• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.28-34
• /
• 2019

Solar energy is one of the most abundant renewable energy sources on Earth but there are restrictions on the use of solar thermal energy due to the time-discrepancy between the solar-rich season and heating demand. In Europe and Canada, a seasonal solar thermal energy storage (SSTES), which stores the abundant solar heat in the summer and uses the heat for the winter heating load, is used. Recently, SSTES has been introduced in Korea and empirical studies are actively underway. In this study, a $2,000m^2$ flat plate type solar collector and $20,000m^2$ of borehole thermal energy storage (BTES) were studied for a greenhouse in Hwaseong City, which has a heating load of 2,164 GJ/year. To predict the dynamic performance of the system over time, it was simulated using the TRNSYS 18 program, and the solar fraction of the system with the control conditions was investigated. As a result, the solar BTES system proposed in this study showed an average solar fraction of approximately 60% for 5 years when differential temperature control was applied to both collecting solar thermal energy and discharging BTES. The proposed system simplified the configuration and control method of the solar BTES system and secured its performance.

• Journal of the Korean Society for Heat Treatment
• /
• v.32 no.5
• /
• pp.201-211
• /
• 2019

Low carbon steel (S20C steel) and SPCC steel sheet have been austenitic nitrided at $700^{\circ}C$ in a closed pit type furnace by changing the flow rate of ammonia gas and heat treating time. When the flow rate of ammonia gas was low, the concentration of residual ammonia appeared low and the hardness value of transformed surface layer was high. The depth of the surface layer, however, was shallow. With increasing the concentration of residual ammonia by raising up the ammonia gas flow, both the depth of the surface layer and the pore depth increased, while the maximum hardness of the surface layer decreased. By introducing a large amount of ammonia gas in a short time, a deep surface layer with minimal pores on the outermost surface was obtained. In this experiment, while maintaining 10~12% of residual ammonia, the flow rate of inlet ammonia gas, 7 liter/min, was introduced at $700^{\circ}C$ for 1 hour. In this condition, the thickness of the surface layer without pores appeared about $60{\mu}m$ in S20C steel and $30{\mu}m$ in SPCC steel plate. Injecting additional methane gas (carburizing gas) to this condition played a deteriorating effect due to promoting the formation of vertical pores in the surface layer. For $1^{st}$ transformed surface layer for S20C steel, maintaining 10~12% residual ammonia condition via austenitic nitriding process resulted in ${\varepsilon}$ phase with relatively high nitrogen concentration (just below 4.23 wt.%N) among the mixed phases of ${\varepsilon}+{\gamma}$. The ${\varepsilon}$ phase was formed a specific orientation perpendicular to the surface. For $2^{nd}$ transformed layer for S20C steel, ${\gamma}$ phase was rather dominant (just above 2.63 wt.%N). For SPCC steel sheet, there appeared three phases, ${\gamma}$, ${\alpha}(M)$ and weak ${\varepsilon}$ phase. The nitrogen concentration would be approximately 2.6 wt.% in these phases condition.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.12
• /
• pp.924-930
• /
• 2018

The objective of this study was to investigate heating performance characteristics of electric heat pump system in a fuel cell electric vehicle (FCEV). In order to analyze heating performance characteristics of electric heat pump system with plate-type heat exchanger using stack coolant to evaporate the refrigerant, R-134a, each component was installed and tested under various operating conditions, such as air inlet temperature of inner condenser and compressor speed. When the air inlet temperature of inner condenser was varied from $0.0^{\circ}C$ to $-20.0^{\circ}C$, heating capacity was not quite different due to similar temperature gap between inlet and outlet of inner condenser with electric-driven expansion valve (EEV). However, COP increased until certain EEV opening, especially under 45.0%, because of decreasing power consumption. According to the compressor speed variation from 2,000 to 4,000 RPM, heating capacity and COP were found to have opposite trend. In the future works, stack coolant conditions as the heat source for tested heat pump system were analyzed with respect to heating performance, such as heating capacity and COP.

