• Polymer(Korea)
• /
• v.37 no.2
• /
• pp.240-248
• /
• 2013

The curing behaviors of diglycidyl ether of bisphenol A (DGEBA) with mercaptan hardener were studied by the comparison with amine-adduct type hardener. Curing behaviors were evaluated by DSC at dynamic and isothermal conditions. In the DSC, the dynamic experiments were based on the method of Kissinger's equation, and the isothermal experiments were fitted to the Kamal's kinetic model. Activation energy of epoxy/amine-adduct type hardener was ca. 40 kcal/mol. As the functional group of mercaptan hardener, -SH increased, on epoxy/mercaptan hardeners, the activation energies decreased from 28 to 19 kcal/mol. Epoxy/amine-adduct type hardener was initiated at $90^{\circ}C$ or higher. However, epoxy/mercaptan hardeners reduced the initiation temperatures below $80^{\circ}C$ and shortened the durations of curing reaction within 10 min. We found out that the reaction kinetics of epoxy with mercaptan hardener followed the autocatalytic reaction models, and the maximum reaction rates were shown at the conversions of 20~40%.

• Elastomers and Composites
• /
• v.45 no.3
• /
• pp.217-222
• /
• 2010

Paved roads are suffered from the permanent plastic deformation in hot summer and cracks in cold winter, which are detrimental to safe driving. This leads to necessity of modification of asphalt to resist those deformation. In this study, two kinds of modifiers were examined; organic polymers and a photoinitiator which is activated by ultraviolet lay. The mechanical and rheololgical properties of modified asphalts were examined using UTM and rheometer. Results showed that the properties were varied depending on the types of polymer and irradiation time. UV irradiation increased the tensile strength and storage modulus of thermoplastic polymer-modified asphalt, however UV was not effective on thermoset polymer. According to long term ultraviolet curing test, properties of the polymer/photoinitiator-modified asphalt did not decrease, but rather increase for 20 years. This indicates that the useful life of the asphalt could be extended by addition of photoinitiator.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.52 no.6
• /
• pp.101-110
• /
• 2010

This study was performed to evaluate the void ratio and strength of porous polymer concrete used coarse aggregates and unsaturated polyester resin to find optimum mix design of porous polymer concrete for planting block. Also, this study was performed to evaluate the planting properties of herbaceous plant and cool-season grass in porous polymer blocks based on the experimental results of porous polymer concrete to develop environmentally friendly planting blocks. Tests for the void ratio and compressive strength of porous polymer concrete were performed at the curing age 7 days. Also, kinds of plants such as Tall fescue, Perennial ryegrass, Lespedeza and Alfalfa for planting were applied to porous polymer blocks. Within 6 weeks after seed, initial germination ratio, cover view and growth length for planting blocks were estimated by various methods.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.135-140
• /
• 2001

This study was developed high-quality a large size precast channel structure using polymer concrete to improve quality of the product as well as to enhance construction quality. Precast PC represent the fastest growing segment of the polymer concrete industry. The fast curing, high strength, and low impermeability permit thin section and rapid reuse of moulds. Developed precast channel structure will be structural experiment and analysis. Also, through an example to construct will be develop the most suitable section survey and make practicable.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.814-816
• /
• 2005

In this paper, we describe how specially developed polymer capped, nano-particle silver inks can be used to print circuitry for applications like displays, RFID antennas and "disposable electronics". The requirements of printing on temperature sensitive flexible substrates (such as polymer films and papers) that require low temperature curing is also discussed.

• Polymer(Korea)
• /
• v.39 no.1
• /
• pp.185-190
• /
• 2015

Since a transition from liquid crystal to crystal state is slow for the large photo-reactive liquid crystal molecules, it needs a long time for recrystallization of LC242 molecules when lowering the temperature of the liquid crystal. Although liquid crystals usually align along one direction, the directions of individual liquid crystal molecules are little different from one another with increasing temperature, resulting in changes of birefringence of the liquid crystal films. When the photo-reactive liquid crystals are photo-cured, faster curing kinetics and much larger curing degrees are observed for the films cured at the liquid crystal phase.

