• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.2
• /
• pp.126-129
• /
• 2006

We investigated an optimized condition of the capacitor threshold voltage implantation(capacitor $V_T$ Implant) in planar P-MOS DRAM Cell. Several samples with different condition of the capacitor $V_T$ Implant were prepared. It appeared that for the capacitor $V_T$ Implant of $BF_2\;2.0{\times}l0^{13}\;cm^{-2}$ 15 KeV, refresh time is three times larger than that of the sample, in which capacitor $V_T$ Implant is in $BF_2\;1.0{\times}l0^{13}\;cm^{-2}$ 15 KeV. Raphael simulation revealed that the lowed maximum electric field and lowed minimum depletion capacitance ($C_{MIN}$) under the capacitor resulted in well refresh characteristics.

• ETRI Journal
• /
• v.28 no.4
• /
• pp.529-532
• /
• 2006

This letter describes a compact printed helical resonator and its application to a microwave oscillator circuit implemented in coplanar waveguide (CPW) technology. The high quality (Q)-factor and spurious-free characteristic of the resonator contribute to the phase noise reduction and the harmonic suppression of the resulting oscillator circuit, respectively. The designed resonator showed a loaded Q-factor of 180 in a chip area of only 40% of the corresponding miniaturized hairpin resonator without any spurious resonances. The fully planar oscillator incorporated with this resonator showed an additional phase noise reduction of 10.5 dB at a 1 MHz offset and a second harmonic suppression enhancement of 6 dB when compared to those of a conventional CPW oscillator without the planar helical resonator structure.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.8
• /
• pp.914-922
• /
• 1999

A study on the improvement of tracking performance of a 3 DOF planar parallel manipulator is performed. A class of adaptive tracking control sheme is designed using self tuning adaptive fuzzy logic control theory. This control sheme is composed of three classical PD controller and a multi learning type self tuning adaptive fuzzy logic controller set. PD controller is tuned roughly by manual setting a priori and fuzzy logic controller is tuned precisely by the gradient descent method for a global solution during run-time, so the proposed control scheme is tuned more rapidly and precisely than the single learning type self tuning adaptive fuzzy logic control sheme for a local solution. The control performance of the proposed algorithm is verified through experiments.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.295-298
• /
• 2005

In General, post-installed dowel bars are used as a shear connector to ensure the composite actions between new slabs and existing slabs in an apartment remodelling constructions expecially for enlarging the interior space outward the existing buildings. But, it has not been checked that the connection performance between existing and new slab is satisfactory not only for the structural safety condition but also the for serviceability and dwelling requirements. In this research, an experimental works were presented to evaluate the load transfer capacity for the planar joints between existing and new slab. The existing slabs were obtained from the existing apartment housing which will be demolished. Test results showed that the planar joints with post-installed dowel bars behaved in full composite modes until ultimate capacity of test specimens, so sufficient ultimate and serviceability performance are confirmed.

• Journal of the Korean Ceramic Society
• /
• v.36 no.9
• /
• pp.946-953
• /
• 1999

The etching characteristics of Er-doped sodium borosilicate glass film for the planar optical waveguides were investigated using reactive ion etching. The etch rate decreased as the pressure in creased but increased as the RF power increased. The etch rate increased as the flow rate C2F gas and the amount of O2 addition increased but decreased over critical point (C2F6 7,5 accm O2 20%) The etch rate was 180${\AA}$/min under C2F6 7.5 sccm O2 20% RF power 270 W, pressure 150 mTorr. With this optimum etching condition and subsequent heat treatment at 975$^{\circ}C$ for 30 minutes planar optical waveguides having improved sidewall roughness were fabricated successfully.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.647-650
• /
• 1989

The driving-point impedance of the center-fed planar dipole antenna is obtained using the method of moments (MOM). For the thin dipole antenna, our numerical result is compared with that of the inverse method by D. R. Rhodes as well as the known solutions of equivalent wire antenna. For the frequencies of L-band and S-band, the driving-point impedances of the thick planar dipole antennas are measured by experiment and compared with the numerical results.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.11
• /
• pp.582-588
• /
• 2006

This paper presents the characteristics analysis and normal force minimization of a synchronous permanent magnet planar motor(SPMPM) with Halbach magnet way. Firstly, the flux density distribution is calculated by analytical method; then, the characteristics of this SPMPM are evaluated, some experiments have been done to verify the analysis propriety and to investigate the interaction among the characteristics; At last, the normal force is minimized by using genetic algorithm and it is decreased from 672.83[N] to 144.24[N] remarkably.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.12
• /
• pp.1106-1110
• /
• 2005

We fabricated (110) silicon hard master by using anisotropic wet etching for embossing. The etching chemical for the silicon wafer was a TMAH $25\%$ solution. The anisotropic wet etching produces a smooth sidewall surface and the surface roughness of the fabricated master is about 3 nm. After spin coating an organic-inorganic sol-gel hybrid material on a silicon substrate, we employed hot embossing technique operated at a low pressure and temperature to form patterns on the silicon substrate by using the fabricated master. We successfully fabricated the multi-mode planar optical waveguides showing low propagation loss of 0.4 dB/cm. The surface roughness of embossed patterns was uniform for more than 10 times of the embossing processes with a single hydrophobic surface treatment of the silicon hard master.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.206-209
• /
• 2002

With the progress of semiconductor processing technology, avalanohe photodiodes (APDs) based on InP/InGaAs are used for high-speed optical receiver modules. Planar-type APDs give higher reliability than mesa-type APDs. However, Planar-type APDs are struggled with a problem of intensed electric field at the junction curvature, which causes edge breakdown phenomena at the junction periphery. In this paper, we focused on studying the effects of junction curvature for APDs performances by different etching processes followed by single diffusion to from p-n junction. The performance of each process is characterized by observing electric field profiles and carrier generation rates. From the results, it can be understood to predict the optimum structure, which can minimize edge breakdown and improve the manufacturability.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1817-1819
• /
• 2001

For an efficient calculation of scattering matrix of planar transmission line with step discontinuity. Mode Matching Method combined with Vector Finite Element Method is adopted. Calculating effective widths are replaced with their respective equivalent planar waveguide corresponding to the microstrip width, Propagation Constant is calculated from the Vector finite element. Mode matching method is used for deriving scattering parameters.