P) of edge point (P) in the rotary tine of reverse rotating, center drive was obtained by the following formula. $$P=(vt+Rcos wt)i+Rsin wt j+ \{ Rcos \theta r sin \alpha cos (wt- \beta +\theta r) +Rsin \theta r sin \alpha sin (wt-\beta + \theta r) \} lk $$ b) The velocity of edge point $(P^')$ of reverse rotating, center drive rotary tine was obtained by the following formula. $$(P^')=(V-wR sin wt)i+(w\cdot Rcoswt)j + \{ -w\cdot Rcos \theta r\cdot sin \alpha \cdot sin (wt-\beta +\theta r) + w\cdot Rsin \theta r\cdot sin \alpha \cdot cos (wt- \beta + \theta r \} k $$ c) In order to reduce the power requirement of rotary tine, the angle between holder and edge point was desired to be reduced. d) In order to reduce the power requirement, the edge point of rotary tine should be moved from the angle at the begining of cutting to center line of machine, and the additional cutting width should be also reduced. 2. The studies on the soil bin and artificial soil: In order to measure the power requirement of various cutting tines under the same physical condition of soil, the indoor experiments Viere conducted by filling soil bin with artificially made soil similar to the common paddy soil and the results were as follows: a) When the rolling frequencies$(x)$ of the artificial soil were increased, the densIty$(Y)$ was also increased as follows: $$y=1.073200 +0.070780x - 0.002263x^2 (g/cm^3)$$ b) The absolute hardness $(Y)$ of soil had following relationship with the rolling frequencies$(x)$ and were increased as the rolling frequencies were increased. $$Y=37.74 - \frac {0.64 + 0.17x-0. 0054x^2} {(3.36-0.17x + 0.0054x^2)^3} (kg/cm^3)$$ c) The density of soil had significant effect on the cohesion and angle of internal friction of soil. For instance, the soil with density of 1.6 to 1.75 had equivalent density of sandy loam soil with 29.5% of natural soil moisture content. d) The coefficient of kinetiic friction of iron plate on artificial soil was 0.31 to 0.41 and was comparable with that of the natural soil. e) When the pulling speed of soil bin was the 2nd forward speed of power tiller, the rpm of driving shaft of rotary was similar to that of power tiller, soil bin apparatus is indicating the good indoor tester. 3. The comparative experiment on the power requirement of prototype tine of reverse rotating rotary: According to the preliminary test of rotary tine developed with various degrees of angle between holder and edge pcint due to the kinematic analysis, comparative test between prototype rotary tine with $30 ^\circ $ and $10 ^\circ$ of it and presently being used rotary tine was carried out 2nd the results were as follows: a) The total cutting torque was low when the angle between holder and edge point was reduced. b) $\theta r$ (angle between holder and edge point) of rotary tine seemed to be one: of the factors maximizing the increase of torque. c) As the angle between holder and edge point ($\theta r$) of rotary tine was $30 ^\circ $ rather than $45 ^\circ $, the angle of rotation during cutting soil was reduced and the total cutting torque was accordingly reduced about 10%, and the reduction efficiency of total cutting torque was low when the angle between holder and edge point ($\theta r$) of rotary tine was $10 ^\circ $, which indicates that the proper angle between holder and edge point of rotary tine should be larger than $10 ^\circ $ and smaller than $30 ^\circ $ . From above results, it could be concluded that the use of the prototype rotary tine which reduced the angle between holder and edge point to $30 ^\circ $, insted of $45 ^\circ $, is disirable not only decreasing the power requirements, but also increasing the durabie hour of it. Also forward researches are needed, WIlich determine the optimum tilted angle of rotary brocket, and rearrangement of the rotary tine on the rotary boss.

