• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.169-169
• /
• 2011

STT-MRAM (수직자화 자기메모리)는 자화반전 현상을 원리로 구동하는 비휘발성 메모리로 기존의 메모리 장치에 비해 빠른 접근 속도와 높은 저장 밀도를 가지며 영구적인 기록이 가능하다. 이러한 장점들에 더해 적은 소모 전력을 지니므로 기존의 SRAM등의 한계를 극복할 대안으로 각광받고 있으며 차세대 메모리 군의 선두주자로 가장 적합한 후보중 하나이다. STT-MRAM의 건식 식각 방식에 있어 가장 큰 이슈는 소자 구동에 핵심적인 역할을 하는 MTJ(Magnetic Tunnel Junction)의 식각이다. MTJ는 free layer, tunnel barrier, pinned layer 3개의 층으로 구성되어 있으며 양 끝 layer에는 강자성체인 CoFeB가 사용되고 tunnel barrier에는 절연층인 MgO가 사용되고 있다. 이러한 물질들은 기존의 반도체 소자에서는 사용되지 않았던 물질들로 기존 공정에서 사용되던 Cl2 based plasma etching에서는 측벽에 비화발성 반응물과 잔류 Cl2에 의해 부식이 발생하는 문제점이 드러나고 있다. 이러한 문제점을 해결하기 위한 새로운 대안으로 CO/NH3/Ar나 CH4/Ar 같은 새로운 가스 조합을 사용하는 연구가 진행되고 있다. 이러한 연구에 의해 기존의 Cl2 plasma를 이용한 식각에서 나타나는 문제점은 해결이 되었으나 또 다른 문제점들이 보고되고 있다. 본 연구에서는 stack MRAM sample을 사용하여 기존의 사용되는 Cl2/Ar plasma와 대안 gas인 CO/NH3, CH4/Ar plasma에서의 식각을 진행하였으며 실험 조건(gas 비율 변화, Bias power 변화, 식각 시간)에 따른 식각 속도의 변화나 식각 후의 profile에 대하여 관찰하였다. 이에 따라 식각후에 어떠한 차이점이 있는 지를 알아보았으며 CO/NH3나 CH4/Ar plasma에서 식각시 나타나는 문제점에 대하여도 조명해 보았다.

• 마이크로전자및패키징학회지
• /
• 제9권4호
• /
• pp.55-60
• /
• 2002

본 연구는 $580^{\circ}C$의 저온에서 ICPHFCVD(inductively coupled plasma hot filament chemical vapor deposition)를 이용하여 탄소나노튜브를 수직성장 시키는 것을 나타낸 것이다. 또한, 탄소나노튜브의 끝단에 존재하는 Ni-tip을 비성질 탄소같은 탄소질 물질등의 서로 다른 에칭특성에 기초하여 RF plasma를 이용하여 일회 공정으로 불순물을 정제하고, 고찰하였다. 정제된 이후의 탄소나노튜브는 속이 비어있는 다중벽 탄소나노튜브로 나타났으며, 성장된 탄소나노튜브는 외경과 내경은 50 nm와 25 nm였다. 또한, 탄소나노튜브의 graphite 층의 총수는 약 82개 층으로 구성되었으며, 층과 층간의 거리는 0.34nm였다. 그리고 TEM 관찰 결과, 탄소나노튜브 tip의 Ni촉매는 계속적인 에칭 공정에 의해 효과적으로 제거 되었다.

• 한국전기전자재료학회논문지
• /
• 제24권12호
• /
• pp.935-938
• /
• 2011

The etching characteristics of ZnO and etch selectivities of ZnO to $SiO_2$ in $SF_6$/Ar plasma were investigated using Inductively-coupled-plasma (ICP). The maximum etch rates of ZnO were 6.5 nm/min at $SF_6$(50%)/Ar(50%), Source power (700 W), Bias power (250 W), Working pressure(8 mTorr). The etch rate of ZnO showed a non-monotonic behavior with increasing from 0% to 50% Ar fraction in $SF_6$/ Ar plasma. The plasma diagnostic were characterized using Optical Emission Spectroscopy (OES) analysis measurements.

• 한국전기전자재료학회논문지
• /
• 제23권10호
• /
• pp.752-758
• /
• 2010

The etching characteristics of indium tin oxide (ITO) thin films in an $O_2/BCl_3/Ar$ plasma were investigated. The etch rate of ITO thin films increased with increasing $O_2$ content from 0 to 2 sccm in $BCl_3$/Ar plasma, whereas that of ITO decreased with increasing $O_2$ content from 2 sccm to 6 sccm in $BCl_3$/Ar plasma. The maximum etch rate of 65.9 nm/m in for the ITO thin films was obtained at 2 sccm $O_2$ addition. The etch conditions were the RF power of 500 W, the bias power of 200 W, the process pressure of 15 mTorr, and the substrate temperature of $40^{\circ}C$. The analysis of x-ray photo electron spectroscopy (XPS) was carried out to investigate the chemical reactions between the surfaces of ITO thin films and etch species.

