• 센서학회지
• /
• 제17권1호
• /
• pp.9-14
• /
• 2008

In this paper, the gas responses of tungsten oxide films prepared by anodic reaction was discussed. Sensing electrodes and heating electrodes were patterned by photolithography method on quartz substrate. Porous tungsten oxide was fabricated in electrolyte solutions of 5 % HF (HF :$C_2H_6OH:H_2O$=3 : 2 : 20) by anodic reaction. The anodic reaction with metal (platinum wire) as a cathode and the sensing device as an anode was conducted under the various reaction times (1-10 min) at 10 mA/$cm^2$ The surface structure and morphology of the fabricated sensor have been analysed by X-ray diffraction (XRD) and field-emission scanning electron microscopy (FE-SEM). All the peaks of XRD results were well indexed to the pure phase pattern. The average diameter of the porous tungsten oxide surface were ranged about 100 nm. The fabricaed sensor showed good sensitivity to 200 ppm toluene at operating temperature of $250^{\circ}C$.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.81.2-81.2
• /
• 2011

The gas diffusion layer (GDL) consists of two main parts, the GDL backing layer, called as a substrate and the micro porous layer (MPL) coated on the GDBL. In this process, carbon particles of MPL penetrates to the GDBL consequently forms MPL penetration part. In this study, the micro porous layer (MPL) penetration thickness is determined as a design parameter of the GDL which affect pore size distribution profile through the GDL inducing different mass transfer characteristics. The pore size distribution and water permeability characteristics of the GDL are investigated and the cell performance is evaluated under fully/low humidification conditions. Transient response and voltage instability are also studied. In addition, to determine the effects of MPL penetration on the degradation, the carbon corrosion stress test is conducted. The GDL that have deep MPL penetration thickness shows better performance in high current density region because of enhanced water management, however, loss of penetrated MPL parts is shown after aging and it induces worse water management characteristics.

• Journal of Electrochemical Science and Technology
• /
• 제7권3호
• /
• pp.218-227
• /
• 2016

The light harvesting efficiency is counted as an important factor in the power conversion efficiency of DSSCs. There are two measures to improve this parameter, including enhancing the dye-loading capacity and increasing the light trapping in the photoanode structure. In this paper, these tasks are addressed by introducing a macro-porous silicon (PSi) substrate as photoanode. The effects of the novel photoanode structure on the DSSC performance have been investigated by using energy dispersive X-ray spectroscopy, photocurrent-voltage, UV-visible spectroscopy, reflectance spectroscopy, and electrochemical impedance spectroscopy measurements. The results indicated that bigger porosity percentage of the PSi structure improved the both anti-reflective/light-trapping and dye-loading capacity properties. PSi based DSSCs own higher power conversion efficiency due to its remarkable higher photocurrent, open circuit voltage, and fill factor. Percent porosity of 64%, PSi(III), resulted in nearly 50 percent increment in power conversion efficiency compared with conventional DSSC. This paper showed that PSi can be a good candidate for the improvement of light harvesting efficiency in DSSCs. Furthermore, this study can be considered a valuable reference for more investigations in the design of multifunctional devices which will profit from integrated on-chip solar power.

• 한국수산과학회지
• /
• 제40권4호
• /
• pp.220-225
• /
• 2007

The succession of marine benthic algae and the restoration of an artificial seaweed forest on a porous type (shaped half saw teeth) artificial reef at Jeju island, Korea was studied. Young thalli of Sargassum horneri and Ecklonia cava were attached to different artificial substrates. In general, the succession on the artificial reefs led from filamentous algae to perennial algae and involved more than 25 species that are useful fishery resources, including E. cava. Coralline algae were dominant on the artificial reefs at the Kangjung site. The maximum algal biomass on the artificial reef in October 2005 was $1,990g/m^2$ at Biyang. In conclusion, a climax community and seaweed forest can be attained one year after the substrate is constructed.

• 한국전기전자재료학회논문지
• /
• 제16권4호
• /
• pp.330-335
• /
• 2003

This paper reports the optimum structure of the vacuum packaged Porous poly-silicon Nano-Structured (PNS) emitter. The PNS layer was obtained by electrochemical etching process into polycrystalline silicon layer in a process controlled to anodizing condition. Current-voltage studies were carried out to optimize process condition of electron emission properties as a function of anodizing condition and top electrode thickness. Also, we measured in advance the electron emission properties as a function of substrate temperature because the vacuum packaged process was performed under the condition of high temperature ambient (430$^{\circ}C$). Auger Electron Spectrometer (AES) studies shows that Au as a top-electrode was diffused to PNS layer during temperature experiments. Thus, we optimized the thickness of top-electrode in order to make the vacuum package PNS emitter. As a result, the vacuum Packaged PNS emitter was successfully emitted by optimizing process.