• Journal of Fashion Business
• /
• v.6 no.1
• /
• pp.137-154
• /
• 2002

It's not easy to renew old brand of over 50 years history to the tastes of new consumer of our time. Most of national brands that has a history of some 20 years in Korea have strove for continuation and growth of brand to no avails, which can be taken as a good example of current situation. For instance, C company, one of the National brand of US which has a history of 51 years, has made its position secure as a fashion group and based itself on a sound foundation by establishing new marketing strategy and completing successful brand renewal in the process of strategic M&A with Italian company. Those successful marketing strategies are as follows. 1) they regarded both market and consumer oriented marketing activity as company's highest priority strategy and put great emphasis upon concentration on target market and reestablishment of brand image of business casual wear. 2) Setting up and operating planning team composed of merchandizer alone in Milano, they set the direction of plan on the basis of concentrated research on potential item in market according to thorough market research done by buying office in Korea, branch office in Hong Kong and buyer in US prior to blueprint planning for season. 3) Great emphasis was placed on business which focused on intensive presentation of basic key item for apparel career women who are main consumer group in the midium-low prices market in US and on supplementation of size and color. they named this line 'collectibles' and helped their customer develop their own clothes plan without worrying about the change of color and fabric by supporting same fabric and color throughout the year and enabled them to add variation easily by supplementing new trend item. 4) Company set black as a main color that lots of apparel career women find easy to care and to express their own image and presented them with pebble which belongs to navy and beige and added fashion color such as wine and brown etc as season goes by. They constructed basic line in order for their customers to coordinate purchased item with new one or to add them to present collection, and to achieve efficient sale by setting up strategy which allows this cross coordination and changing pattern occasionally. 5) Though basic jacket for 99$, short slim skirt for 49$ are products within midium-low prices range, in the material planning stage aiming at production of item that has both resonable function appealing to consumer and is fashionable, synthetic material had to be used as a main source due to price competitiveness. Despite this situation, considering comfortable sense of fit and refined drape of silhouette that has no sign of cheap material, whole collectible line was divided into two items, which contributed to reduction of cost. In case of material that is composed of triacetate and polyester in 70 to 30 ratio, was used up to 4 million yard, which allowed drastic curtailment of cost accompanied by concentration. In case of 'collectibles' line, using Korean material mainly, C company chose to have their product sewed in Southeast Asian countries where transportation is well developed and both productivity and quality verified by operating global production system which aiming at cutdown of cost through outsourcing production from the country where labor cost is low and getting finished product. Polarization between present consumers telling us that consumers with the mind of middle classes in the past no longer exists between consumers who seek after only fine article of highest quality and wise consumers who are sensible enough to judge bubble on correlation between price and quality. To cope with this change in new consumer mind, apparel makes changing their policy so as to produce item that has reasonable quality and falls within affordable price range anywhere in the world. and they're striving to get out of difficult situation by operating global marketing strategy which stresses separation of planning, production and sale and sensibility of fashion shared worldwide. The marketing strategy of C company can be exemplified as a successful one.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.10
• /
• pp.41-53
• /
• 2016

Stability of the braced earth wall in the composite ground, which is composed of the jointed base rocks and the soil strata depends on the earth pressure acting on it. In most cases, the earth pressure is calculated by the empirical method, in which base rocks are considered as a soil strata with the shear strength parameters of base rocks. In this case the effect of the joint dips of the jointed base rocks is ignored. Therefore, the calculated earth pressure is smaller than the actual earth pressure. In this study, the magnitude and the distribution of the earth pressure acting on the braced wall in the composite ground depending on the joint dips of the base rocks and the ratio of soil strata and base rocks were experimentally studied. Two dimensional large-scale model tests were conducted in a large scale test facility (height 3.0 m, length 3.0 m and width 0.5 m) by installing 10 supports in a scale of 1/14.5. The test ground was presumed with the base rock ratio of the composite ground of 65%:35% and 50%:50% and with the joint dips for each base rock layer, $0^{\circ}$, $30^{\circ}$, $45^{\circ}$ and $60^{\circ}$, respectively. And then finite element analyses were performed in the same condition. As results, the earth pressure on the braced wall increased as the base rock layer's joint dips became larger. And earth pressure at the rock layer increased as the rock rate became larger. The largest earth pressure was measured when the base rock rate was 50% (R50) and the rock layer's joint dips was $60^{\circ}$. Based on these results, a formular for the calculation of the earth pressure in the composite ground could be suggested. Distribution of earth pressure was idealized in a quadrangular form, in which the magnitude and the position of peak earth pressure depended on the rock ratio and the joint dips.

• Journal of The Korean Association For Science Education
• /
• v.35 no.2
• /
• pp.247-258
• /
• 2015

Students are engaged in classroom learning, and classroom learning occurs not only through conversation but also through nonverbal behavior. In science classrooms especially, there are meaningful nonverbal behaviors such as practical activities like observation and measurement. But these behaviors have not been properly investigated by existing instruments that try to measure students' engagement. This study aims to develop a new instrument for analyzing students' behavioral engagement especially in science classrooms. The method of developing the instrument was structured along three steps. First, student behaviors have been classified into fourteen categories through literature review and a series of observation of elementary science classroom. Second, based on these, a framework for analyzing student behavioral engagement has been developed. With the framework, every student moment could be labeled as Participatory Speech or Participatory Silence or Non-Participatory Speech or Non-Participatory Silence. Third, an instrument to which the framework is applied has been developed by using Microsoft Excel. As a trial, two fourth-grade students in elementary science class were analyzed with this instrument. The results of the trial analysis shows that the longest period of a science lesson was occupied by Participatory Silence (63% and 72%). Among the participatory silence, 'listening' was the most common (51% and 42% of the trial lesson) and 'observing' which is a specific behavior to science was the fourth position (17% and 17% of the trial lesson). It is expected that the developed instrument could be used in improving our understanding of the patterns of student engagement in science classrooms.

