• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 추계학술대회 논문집(II)
• /
• pp.1035-1040
• /
• 2002

Railway plate girder bridges have characteristics that are not show dominant frequency in dynamic response frequencies like obtained vertical acceleration on the bridge during the train passing because the train loading relatively bigger than the bridge self-weight. This paper experimentally confirmed in FFT result has various frequencies due to inherent characteristic of railway train loading. To establish classification of dynamic frequency range in railway bridge acceleration during the train passing, vibration frequencies result from experimental test are analyzed concerning actuation vibration factors. Factors are train velocity, train type, mass ratio of vehicle/bridge, stiffness of bridge, bridge/track and vehicle/track. From the result, it is proposed that the frequencty classfication table with corresponding factors. Using the proposed table to develop rehabilitation technique of the plate girder bridge, to expect vibration reduction and comfort enhancement of the railway plate girder bridge.

• Steel and Composite Structures
• /
• 제10권4호
• /
• pp.297-315
• /
• 2010

This paper is concerned with free vibration characteristics and natural frequency of horizontally curved composite plate girder bridges. Three-dimensional finite element models are developed for the girders using the software package LUSAS and analyses carried out on the models. The validity of the finite element models is first established through comparison with the corresponding results published by other researchers. Studies are then carried out to investigate the effects of total number of girders, number of cross-frames and curvature on the free vibration response of horizontally curved composite plate girder bridges. The results confirm the fact that bending modes are always coupled with torsional modes for horizontally curved bridge girder systems. The results show that the first bending mode is influenced by composite action between the concrete deck and steel beam at low subtended angle but, on the girders with larger subtended angle at the centre of curvature such influence is non-existence. The increase in the number of girders results in higher natural frequency but at a decreasing rate. The in-plane modes viz. longitudinal and arching modes are significantly influenced by composite action and number of girders. If no composite action is taken into account the number of girders has no significant effect for the in-plane modes.

• 대한토목학회논문집
• /
• 제30권5A호
• /
• pp.407-415
• /
• 2010

현재 국내에서 설계되고 있는 40~70 m 지간의 강도로교 90% 이상이 박스거더교 형식이며 박스거더교는 휨 강성과 비틀림 강성이 뛰어나 장경간이나 곡선을 갖는 교량 형식으로 적합할 뿐만 아니라 가설현장에서의 작업을 최소화 할 수 있어 현장 안전관리 면에서도 유리한 구조형식이다. 그러나 박스거더는 상하 플랜지와 복부판이 수직, 수평보강재로 보강되는 구조로 부재량과 용접량이 많이 소요되어 비경제적인 교량 형식으로 많이 지적되어 왔다. 따라서, 미국이나 일본에서는 상대적으로 부부재를 줄일 수 있는 보다 경제적인 플레이트거더교가 일반적으로 적용되고 있다. 이러한 플레이트거더교의 한 형식인 소수주거더교는 강합성교량의 합리화를 위해 많이 채용되는 형식으로, 주거더 간격을 종래의 3 m 정도에서 2배 정도인 6 m 이상으로 증가하여 주거더의 개수를 최소화시키는 경제적인 교량형식이다. 또한, 거더 단면의 단순화를 위하여 거더의 복부판에 부착되는 수평보강재와 수직보강재를 최대한 생략할 수 있다. 2주거더교는 소수주거더교의 대표적인 형식으로, 유효폭 10 m 전후의 교량에 적합하여 프랑스를 중심으로 유럽에서는 1960년대부터 본격적으로 개발되어왔다. 국내에서는 소수주거더교 적용시 안전율 확보를 위해 유럽이나 일본 등에 비해 많은 강재량을 사용하고 있으며, 설계자들의 친밀도 부족과 박스거더교에 비해 복잡한 설계 등과 같은 여러가지 실무적용 차원에서 적용이 제한되고 있는 실정이다. 이 연구에서는 합리화 강교량 형식인 소수주거더교의 제작방법을 개선하고 구속콘크리트를 활용하여 강교량에서 공사비와 직결되는 강중을 줄일 수 있는 신형식 강합성거더(Turn Over Composite Girder) 구조형식을 제안하고자 한다. 또한 실물 크기인 20 m 단면회전방법을 적용한 강합성 거더시험체 및 교량시험체를 제작하여 제작성을 평가하고 구조성능 실험을 하여 구조안전성을 평가하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.568-573
• /
• 2005

To the installed CWR (Continuously Welded Rail) on steel plate girder bridges without ballast, shoes were replaced by the shoe for reduced axial force. During 9 months, from summer to winter, expansion by a temperature on girders, axial forces by a temperature on CWR, etc. are tested and the results are evaluated. Also, with the numerical analysis, the results - axial forces by a temperature on CWR, deformations of girders, etc. are compared and evaluated. From the longitudinal displacement on girders, occurred by run of trains, because of looking for the stability, the bearings for reducing axial forces are applied to the railway bridges. It is verified that the bearings for reducing axial forces disperse the axial forces by a temperature from the measurement of the forces on CWR of plate girder bridges,.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 춘계학술대회 논문집
• /
• pp.511-518
• /
• 2000

