• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.3
• /
• pp.38-45
• /
• 2009

Recently, LCD Backlight Unit is being replaced from cold cathode fluorescent lamp(CCFL) to external electrode fluorescent lamp(EEFL) because the EEFL has high energy efficiency and long life. Also, it can reduce energy consumption and weight. So far, external electrode ring for EEFL is produced by sheet metal press forming process. Therefore it had low precision and much material loss. To solve these problems, Multi-Forming process that has five step forming process was invented. However, low productivity is another barrier. Product speed that is controlled by the rotational speed cannot be increased due to the unsatisfied design specification. The reason is that the gap between rolled two edge parts of the sheet plate is tightly inspected. Regarding this factor, the understanding of forming behavior to each process is inevitable. This paper describes the CAE analysis of the multi-forming process by PAM-STAMP.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.274-277
• /
• 2006

This paper describes a lighting warning system (LWS) which consists of a corona needle electrode, a low noise differential amplifier, an A/D converter, an one-chip microprocessor, a LCD and alarm devices. The corona needle electrode is used to measure electric field intensity caused by thunderclouds on the ground level. To evaluate the sensitivity of the LWS, calibration experiment was carried out using a round-shape parallel plate electrode system. The theoretical and experimental results show that the LWS can measure electric field intensity over 2 [kV/m].

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.648-651
• /
• 1993

A parallel plate type electrolytic ozone generator for ozone asher has been fabricated and studied, and 4 kinds of ozone generation anode electrode having different slits have also been investigated. It is found that there were optimum conditions for the slits of electrode, which, however, controls the field in the interelectrode spacing, and allows sideflow waterpaths through the slits in the electrode. As a result, the generated ozone concentrations of A, B, C and D type electrode showed 2.2, 1.3, 1.5 and 3.0 ppm for 400 ml/min flowrate tap water test, and, ozone yields of 11, 13, 15 and 30 $mg/kWhcm^2$ respectively.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.180-186
• /
• 2001

Underwater wet welding process was experimentally investigated by using the six types of flux coated electrodes of 3.2mm diameter and the KR-RA steel plate of 11mm thickness as base metal. Two types of electrodes were domestic covered are welding electrode(CR13, CR14) and another two types of wet welding electrodes(UW-CS-01, TN-20) and the other two types(UW-X1, UW-X2) where individually designed flux coasted electrode for experimental welding purpose.

• Journal of the Korean Chemical Society
• /
• v.20 no.4
• /
• pp.280-289
• /
• 1976

The silver selenide electrode has been prepared and its properties as an indicating electrode for silver ion have been investigated. Epoxy resin was used as a filler of silver selenide electrode. Silver metal plate was directly connected with the membrane of the electrode and the silver paste was used as its binder. The sintered electrode was more sensitive and stable than the pressed electrode, and the silver selenide electrode more sensitive than the silver sulfide electrode to silver ion. The linear relationship between the electrode potential and logarithmic concentration of silver ion has been observed down to 10-6 M for the electrode. Several heavy metal ions except mercuric ion did not interfere this linearity, but halide, cyanide, and thiocyanate ions did intensively interfere owing to the formation of silver compounds and complexes. This electrode has been applied to the potentiometric titration for determining halide ion. It is concluded that interferences from ,$CN^-, SCN^-, S^-, I^-, Br^-, Cl^- and Hg^{2+}$ ions are detrimental to the practical use of the electrodes for measuring pAg.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.05a
• /
• pp.1285-1286
• /
• 2005

• Journal of Welding and Joining
• /
• v.27 no.3
• /
• pp.85-91
• /
• 2009

A roll projection welding machine is introduced to fabricate metallic sandwich plate consisting of a structured inner sheet with projection-like shape and a pair of skin sheets. To fabricate the metallic sandwich plate of consistent and good quality, two process monitoring methods are introduced; dynamic resistance monitoring and skin sheet temperature monitoring. Dynamic resistance monitoring has no time delay but gives only averaged value over plate width. Skin sheet temperature monitoring has certain amount of time delay but is good for predicting weld quality of specified position. By the two complementary monitoring methods, the characteristics of the new welding process is successfully understood.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.456-461
• /
• 2003

A fuel cell is an electrochemical device in which the energy of a chemical reaction is converted directly into electricity. By combining hydrogen fuel with oxygen from air, electricity is formed, without combustion of any form. Water and heat are the only by-products when hydrogen is used as the fuel source. Fuel cell stack consists of multi-layered unit cells. A unit cell consists of MEA and bipolar plates. The end plate of fuel cell stack should give a uniform distributed pressure to multi unit cell layers so as to reduce the contact resistance and to prevent the leakage of reactant gases and the damage of multi layer components. The current end plate is redundantly large and heavy. It makes the power per unit volume reduced. Topology optimization of end plate is conducted for mass reduction and enhancement of bending rigidity. The evaluation of the current design and the recommendation for the future design is remarked.

• Journal of Surface Science and Engineering
• /
• v.43 no.1
• /
• pp.25-30
• /
• 2010

Titanium and titanium alloys are widely used for orthopedic and dental implants for their superior mechanical properties, low modulus, excellent corrosion resistance and good biocompatibility. In this study, corrosion behaviors of nanotube formed on the bone plate of Ti-6Al-4V alloy for dental use have been investigated. $TiO_2$ nanotubes were formed on the dental bone plates by anodization in $H_3PO_4$ containing 0.6 wt % NaF solution at $25^{\circ}C$. Electrochemical experiments were performed using a conventional three-electrode configuration with a platinum counter electrode and a saturated calomel reference electrode. Anodization was carried out using a scanning potentiostat (EG&G Co, Model 263A USA), and all experiments were conducted at room temperature. The surface morphology was observed using field emission scanning electron microscopy (FE-SEM) and energy dispersive x-ray spectroscopy(EDS). The corrosion behavior of the dental bone plates was examined using potentiodynamic test(potential range of -1500~2000 mV) in a 0.9% NaCl solution by potentiostat (EG&G Co, PARSTAT 2273. USA). The inner diameter of nanotube was about 150~180 nm with wall thickness of about 20 nm. The interspace of nanotube to nanotube was 50 nm. The passive region of the nanotube formed bone plates showed the broad range compared to non-nanotube formed bone plates. The corrosion surface of sample was covered with corrosion products.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.9
• /
• pp.85-91
• /
• 2022

The demand for electric vehicles has increased because of environmental regulations. The lithium-ion battery, the most widely used type of battery in electric vehicles, is composed of a cathode, an anode, and an electrolyte. It is manufactured according to the pole plate, assembly, and formation processes. To improve battery performance and increase manufacturing efficiency, the manufacturing process must be optimized. To do so, simulation can be used to reduce wasted resources and time, and a finite-element method can be utilized. For high simulation quality, it is essential to reflect the material properties of the electrode by considering the pores. However, the material properties of electrodes are difficult to derive through measurement. In this study, the representative volume element method, which is a homogenization method, was applied to estimate the representative material properties of the electrode considering the pores. The representative volume element method assumes that the strain energy before and after the conversion into a representative volume is conserved. The method can be converted into one representative property, even when nonhomogeneous materials are mixed in a unit volume. In this study, the material properties of the electrode considering the pores were derived. The results should be helpful in optimizing the electrode manufacturing process and related element technologies.