• Tuberculosis and Respiratory Diseases
• /
• v.46 no.6
• /
• pp.846-855
• /
• 1999

Background : Secondary pulmonary hypertension is an important final endpoint in patients with chronic hypoxic lung disease, accompanied by deterioration of pulmonary hemodynamics. The clinical diagnosis of pulmonary hypertension and/or cor pulmonale could be difficult, and simple noninvasive evaluation of pulmonary artery pressures has been an relevant clinical challenge for many years. Doppler echocardiography might to be a more reliable method for evaluating pulmonary hemodynamics in such patients in terms of the accuracy, reproducibility and easiness for obtaining an appropriate echocardiographic window than M-mode echocardiography. The aim of this study was to assess echocardiographic parameters associated with pulmonary arterial hypertension, defined by increasing right ventricular systolic pressure(RVSP), calculated from trans-tricuspid gradient in patients with chronic hypoxic lungs. Method : We examined 19 patients with chronic hypoxic lung disease, suspected pulmonary hypertension under the clinical guidelines by two dimensional echocardiography via the left parasternal and subcostal approach in a supine position. Doppler echocardiography measured RVSP from tricuspid regurgitant velocity in continuous wave with 2.5MHz transducer and acceleration time(AT) on right ventricular outflow tract in pulsed wave for the estimation of pulmonary arterial pressure. Results : On echocardiography, moderate to severe degree of pulmonary arterial hypertension was defined as RVSP more than 40mmHg, presenting tricuspid regurgitation. Increased right ventricular endsystolic diameter and shortened AT were noted in the increased RVSP group. Increased RVSP was correlated negatively with the shortening of AT. Other clinical data, including pulmonary functional parameters, arterial blood gas analysis and M mode echocardiographic parameters were not changed significantly with the increased RVSP. Conclusion : These findings suggest that shortened AT on pulsed doppler can be useful when quantifying pulmonary arterial pressure with increased RVSP in patients with chronic lung disease with hypoxemia. Doppler echocardiography in pulmonary hypertension of chronic hypoxic lungs is an useful option, based on noninvasiveness under routine clinical practice.

• KDI Journal of Economic Policy
• /
• v.32 no.2
• /
• pp.55-92
• /
• 2010

In terms of labor market accomplishments, such as income, size of the company, and the matching quality between one's job and college major (specialization), a very large discrepancy is observed between the graduates from colleges located in Seoul and those outside Seoul. But, when the department average score of the Scholastic Aptitude Test (SAT) at the time of college entrance is controlled for, the discrepancy is found to be reduced to a considerable degree. In the case of wage gap, at least two third can be explained by the SAT score gap. The remaining wage gap seems to reflect the characteristics of workplace. In other words, graduates with high SAT scores enter colleges located in Seoul and thus tend to find better jobs leading to earning differences. This result that confirms the importance of aptitude test scores suggests that in the labor market, one of the major reasons behind a lower accomplishment of the graduate from local colleges is due to a lower competitiveness of local colleges in attracting the brightest students. But, this should not be viewed as only an internal problem of local colleges. This is because the growth of local economies tends to haul the advancement of local colleges in that area rather than being the other way around. The agglomeration effect in Seoul where headquarters of large corporations and financial institutions gather is the factor that has elevated the status of colleges located in Seoul since this provides highly preferred job choices of graduates. When the competitiveness of college is significantly influenced by exogenous factors, such as the vicinity to Seoul, the effort being made by colleges alone would not be enough to improve the situation. However, the central government, too, is not in the position to carry out countermeasure policies for such problems. The regional development strategy boosted through supportive policies for local colleges, such as financial support, is not based on the persuasive and empirical grounds. It is true that college education is universal and that the government''s intervention in assisting local colleges to secure basic conditions, such as tenure faculty and adequate facilities is necessary. However, the way of intervention should not be a support-only type. In order to improve the efficiency and effect of financial support, restructuring programs, including the merger and integration of insolvent colleges, should be underway prior to providing support. In addition, when the policy is focused on education recipients-local college students, and not on education providers-local colleges, the importance of regional gap in compulsory education (elementary and junior high schools) turns out to be much important as the gap between metropolitan area colleges and local colleges. Considering the educational gap before college entrance shown from the discrepancies of aptitude test scores among different regions, the imbalance between regions in terms of human resources is apparently derived from compulsory education, and not from college education. Therefore, there is a need to double the policy efforts to reduce the educational gap among different regions. In addition, given the current situation where it is difficult to find appropriate ex post facto policy measures to solve the problem of income gap between the graduates from metropolitan colleges and local colleges, it can be said that improving the environment for compulsory education in local areas is a growing necessity for bridging the educational gap among different regions.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.3
• /
• pp.231-239
• /
• 2006

