• 한국정밀공학회지
• /
• 제27권3호
• /
• pp.127-134
• /
• 2010

Components in thermal power plants are subjected to service conditions under which creep damages take place causing material exhaustion. Comprehensive creep damage investigations have been performed on a 0.5Cr0.5Mo0.25V pipe bend which had been taken out of service after 117,603h and 501 start-ups because of severe cracks. The propagation of creep damage in a long term exposed pipe bend has been analysed by the replication, Indentation and hardness tests. Also, Calculation of creep lifetime has been investigated in order to verify actual lifetime of a damaged pipe bend. By measuring diametrical expansion, Accumulated creep strain and creep strain rate were calculated. Calculated results of creep lifetime on the Larson-Miller Parameter method are good agreement with actual service-exposed hour.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2005년도 춘계학술발표회
• /
• pp.501-502
• /
• 2005

During the cut and dismantling process of HANARO irradiated instrumented capsule(03M-06U), a little different phenomenon like a jamming was observed and occurred. So to release jamming between outer pipe and inner thermal media, the outer pipe will be cut piece by piece by capsule cutting machine installed in M2 hot cell until the outer pipe was eliminated or reduced as we could. It is assumed that this kind of problem was occurred following reasons: 1) This capsule has probably a problem during manufacturing process at shop before irradiation. 2) The gap between outer pipe and thermal media is not enough to meet design criteria for thermal expansion during irradiation at HANARO

• 한국지반신소재학회논문집
• /
• 제12권1호
• /
• pp.73-81
• /
• 2013

이 연구에서는 열 수송관로 직선부에서 마찰계수의 증가를 통해 관로의 최소 설치길이를 감소시켜, 현장 시공 시 매설깊이의 증가를 억제하고, 충분한 마찰력을 제공함으로써 신축이음관의 설치를 줄여 효율적인 시공이 가능토록 함과 동시에, 곡선부에서는 마찰계수의 감소를 통해 신축흡수재의 수명 연장을 도모하여 열 수송관로의 유지관리의 효율성을 향상시키고자 하는 목적으로, 현재 주로 사용되고 있는 되메움재인 강모래보다 큰 내부마찰각을 가진 되메움재와 작은 내부마찰각을 가진 되메움재를 개발하였다. 곡관부에 타이어 분말 혼합 되메움재를 사용할 경우, 관경이 커질수록 신축흡수재에 가해지는 마찰력의 감소 경향은 증가하고 있는 것으로 나타났고, 관경 900mm에서의 마찰력은 약 38% 감소를 보였다. 강모래+fly-ash 혼합 되메움재를 사용할 경우, fly-ash 혼합비 1.5%에서 최소 설치길이의 감소효과는 약 30%, fly-ash 혼합비 3%에서 최소 설치길이의 감소효과는 약 50%로 나타나고 있어, 열 수송관로의 효율적인 시공 및 유지관리가 가능할 것으로 판단된다.

• 동력기계공학회지
• /
• 제13권4호
• /
• pp.11-17
• /
• 2009

This paper deals with the effects of pulsating flow on volumetric efficiency, which may be generated during the gas exchange procedure, due to piston motion, valve event on intake and exhaust stroke and unsteady flow of turbocharger of a three-cylinder four stroke turbo-charged diesel engine. Consequently, volumetric efficiency affects significantly the engine performance; torque characteristics, fuel economy and further to emission and noise level. As the expansion ratio became larger the engine speed varies and torque increases, the pressure pulsation in an exhaust gas pipe acts as an increasing factor of intake air charging capacity totally. The phase and amplitude of pressure pulsation in the intake system only affects volumetric efficiency favorably, if it is well matched and tuned effectively to the engine. Thus, to verify the exact phase and amplitude of the pressure variation is the ultimate solution for the air-flow ratio assessment in the intake stroke. Some experimental results of pressure diagrams in the intake pipe and gas-flow of turbine in-outlet are presented, under various kinds of operating condition.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.662-667
• /
• 2009

The research are performed to check the characteristics of the ice slurry transport system for the district cooling. The system are installed at the 1st floored building which is as large as the $1204\;m^2$ ($86\;m{\times}14\;m$), and the pumping power and branching characteristics are measured by transporting of the ice slurry. The ice slurry transporting pipe is as long as 200 m. For the same cooling load, the higher IPF is, the lower the transporting flow rate and the pumping power are. But when the IPF is higher than 15%, no less decrease of the pumping power does happen. For the branching characteristics, through the branch pipe where the flow resistance is higher, the higher IPF is measured. A little higher IPF is measured at the thermal expansion branch.