• 한국전기전자재료학회논문지
• /
• 제21권8호
• /
• pp.727-732
• /
• 2008

In this work, the etch characteristics of $VO_2$ thin films were investigated using inductively coupled plasma (ICP) of $Cl_2/Ar$ gas mixtures. To analyze the plasma characteristics, a quadrupole mass spectrometer (QMS), an optical emission spectroscopy (OES), and a Langmuir probe measuring system were used. The surface reaction of the $VO_2$ thin films was investigated using X-ray photoelectron spectroscopy (XPS). It was found that an increase in Ar fraction in the $Cl_2/Ar$ plasma at fixed gas pressure, input power, and bias power resulted in increasing $VO_2$ etch rate which reached a maximum value of 87.6 nm/min at 70-75 % Ar. It was confirmed that the etch rate of the $VO_2$ films was mainly controlled by the ion flux. On the basis of measuring results, we will discuss possible etching mechanism of $VO_2$ film in the $Cl_2/Ar$ plasma.

• Transactions on Electrical and Electronic Materials
• /
• 제9권1호
• /
• pp.1-5
• /
• 2008

ZnS is an attractive material for future optical and electrical devices since it has a direct and wide band gap to provide blue emission at room temperature. In this study, inductively coupled $BCl_3/Ar$ plasma was used to etch ZnS:Mn thin films. The maximum etch rate of 164.2 nm/min for ZnS:Mn was obtained at a $BCl_3(20)/Ar(80)$ gas mixing ratio, an rf power of 700 W, a dc bias voltage of -200V, a total gas flow of 20 sccm, and a chamber pressure of 1Pa. The etch behaviors of ZnS:Mn thin films under various plasma parameters showed that the ZnS:Mn were effectively removed by the chemically assisted physical etching mechanism. The surface reaction of the ZnS:Mn thin films was investigated by X-ray photoelectron spectroscopy. The XPS analysis revealed that Mn had detected on the surface ZnS:Mn etched in $BCl_3/Ar$ plasma.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.509-509
• /
• 2011

Superhydrophobic surfaces on alloyed steels were fabricated with a non-conventional method of plasma etching and subsequent water immersion procedure. High aspect ratio nanopatterns of nanoflake or nano-needle were created on the steels with various Cr content in its composition. With CF4 plasma treatment in radio-frequence chemical vapor deposition (r.-f. CVD) method, steel surfaces were etched and fluorinated by CF4 plasma, which induced the nanopattern evolution through the water immersion process. It was found that fluorine ion played a role as a catalyst to form nanopatterns in water elucidated with XPS and TEM analysis. The hierarchical patterns in micro- and nano scale leads to superhydrophobic properties on the surfaces by deposition of a hydrophobic coating with a-C:H:Si:O film deposited with a gas precursor of hexamethlydisiloxane (HMDSO) with its lower surface energy of 24.2 mN/m, similar to that of curticular wax covering lotus surfaces. Since this method is based on plasma dry etching & coating, precise patterning of surface texturing would be potential on steel or metal surfaces. Patterned hydrophobic steel surfaces were demonstrated by mimicking the Robinia pseudoacacia or acacia leaf, on which water was collected from the humid air using a patterned hydrophobicity on the steels. It is expected that this facile, non-toxic and fast technique would accelerate the large-scale production of superhydrophobic engineering materials with industrial applications.

• 마이크로전자및패키징학회지
• /
• 제8권3호
• /
• pp.63-67
• /
• 2001

최근가지 Pt박막의 식각은 Cl 계열의 가스에 의한 물리적인 스퍼터링 기구에 초점을 맞추어 연구가 진행되어왔으며 F 계열의 가스에 의한 식각 특성은 상당히 미진하였다. 본 연구에서는 ECR(electron cyclotron resonance) 플라즈마 식각 장비를 이용하여 $Cl_2$/Ar 가스와 $SF_{6}$/Ar 가스를 사용하여 Pt 박막의 식각 특성을 연구하였고, $SF_{6}$/Ar 가스의 경우 Pt 박막과 반응하여 휘발성의 식각 부산물을 형성시킬 수 있음을 확인하였다. 그리고 휘발성있는 platinum fluoride 화합물의 형성에 의해 식각률, 식각 측면형상과 표면 거칠기 특성개선도 얻을 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 학술대회 및 기술세미나 논문집 디스플레이 광소자
• /
• pp.49-51
• /
• 2006

OLEOs was fabricated by PLD method. Wet etching process and plasma treatment of ITO on the glass were performed to extend the lifetime of the OLED and increase its brightness. The NPB, $Alq_3$, Li-Benzoate and AI layers on ITO pattern on the glass were deposited by PLO method, sequentially. When the etched ITO was treated by $O_2$ plasma with RF power of 50W, the best result was obtained. The lifetime of the OLED treated by $O_2$ plasma was extended from 3,770sec to 12,586sec compared to that without the plasma treatment.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.62-65
• /
• 2001

$SrBi_2Ta_2O_{9}$ thin films were etched in inductively coupled $Cl_{2}$/$CF_{4}$/Ar plasma. The maximum etch rate was 1060 $\AA\textrm{m}$/min in $Cl_{2}$/$CF_{4}$/Ar (80). The chemical reactions on the etched surface were studied with x-ray photoelectron spectroscopy. The etching of SBT thin films in $Cl_{2}$/$CF_{4}$/Ar were etched by chemically assisted reactive ion etching. The small addition of $Cl_2$ into $CF_4$(20)/Ar(80) plasma will decrease the fluorine radicals and the increase Cl radical.