• Animal Bioscience
• /
• v.34 no.8
• /
• pp.1392-1402
• /
• 2021

Objective: The growth rate of pigs is related to differentiation and proliferation of muscle cells, which are regulated by growth factors and expression of growth-related genes. Thus, the objective of this study was to establish optimal culture conditions for Jeju black pig (JBP) muscle cells and determine the relationship of various factors involved in muscle growth with the proliferation of JBP muscle cells. Methods: Muscles were taken from the femur skeletal muscle of JBP embryos. After isolation of the muscle cells, cells were cultured in a 6-well plate under four different culture conditions to optimize culture conditions for JBP muscle cells. To analyze proliferation rate of JBP muscle cells, these muscle cells were seeded into 6-well plates at a density of 1.5×10⁵ cells per well and cultured for 3 days. Western blot and quantitative real-time polymerase chain reaction were applied to verify the myogenic differentiation 1 (MyoD) expression and growth-related gene expression in JBP muscle cells, respectively. Results: We established a muscle cell line from JBP embryos and optimized its culture conditions. These muscle cells were positive for MyoD, but not for paired box 7. The proliferation rate of these muscle cells was significantly higher in a culture medium containing bFGF and epidermal growth factor + basic fibroblast growth factor (EGF+bFGF) than that without a growth factor or containing EGF alone. Treatment with EGF and bFGF significantly induced the expression of MyoD protein, an important transcription factor in muscle cells. Moreover, we checked the changes of expression of growth-related genes in JBP muscle cells by presence or absence of growth factors. Expression level of collagen type XXI alpha 1 gene was changed only when EGF and bFGF were added together to culture media for JBP muscle cells. Conclusion: Concurrent use of EGF and bFGF increased the expression of MyoD protein, thus regulating the proliferation of JBP muscle cells and the expression of growth-related genes.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.1
• /
• pp.59-69
• /
• 2021

Recently, large-scale offshore and coastal structures have been constructed owing to the increasing interest in eco-friendly energy development. To achieve this, precise simulations of waves are necessary to ensure the safe operations of marine structures. Several experiments are required in the field to understand the offshore wave; however, in terms of scale, it is difficult to control variables, and the cost is significant. In this study, numerical waves under various wave conditions are produced using a piston-type wavemaker, and the produced wave profiles are verified by comparing with the results from a numerical wave tank (NWT) modeled using the smoothed particle hydrodynamics (SPH) method and theoretical equations. To minimize the effect by the reflected wave, a mass-weighted damping zone is set at the right end of the NWT, and therefore, stable and uniform waves are simulated. The waves are generated using the linear and Stokes wave theories, and it is observed that the numerical wave profiles calculated by the Stokes wave theory yield high accuracy. When the relative depth is smaller than two, the results show good agreement irrespective of the wave steepness. However, when the relative depth and wave steepness are larger than 2 and 0.04, respectively, the errors are negligible if the measurement position is close to the excitation plate. However, the error is 10% or larger if the measurement position is away from the excitation location. Applicable target wave ranges are confirmed through various case studies.

• Applied Chemistry for Engineering
• /
• v.33 no.6
• /
• pp.630-635
• /
• 2022

Copper(II) oxide (CuO), electroless plated on a nitrogen-containing carbon sponge prepared by a melamine sponge thermal treatment, was developed as a nitric oxide (NO) gas sensor that operates without a wafer. The CuO content on the surface of the carbon sponge increased as the plating time increased, but the content of nitrogen known to induce NO gas adsorption decreased. The untreated carbon sponge showed a maximum resistance change (5.0%) at 18 min. On the other hand, the CuO plated sample (CuO30s-CS) showed a maximum resistance change of 18.3% in 8 min. It is considered that the improvement of the NO gas sensing capability was caused by the increase in hole carriers of the carbon sponge and improved movement of electrons due to CuO. However, the NO gas detection resistance of the CuO electroless plated carbon sponge for 60 s decreased to 1.9%. It is considered that the surface of the carbon sponge was completely plated with CuO, resulting in a decrease in the NO gas adsorption capacity and resistance change. Thus, CuO-plated carbon sponge can be used as an effective NO gas sensor because it has fast and excellent resistance change properties, but CuO should not be completely plated on the surface of the carbon sponge.

• Journal of Adhesion and Interface
• /
• v.23 no.2
• /
• pp.53-58
• /
• 2022

Here, the surface characteristics of the dielectric were controlled by introducing the self-assembled monolayers (SAMs) as the intermediate layers on the surface of the AlOx dielectric, and the electrical performances of the organic charge modulated transistor (OCMFET) were significantly improved. The organic intermediate layer was applied to control the surface energy of the AlOx gate dielectric acting as a capacitor plate between the control gate (CG) and the floating gate (FG). By applying the intermediate layers on the gate dielectric surface, and the field-effect mobility (μ_OCMFET) of the OCMFET devices could be efficiently controlled. We used the four kinds of SAM materials, octadecylphosphonic acid (ODPA), butylphosphonic acid (BPA), (3-bromopropyl)phosphonic acid (BPPA), and (3-aminopropyl)phosphonic acid (APPA), and each μ_OCMFET was measured at 0.73, 0.41, 0.34, and 0.15 cm2V-1s-1, respectively. The results could be suggested that the characteristics of each organic SAM intermediate layer, such as the length of the alkyl chain and the type of functionalized end-group, can control the electrical performances of OCMFET devices and be supported to find the optimized fabrication conditions, as an efficient sensing platform device.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.8
• /
• pp.25-34
• /
• 2008