• Corrosion Science and Technology
• /
• 제21권4호
• /
• pp.243-249
• /
• 2022

The objective of the present study was to perform failure analysis of double-layered bellow (expansion joint), a core part of stress reliever, used to relieve axial stresses induced by thermal expansion of heat-transport pipes in a district heating system. The bellow underwent tensile or compressive stresses due to its structure in terms of position. A leaked position sufferred a fatigue with a tensile component for decades. A cracked bellow contained a higher fraction of martensitic phase because of manufacturing and usage histories, which induced more brittleness on the component. Inclusions in the inner layer of the bellow acted as a site of stress concentration, from which cracks initiated and then propagated along the hoop direction from the inner surface of the inner layer under fatigue loading conditions. As the crack reached critical thickness, the crack propagated to the outer surface at a higher rate, resulting in leakage of the stress reliever.

• 오토저널
• /
• 제15권1호
• /
• pp.45-54
• /
• 1993

The reattachment lengths of the Non-Newtonian fluid are investigated in the sudden expansion pipes whose ratios are 2.316 and 3.368, and the range of the Reynolds numbers is 100-30000. The reattachment lengths for the viscoelastic fluid in the laminar flow region are found to be much shorter than those of the Newtonian fluid, and decrease significantly with the increase of the concentration of viscoelastic fluid is two or three times longer than those of water, and gradually increases with the increase of the concentration of viscoelastic fluid.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권5호
• /
• pp.42-51
• /
• 2000

The performances of the simple expansion, perforated tube, and conical-connector type as an exhaust muffler are shown in this study. Applying a model in which the method of four-pole parameter is used makes theoretical estimation of the insertion loss. Experiment is performed for the measurement of the insertion loss under four cases according to the variation of the tail pipe length. By comparing the theoretical prediction with the experimental results, the validity of the modeling using the method of four-pole parameter is verified. The personal computer simulation programs for the above mentioned theory on the muffler design have been developed and exhaust sound level measurements have been carried out for simple expansion muffler, conical-connector muffler, perforated tube mufflers and the combined type of conical-connector and simple expansion muffler. The measured results for attenuation characteristics of noise for each muffler are compared with the computed theoretical results to verity the confidence and applicable limits of the theoretical equation derived.

• 한국소음진동공학회논문집
• /
• 제21권7호
• /
• pp.665-673
• /
• 2011

Simplified formulae for axial and bending natural frequencies of a bellows are developed using an equivalent thin-walled pipe model. The axial and bending stiffness of bellows is determined using lumped transfer matrix method. Transfer matrix method which includes the rotary inertia is used to calculate the natural frequencies for axial and lateral vibration. The result from the simplified formula are verified by those from as experiment result and a finite element analysis. This comparisons show good agreement with the each other.

• 소음진동
• /
• 제9권2호
• /
• pp.340-347
• /
• 1999

The acoustic performance of reactive type single expansion chamber can be calculated theoretically by plane wave theory. But higher order model should be considered to widen the frequency range. Mode matching method has been developed to consider higher order modes, but very complicated algebra should be used. Munjal suggested a numerical collocation method, which can overcome the shortcomings of mode matching method, using the compatibility conditions for acoustic pressure and particle velocity at the junctions of area discontinuities. But the restriction of Munjal's method is that the ratio between the area of inlet(or outlet) pipe and that of chamber must be natural number. In this paper, the new method was suggested to overcome the shortcomings of Munjal's method. The predictions by this method was also compared with those by the finite element method and Munjal's method in order to demonstrate the accuracy of the modified method presented here.