• Polymer(Korea)
• /
• v.24 no.2
• /
• pp.201-210
• /
• 2000

To determine the effect of chain length of linear amine curing agents on the thermal and mechanical properties, standard epoxy resin, diglycidyl ether of bisphenol A (DGEBA) was cured with diethylenetriamine (DETA), triethylenetetraamine (TETA) and tetraethylenepentaamine (TEPA) in a stoichiometrically equivalent ratio. From this work, the effect of linear amine curing agents on the thermal and mechanical properties was significantly influenced by chain length of curing agents. In contrast, the results showed that the DGEBA/DETA system had higher values than the DGEBA/TETA and DGEBA/TEPA system in the density, shrinkage (%), thermal expansion coefficient, tensile modulus, and flexural strength. Whereas the DGEBA/DETA cure system had lower values than the DGEBA/TETA and DGEBA/TEPA cure system in the maximum exothermic temperature, conversion (%), and T$_{g}$. These findings imply that the differences in the maximum conversion about the chain length of curing agents affect the thermal and mechanical properties.s.

• Polymer(Korea)
• /
• v.31 no.6
• /
• pp.491-496
• /
• 2007

In the polymeric dental restorative composites, the resin matrix mainly contains 70 wt% 2,2-bis[4-(2-hydroxy-3-methacryloyloxy propoxy) phenyl] propane (Bis-GMA), as a base resin and 30 wt% triethylene glycol dimethacrylate (TEGDMA) as a diluent. Even though the viscosity of the resin matrix is rapidly decreased by adding TEGDMA, addition of TEGDMA to the Bis-GMA results in reduction in the mechanical properties and increase in the curing shrinkage of the dental composite. In order to fabricate dental composite exhibiting excellent properties by reducing TEGDMA content in the resin matrix, in this study, Bis-GMA derivatives, which do not contain hydroxyl groups, were used instead of Bis-GMA. The curing characteristics of Bis-GMA derivatives were similar with those of Bis-GMA, while the former exhibited lower viscosity and water absorption than the latter. Comparing the curing shrinkage of the dental composite containing Bis-GMA derivative with that prepared from Bis-GMA, the reduction in curing shrinkage was about 25%. Dental composites prepared from new resin matrices also exhibited low water uptake and better properties in mechanical strength.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.333-338
• /
• 2000

At present, reinforced concrete pipe has been widely used as drain pipe. However, many reinforced concrete pipe is exposed at deteriorated environment by the growth of a sulfur-oxidizing bacterium isolated from corroded concrete. The purpose of this study is to evaluate the effects of lining by polymer-modified mortar on the development in durability of reinforced concrete pipe. Polymer-modified mortars ate prepared with various polymer typer as cement modifier and polymer-cement ratio and rested for compressive and flexural strengths, adhesion in tension, acid resistance test, freezing and thawing test, and lining test of product in the field. From the rest results, it is apparent that polymer-modified mortars have good mechanical properties and durability as lining material. In practice, all polymers can be used as lining materials for reinforced concrete pip, and type of polymer, and polymer-cement ratio and curing conditions are controlled for good lining product.

• Polymer(Korea)
• /
• v.24 no.2
• /
• pp.220-227
• /
• 2000

Silica and carbon black filled natural rubber (NR) vulcanizates were prepared with different mixing modes and amounts of fillers. Curing characteristics, morphology. and tear properties of the NR vulcanizates were investigated. The NR vulcanizates filled with silica and carbon black sequentially showed longer induction time ($t_2$), cure index ($t_{90}$ ), and lower maximum torque ($T_{max}$ ) than the NR vulcanizates filled with them simultaneously, during curing process. The former showed superior dispersion of fillers and tear properties to the latter. The NR vulcanizates containing 30 phr of silica showed excellent properties in the experimental range.