A new hybrid oedometer cell is designed and manufactured to investigate a behavior of soft soils by using elastic and electromagnetic waves during consolidation test. Bender elements, which generate and detect shear waves, are placed in the top cap and the bottom plate and mounted on the oedometer wall. Double wedge type electrical resistance probe, which measures local void ratio change, is positioned onto the top cap of the oedometer cell. The bender elements and the electrical resistance probe are anchored into a nylon set screw with epoxy resin. The nylon set screw with epoxy resin minimizes directly transmited elastic waves through the oedometer cell due to impedence mismatch and allows for easy replacement of defected bender elements and electrical resistance probe. Primary consolidation time can be estimated from the slope of electrical resistance versus log time curve and the evolution of shear wave velocity. The shear wave velocity can be used to assess inherent anisotropy when disturbance effects are minimized because particle alignment affects the shear wave velocity. The void ratios evaluated by the electrical resistance probe are similar to those by the settlement during consolidation. This study suggests that the shear wave velocity and the electrical resistance can provide complementary imformations to understand consolidation characteristics such as primary consolidation, anisotropy, and void ratio.

• Korean Journal of Soil Science and Fertilizer
• /
• v.35 no.2
• /
• pp.118-126
• /
• 2002

To evaluate the correlations of microbial populations with soil healthiness and crop production and establish the criteria for microbial population of soil types. We analyzed the microbial community structure of 13 soils which were different in physical and chemical properties and cultivation methods. According to the analysis of microbial population suing the dilution plate method, the large differences of the microbial population structures among soil types were shown: aerobic bacteria $2-27{\times}10^6$, fluorescent Pseudomonas $1-1,364{\times}10^5$, Gram negative bacteria $1-126{\times}10^4$, and mesophilic Bacillus $1-110{\times}10^5$. The density of Gram negative bacteria was highest on red pepper cultivating soils (sample no. 4 and 6) of Umsung and Gesan, Chungbuk, and the density of the fluorescent Pseudomonas was highest on greenhouse soil (sample no. 7) of Jinju, Kyungnam. The crop productivity of three soils was high as compared with those of other soils. It was supposed that the density of fluorescent Pseudomonas and mesophilic Bacillus were correlated with the incresed crop production. By MIDI analysis, 579 strains isolated from 13 soils composed of a variety of microbes including 102 isolates of Agrobacterium, 112 isolates of Bacillus, 32 isolates of Pseudomonas, 44 isolates of Kocuria, and 34 isolates of Pseudomonas. Among the 624 isolates of Gram negative bacteria, Pseudomonas including P. putida and p. fluorescens occupied the highest density (51%), and Stenotrophomonas maltophilia and Burkholderia cepacia also appeared at high density. From RAPD analysis, the fluorescent Pseudomonas strains isolated from 13 soil types showed a high level of strain diversities and were grouped into 2 - 14 patterns according to soil types. Many of unknown bacteria were recovered from the paddy soil, and needed to be further characterized on the molecular basis.

• Korean Journal of Cleft Lip And Palate
• /
• v.3 no.1
• /
• pp.23-31
• /
• 2000

Objective: When an alveolar cleft is too large to close with adjacent mucobuccal flaps or large secondary fistula following a primary bilateral palatoplasty exists, a one-stage procedure for bone grafting becomes challenging. In such a case, we used the tongue flap to repair the fistula and cleft alveolus in the first stage, and bone grafting to the cleft defect was performed in the second stage several months later. The purpose of this paper is to report our experiences with the use of an anteriorly-based Y-shaped tongue flap to fit the palatal and labial alveolar defects and the ultimate result of the bone graft. Patients: A series of 14 patients underwent surgery of this type from January 1994 to December 1998.The average age of the patients was 15.8 years old (range: 5 to 28 years old). The mean period of follow-up following the 2nd stage bone raft operation was 45.9 months (range: 9 to 68 months). In nine of the 14 cases, the long-fork type of a Yshaped tongue flap was used for extended coverage of the labial side alveolar defects with the palatal fistula in the remaining cases the short-forked design was used. Results: All cases demonstrated a good clinical result after the initial repair of cleft alveolus and palatal fistula. There was no fistula recurrence, although Partial necrosis of distal margin in long-forked tongue flap was occurred in one case. Furthermore, the bone graft, which was performed an average of 8 months after the tongue flap repair, was always successful. Occasionally, the transferred tongue tissue was bulging and interfering with the hygienic care of nearby teeth; however, these problems were able to be solved with proper contour-pasty performed afterwards. No donor site complications such as sensory disturbance, change in taste, limitations in tongue movement, normal speech impairments or tongue disfigurement were encountered. Conclusion: This two-stage reconstruction of a bilateral cleft alveolus using a Y-shaped tongue flap and iliac bone graft was very successful. It may be indicated for a bilateral cleft alveolus patient where the direct closure of the cleft defect with adjacent tissue or the buccal flap is not easy due to scarred fibrotic mucosa and/or accompanied residual palatal fistula.