• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.12
• /
• pp.6967-6972
• /
• 2014

Assembly using a bolt and nut, and rivet or pin have been used widely for forming mechanical joints. The indent method is an easier process than other manufacturing techniques and the toughness of the material is excellent. On the other hand, there are many cases in which the cracks occur on the manufacturing process as the indent method. Therefore, two kinds of models, in which a pin goes into and out PCB plate in this study were developed using the CATIA program and finite element methods were performed using the ANSYS program. When a pin was passed through a PCB plate in cases 1 and 2, the maximum loads applied to the PCB plate were 79.708N and 90.277N, respectively. When the PCB plate came out of the pin in cases 1 and 2, the maximum loads were 63.783N and 33.75N, respectively. The damage prevention and durability can be improved by applying the study results to the design of real indentation.

• Clean Technology
• /
• v.14 no.4
• /
• pp.265-270
• /
• 2008

In this study, the flow and heat transfer of the aligned pin-fin array of the air cooling module for electronic packaging application were numerically analyzed with various fin shapes. The geometric cross-sectional shapes of pin-fins considered in this study were ellipse, wing and circle. The fins had same cross-sectional area and height, but they had different surface areas. As the results, the surface area, the heat transfer coefficient, and the heat transfer performance of pin-fins greatly depended on their shapes. Of the three types of pin-fins, the wing type pin-fin with suitable shape produced the best heat transfer performance. This result implies that the cooling capacity of the pin-fin cooler can be significantly enhanced only by the change of fin shape without increasing air flow-rate or fin density.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.4
• /
• pp.58-65
• /
• 2008

Most connections for the glulam structural members consisted of connector and fastener. The mechanical behaviour of the connection can be occurred by the dowel bearing resistance and wood shear by the fastener. This study aims at the examination of the shear properties for the small specimen with lamination components and for the full-sized pin connection and the moment resisting property for the double shear full-sized pin connection using structural column and beam members. Small specimens including glue line shows greater density and shear strength by the lamination effect than other specimens. It is needed that estimations of double shear property and moment resistance for the pin connections should be adjusted in some degree. For the better and safe estimation of moment resistance strength for the column-beam pin connection, however, the shear strength of small specimens should be deducted by 10%.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.225-226
• /
• 2010

• Proceedings of the Optical Society of Korea Conference
• /
• 1991.06a
• /
• pp.135-138
• /
• 1991

A planar type PIN photodiode has been fabricated and discussed. We used OMVPE systems to grow the structure of u-InP/u-InP/n-InP. P-n junction was formed by Zn-diffusion method at 50$0^{\circ}C$, for 5 minitues. The device characteristics at 5V were as follows: Dark currents were distributed around 1nA. Capacitance was 1.6pF and responsivity was above 0.85 mA/mW for 1.3${\mu}{\textrm}{m}$ wavelength. Measured cut-off frequency(-3dB) at -5V was 1.1㎓.

• Journal of Industrial Technology
• /
• v.27 no.B
• /
• pp.71-75
• /
• 2007

A cylindrical pin fin with variable diameter is analyzed by using the one dimensional analytical method. Heat loss and fin efficiency are presented as a function of the fin diameter, length and convection characteristic numbers ratio. The relationship between the fin diameter and convection characteristic number over the fin for the same amount of heat loss is shown. One of the results indicates the fin efficiency increases as the fin diameter increases while that decreases as the fin length increases.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.196-200
• /
• 1989

The physical properties related to the GaInAs/InP crystal grown by LPE are discussed in terms of both the design and operation characteristics of the GaInAs/InP Pin photodiode has cutoff frequency of 358 MHz and responsivity, 0.53 A/W (λ=1.3${\mu}{\textrm}{m}$), with dark current density as low as 4$\times$10-4/$\textrm{cm}^2$ under reverse bias voltage of 5V.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.7
• /
• pp.769-777
• /
• 2010

In this paper, a switchable circularly polarized microstrip patch antenna using PIN diodes and corner slots on ground plane is proposed at 2.4 GHz. The proposed antenna has a square microstrip patch and ground plane that consists of two pair of slots and PIN diodes. The electrical lengths of the slots are adjusted by using the switching characteristic of the PIN diode, so the polarization of the proposed antenna can be switchable between linear, left-handed(LH) and right-handed(RH). By separating the ground plane for the DC bias, the size reduction effect is also obtained. When the proposed antenna is operated as linear polarization, the return loss and impedance bandwidth are 15 dB, 59 MHz, and when operated as LH and RH polarization, the minimum axial ratio and 3-dB axial ratio bandwidth are 1.17 dB, 1.67 dB, 28 MHz, and 32 MHz, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.3
• /
• pp.258-265
• /
• 2014

By replacing the previous metal connector on the joints of timber structure, the GFRP reinforced laminated wooden pin was produced using a wooden material and Glass fiber reinforced plastic(GFRP) composite laminate. In addition, using the reinforced wooden pin, the tensile type shear strength test was conducted. Based on the result of the bending strength test of the reinforced laminated wooden pin according to the GFRP arrangement, a specimen(Type-A) with a single insertion of GFRP for each layer have shown the most favorable performance. Also, it was verified that densified specimen hot pressed for an hour at the temperature of $150^{\circ}C$ and with the oppression pressure $1.96N/mm^2$ have shown the improved performance of 1.57 times than the specimen without the densification. And in the bending strength test considering the load direction, edgewise have shown a higher performance of 3.51 times than the flatwise. A shear strength test was conducted using the Type-A reinforced laminated wooden pin which have shown a moderate performance on the test. Based on the test conducted by differentiating the type of the joint plate and the connector, compared to the specimen(Type-DS) applied with the drift pin and steel plate, the specimen( Type-WL) applied with the GFRP reinforced laminated wooden pin and GFRP reinforced wooden laminated plate have shown 1.12 times higher shear strength and also have shown an excellent toughness even after the maximum load.

• Food Science and Preservation
• /
• v.6 no.3
• /
• pp.313-318
• /
• 1999

The Properties of rice flour and consumed electricity to make rice flour were compared among three different process ; 1. roll mill after soaking rice in water, 2. roll mill after tempering, 3. try pin mill. When rice was milled by roll mill and pin-milled after tempering for 10 hrs(TRPMR), consumed electricity and moisture content of rice flour were the least. Particle size of rice flour prepared with TRPMR was 87.4% of 100 mesh or more which was the highest number among the rice flour prepared using different processes. Gelatinization temperature of the rice flour was 63.2$^{\circ}C$ and was 1.3$^{\circ}C$ lower than that of rice flour prepared with other processes. Viscosity of the rice flour prepared by TRPMR was the least. Whiteness of the rice flour prepared by TRPMR was similar to that of wheat flour.