In this study, we evaluated the efficiency of using sulfur-$CaCO_3$ complex pellet in the sulfur oxidizing autotrophic denitrification process for synthetic wastewater with high $CaCO_3$ concentration. The sulfur-$CaCO_3$ complex pellet was packed in reactor(R4). Influent ${NO_3}^--N$ loading rate was from 200 to $1,000g/m^3{\cdot}day$. During the operation, average denitrification efficiency of R4 was above 95%. Particularly, the denitrififation rate at $1,000g/m^3{\cdot}day$ loading was 98.96% for R4. High ${NO_3}^--N$ removal efficiency was determined in R4 compared with other reactors. Through $Ca^{2+}$ and alkalinity analyses, we calculated the supplied alkalinity from the packed $CaCO_3$ in the reactor. Sulfur-$CaCO_3$ complex pellet more effectively supplied alkalinity through the dissociation of $CaCO_3$ as compared with other media. Based on these results, sulfur-$CaCO_3$ complex pellet increased the pH buffering capacity while also providing the carbon source to the denitrifying bacteria. Denitrification efficiency of R4 was also higher than other reactors. ESEM pictures of sulfur-$CaCO_3$ complex pellet show higher porosity than that of the granular sulfur. Hence, more denitrifying bacteria attached on the sulfur-$CaCO_3$ complex pellet than on granular sulfur. It can be concluded that the sulfur-$CaCO_3$ complex pellet is a more suitable media for a sulfur oxidizing autotrophic denitrification process as it provides high denitrification efficiency.

• Journal of Distribution Science
• /
• v.10 no.5
• /
• pp.7-17
• /
• 2012

The recent announcement of the National Research Foundation of Korea (NRF) to cease journal accreditation operations as of the end of the year 2014 can easily influence the future of many research journals in Korea. Although this plan has not yet been formalized or structured, its facilitation would be the major turning point for the current Korean research and scholarly journals and publications. In addition, the NRF's plan to select and fund top 20 or more research journals over the five year period beginning 2015 suggests that the competition will most likely increase among Korean journals. Each journal would need to develop its unique strategy to improve and strengthen its competitiveness to become or maintain its position as a major research journal in Korea. The association of Korean Distribution of Science (KODISA) and its research journal, Journal of Distribution Science (JDS), has been continuously improving its reputation as a reputable journal in the distribution and related fields since its establishment in 1999. Due to demand, JDS has had to undergo several changes in its publication cycle first from semiannual publication to quarterly, then finally to monthly publications in 2012, and has become one of the major social science journals in Korea. Furthermore, with the redesigning of its webpage with English language in July of 2011, KODISA has made the published journals freely accessible and available to both domestic and foreign researchers, scholars, practitioners, and learners. These changes have resulted in the rapid increase in the bounce rate and the number of journal submissions by foreign scholars, with four research articles having been submitted by foreign scholars just in March of 2012 alone. However, although the changes and outcomes have resulted in a reasonable success so far, the achievement may only become a short-term success without continuously developing, improving, and implementing both effective and efficient strategies through critical, thorough, and frequent examinations and evaluations of both KODISA and JDS. As such, the purpose of this research is to carefully examine both KODISA and JDS to identify problematic factors and to develop appropriate strategies to change or modify those problems for further strengthening and improving their reputation and status. The paper examines and analyzes the past, present, and future of KODISA and JDS and their managerial, operational, and systematic procedures and operations. The narrow scope of research and inefficiencies in promoting the association and the journal and the improvement of impact factors are identified as the notable problems that could hinder JDS from being included in SCOPUS or SSCI in the near future. This type of examination and exploration has not been previously conducted, so the major limitation of this paper can be identified as not meticulously elaborating on the problems nor proving detailed recommendations based on the existing researches. This article asserted that solving the problem of the narrow scope of research would lead to facilitation of resolving other inefficient problems. Inclusion of international academic disciplines to the distribution and their related fields would be the viable initiation of expanding the research area, and this strategy could promote the journal as well as improve its impact factors. The narrow scope of research seems to be a good research topic and merit further exploration as an individual research project, because this kind of research could yield the creation of new understandings or theories.