The high speed train service will be offered for high-quality transport service in existing railway by Korean National Railroad(KNR). Therefore, this paper presents the results of analysis carried out to determine the dynamic response characteristics of deck plate girder bridges which are representative elevated structures of existing railway and to evaluate their suitabilities for supporting Korea Train Express(KTX) trainsets in the speed range 0-250 km/h. Their dynamic characteristics are analyzed concerning structural safety, train-operation safety and passenger comfort. The simplified method for 2-dimensional train/track/bridge interaction analysis is utilized in the analysis of dynamic behaviors of deck plate girder bridges.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.558-564
• /
• 2006

When vehicles pass the connection between the bridge and earthwork, the difference of both sections' stiffness produces an increasing wheelload. As a consequence, it results in the excessive vibration of vehicles and the damage of bearing system. In general, steel plate girder railway bridges without ballast track have larger stiffness than the bridge with ballast, and produces larger impulse on the bridge superstructure. Thus, it is necessary to reduce the differences of both stiffness. This study presents parametric studies on the behavior of plate girder bridges and their tracks by means of various stiffnesses and the length of approach zone. The results of numerical study showed that the smaller the stiffness of both sides and the longer the length of approach zone, the variation of wheelload becomes smaller. Hence, it gives less burden into the plate girder bridges and their tracks. It is expected that the results of parametric study can be used as a preliminary data for the determination of economical length on the approach zone and the stiffness of both sides.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 춘계학술대회 논문집
• /
• pp.356-363
• /
• 2003

The CWR of the plate girder bridges in non-ballast causes the additional axial force on the rail and the bearing due to the temperature axial force and the interaction between the CWR and bridges. This study shows the remarkable improvement of reducing the axial force of the CWR on the non-ballast bridge, compared to conventional methods. New method, which is differently designed in terms of longitudinal semi-rigid bearing, reduces the axial force on the bearing by making the girder act both directions. This method is applicable to most cases of bridges regardless of the restriction of length, and useful to reduce the abrasion and damage of the track material.

• Steel and Composite Structures
• /
• 제49권2호
• /
• pp.215-230
• /
• 2023

Cable-girder anchorage joint is the critical part of cable-supported bridges. Tensile-plate anchorage (TPA) is one of the most commonly used types of cable-girder anchorage joints in steel girder cable-supported bridges. In recent years, it has been proposed by bridge designers to apply TPA to concrete girder cable-supported bridges to form composite cable-girder anchorage joint (CCGAJ). In this paper, the mechanical performance of CCGAJ under tensile force is studied through experimental and numerical analyses. Firstly, the effects of the external prestressing (EP) and the bearing plate (BP) on the mechanical performance of CCGAJ were investigated through three tests. Then, finite element model was established for parametrical study, and was verified by the experimental results. Then, the effects of shear connector forms, EP, BP, vertical rebar rate, and perforated rebar rate on the tensile capacity of CCGAJ were investigated through numerical analyses. The results show that the tensile capacity of CCGAJ depends on the first row of PR. The failure mode of CCGAJ using headed stud connectors is to form a shear failure surface at the end of the studs while the failure mode using PBLs is similar to the bending of a deep girder. Finally, based on the strut-and-tie model (STM), a calculation method for CCGAJ tensile capacity was proposed, which has a high accuracy and can be used to calculate the tensile capacity of CCGAJ.

• 대한토목학회논문집
• /
• 제26권4A호
• /
• pp.611-620
• /
• 2006

강합성 플레이트 2-거더교는 피로균열에 의해 한 개의 거더에 심각한 손상이 발생되는 경우 교량의 붕괴가 유발되는 단재 하경로 구조로 인식되고 있다. 본 논문에서는 강합성 2-거더교의 거더 손상시 교량의 여유도를 평가하기 위한 해석적 연구를 수행하였다. 여유도 평가는 단경간 및 3경간 연속교를 대상으로 하였으며, 수직브레이싱은 I-단면 가로보로 적용하고 하부 수평브레이싱이 설치되는 경우와 설치되지 않는 경우를 고려하였다. 정상 상태 및 손상 상태의 교량에 대해 하부 수평브레이싱의 유 무에 따른 내하 성능을 재료 및 기하비선형 해석으로 구하고 각 경우의 여유도를 비교 평가하였다. 해석 결과에 따르면 정상 상태의 2-거더 교량은 단순교와 연속교 모두 수평브레이싱이 없어도 여유도가 충분하며, 손상 상태의 교량에서는 수평브레이싱이 여유도 향상에 중요한 역할을 하는 것으로 분석되었다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1569-1576
• /
• 2011

To install heavy structures in the railway bridges, crane methods or launching methods using temporary structure have been applied. These methods are uneconomical because working yard is required, temporary cut of rail system, etc. In this study, various construction methods has been developed which are suitable to the filed conditions. In the case of simple span structure like plate girder bridges, the girder is loaded to troy system at the working yard and then transferred to the working place. To lift and lower the girder system, a new transfer system was developed. Different methods each for simple span bridge girder and long span girder were developed and detailed work procedures were proposed. Using these methods, the heavy structures can be installed with simple and safe work procedures and the construction cost and duration can be reduced.