• 한국표면공학회지
• /
• 제52권2호
• /
• pp.96-102
• /
• 2019

Magnesium and its alloys are prone to be corroded, thus surface treatments improving corrosion resistance are always required for practical applications. As a surface treatment of magnesium alloys, plasma electrolytic oxidation (PEO), creating porous stable oxide layer by a high voltage discharge in electrolyte, enhances the corrosion resistance. However, due to superhydrophilicity of the porous oxide layer, which easily allow the penetration of corrosive media toward magnesium alloys substrate, post-treatments inhibiting the transfer of corrosive media in porous oxide layer are required. In this work, we employed a hydrophobizing method to enhance the corrosion resistance of PEO treated Mg alloy. Three types of hydrophobizing techniques were used for PEO layer. Thin Teflon coating with solvent evaporation, self-assembled monolayer (SAM) coating of octadecyltrichlorosilane (OTS) based on solution method and SAM coating of perfluorodecyltrichlorosilane (FDTS) based on vacuum method significantly enhances corrosion resistance of PEO treated Mg alloy with reducing the contact of water on the surface. In particular, the vacuum based FDTS coating on PEO layer shows the most effective hydrophobicity with the highest corrosion resistance.

• 한국표면공학회지
• /
• 제53권6호
• /
• pp.312-321
• /
• 2020

Morphology of porous cobalt electro-deposits was systematically investigated as functions of cobalt precursors in the plating bath and applied cathodic current density with a special focus on cobalt nano-rod formation. It was proved that the concentration of cobalt precursor plays little effect on the morphology of cobalt electro-deposits at relatively low plating current density while it significantly affects the morphology with increasing plating current density. Such a dependence was discussed in terms of the kinetics of two competitive reactions of cobalt reduction and hydrogen evolution. Cobalt nano-rod structure was created at specific ranges of cobalt precursor content and applied cathodic current density, and its diameter and length varied with plating time without notable formation of side branches which is usually found during dendrite formation. Specifically, the nano-rod length was preferentially increased in relative short plating time (<15 s), resulting in higher aspect ratio of nano-rod with plating time. Whereas, both the nano-rod length and diameter were increased nearly at the same level in a prolonged plating time, making the aspect ratio unchanged. From the analysis of crystal structure, it was confirmed that the cobalt nano-rod preferentially grew in the form of single crystal on a dense poly-crystalline cobalt thin film initially formed on the substrate.

• Steel and Composite Structures
• /
• 제47권5호
• /
• pp.633-644
• /
• 2023

Taking a look at the previously published papers, it is revealed that there is a porosity index limitation (around 0.35) for the mechanical behavior analysis of the functionally graded porous (FGP) structures. Over mentioned magnitude of the porosity index, the elastic modulus falls below zero for some parts of the structure thickness. Therefore, the current paper is presented to analyze the vibrational behavior of the FGP Timoshenko beams (FGPTBs) using a novel refined formulation regardless of the porosity index magnitude. The silica aerogel foundation and various hydrothermal loadings are assumed as the source of external forces. To obtain the FGPTB's properties, the power law is hired, and employing Hamilton's principle in conjunction with Navier's solution method, the governing equations are extracted and solved. In the end, the impact of the various variables as different beam materials, elastic foundation parameters, and porosity index is captured and displayed. It is revealed that changing hygrothermal loading from non-linear toward uniform configuration results in non-dimensional frequency and stiffness pushing up. Also, Al - Al2O3 as the material composition of the beam and the porosity presence with the O pattern, provide more rigidity in comparison with using other materials and other types of porosity dispersion. The presented computational model in this paper hopes to help add more accuracy to the structures' analysis in high-tech industries.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1573-1575
• /
• 2004

An alumina membrane with nano-sized pores was fabricated by anodic oxidation. The shape and structure of the pore on alumina membrane were changed according to the roughness of aluminum surface. The shape and structure of the nano-sized pre were investigated according to purity of aluminum substrate for the anodization process. The aluminum substrates with 99.5% and 99.999% purities were used. The aluminum substrate(99.5%) was anodized after the processes of pressing, mechanical polishing, chemical polishing, and electrochemical polishing. The nano-sized pores with the pore size of 50 - 100nm, the cell size of 20-50nm and the thickness of $10{\mu}m{\sim}45{\mu}m$ were obtained. Even though the electrochemical polishing was used for the aluminum substrate (99.999%), the same characteristics as the aluminum substrate (99.5%) was obtained. The alumina membrane prepared by anodization for 5 min using fixed voltage method shows the pore with irregular shape. The pore shape was changed to regular shape after pore widening process.

• 한국인쇄학회지
• /
• 제18권1호
• /
• pp.1-11
• /
• 2000

The influence of the first coating layer on the properties of the second coating layer is reported. For various model coating composition, ratios of first and second coating weights are used to generate coating layers. The void volume, pore size distribution and light scatter coefficient of the coatings are measured. In some cases, the fine material from the second layer seems to penetrate the first layer to reduce the void fraction of the total system. Rapid setting coating, for example thin layers on porous first layer tends to generate porous coating layers.