• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.753-756
• /
• 1992

The piezoelectric ceramics of PMS-PZT was made in the radial mode disk. As the results, in the application of filter required conditions: that is, higher-values for piezoelectric properties($K_p$, $Q_m$) and lower-values for stabilities of $F_{\tau}$(temp. coefficient, aging rate), 5PMS-51PT-44PZ composition statified well. This composition was made in the dot-ring type. Asthe results, with increasing $n^2$ both $Q_m$ and S had high values, decreasing $n^2$ both $K_p$ and BW had low values when the diameter of sintered bodies were constant. Therefore, curve of filter characteristic have sharped with increasing $n^2$ and BW broadened with decreasing $n^2$.

• Journal of Mechanical Science and Technology
• /
• v.17 no.11
• /
• pp.1650-1658
• /
• 2003

This paper deals with a novel shunt circuit, which is capable of suppressing multimode vibration amplitudes by using a pair of piezoceramic patches. In order to describe the characteristic behaviors of a piezoelectric damper connected with a series and a parallel resistor-negative capacitor branch circuit, the stiffness ratio and loss factor with respect to the non-dimensional frequency are considered. The mechanism of the shunt damper is also described by considering a shunt voltage constrained by shunt impedance. To obtain a guideline model of the piezo/beam system with a negative capacitive shunting, the governing equations of motion are derived through the Hamilton's principle and a piezo sensor equation as well as a shunt-damping matrix is developed. The theoretical analysis shows that the piezo/beam system combined with a series and a parallel resistor-negative capacitor branch circuit developed in this study can significantly reduce the multiple-mode vibration amplitudes over the whole structural frequency range.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.703-706
• /
• 2002

Piezoelectric thin film such as ZnO and AlN can be applicable to FBAR (Film Bulk Acoustic Resonator) device of thin film type and FBAR can be applicable to MMIC. The characteristic of FBAR device is variable according to the deposition conditions of piezoelectric thin film when preparation of thin film by sputtering method. In this study, we prepared ZnO thin film for FBAR using Facing Targets Sputtering apparatus which can be deposited fine Quality thin film because temperature increase of substrate due to the bombardment of high-energy particles can be restrained. And crystalline and c-axis preferred orientation of ZnO thin film with deposition conditions was investigated by XRD.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.12
• /
• pp.597-600
• /
• 2002

Film Bulk Acoustic wave Resonator (FBAR) using thin piezoelectric films can be made as monolithic integrated devices with compatibility to semiconductor process, leading to small size and low cost, high Q RF circuit elements with wide applications in communications area. This paper presents a MMIC compatible suspended FBAR using surface micromachining. Membrane is composed $Si_3N_4SiO_2Si _3N_4$ multi layer and air gap is about 50${\mu}{\textrm}{m}$. Firstly, We perform one dimensional simulation applying transmission line theorem to verify resonance characteristic of the FBAR. Process of the FBAR is used MEMS technology. Fabricated FBAR resonate at 2.4GHz, $K^2_{eff}$ and Q are 4.1% and 1100.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1224-1231
• /
• 2003

This paper reports on the air-gap type thin film bulk acoustic wave resonator(FBAR) using ultra thin wafer with thickness of 50$\mu\textrm{m}$. It was fabricated to realize a small size devices and integrated objects using MEMS technology for flexible microsystems. To reduce a error of experiment, MATLAB simulation was executed using material characteristic coefficient. Fabricated thin FBAR consisted of piezoelectric film sandwiched between metal electrodes. Used piezoelectric film was the aluminum nitride(AlN) and electrode was the molybdenum(Mo). Thin wafer was fabricated by wet etching and dry etching, and then handling wafer was used to prevent damage of FBAR. The series resonance frequency and the parallel frequency measured were 2.447㎓ and 2.487㎓, respectively. Active area is 100${\times}$100$\mu\textrm{m}$$^2$.Q-factor was 996.68 and K$^2$$\_$eff/ was 3.91％.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1288-1290
• /
• 2004

Fluorescent lamp ballast using piezoelectric transformer were fabricated and its characteristic was investigated. Traditional electronic ballast is composed of basic blocks, which are composed of rectifier, power factor corrector and resonant inverter fluorescent lamp. The proposed electronic ballast has several advantages accordingly, traditional ballast was replaced fabricated electronic ballast using piezo electronic transformer and VCO oscillated, because of its lighter weight, high efficiency and saving energy.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1317-1318
• /
• 2007

On this paper, unimorph type piezoelectric vibrator made by attaching ceramic plates on rectangular elastic body, to find the basic characteristic of the actuators. In experiment, elastic body's displacement and resonance frequency were measured according to changes of ceramic's length and elastic body's length. Also, temperature changes were observed according to time. The displacement and resonance frequency were increased when the ceramic's length were increased. When elastic body's length was increased, the displacement was increased. Also, the temperature was increased according to time, but at some time it was saturated and the temperature was not increased any more.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.260-264
• /
• 1999

In this paper, the structural, dielectrial and piezoelectrical properties of 0.03Pb(Sb$\sub$1/2/Ti$\sub$0.495/)O$_3$+Xwt% MnO(x= 0, 0.3, 0.4, 0.5, 0.7) system ceramics were investigated as a function of the addition of MnO. As a result, the samples of 0.3wt% MnO content showed the highest mechanical quality factor(Qm) of 1487, and its dielectric constant and electro mechanical coupling factor(Kp) 1357, 54.3%, respectively. Therefore, the dielectrial and piezoelectrical properties of the composition ceramics were indicated as the materials suitable for piezoelectric transformer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.4
• /
• pp.325-331
• /
• 2002

In this paper, surface acoustic wave(SAW) bandpass filters using slanted finger interdigital electrode transducers(IDTs) are investigated. The slanted finger IDTs are used to design SAW filters with good shape factor, a flat passband, and good out-of-band rejection characteristic. For the filter design, input-output IDT structure was simulated with modified impulse model; uniform-withdrawal weighting IDTs, withdrawal-withdrawal weighting IDTs. SAW filters of uniform-withdrawal weighting IDTs structure were designed and fabricated on $128^{\circ}LiNbO_3$ piezoelectric substrates. Implemented SAW filter has a fractional bandwidth of 30%, center frequency of 70MHz and shape factor of $1.12\pm0.01$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.70-79
• /
• 2003

In this paper, T5 28-watt fluorescent lamp ballast using a piezoelectric transformer is fabricated and its characteristic is investigated. Developed electronic ballast is composed of basic circuits and blocks, such as rectifier part, active power factor corrector part, frequency oscillation part using microcontroller and feedback control, piezoelectric transformer and resonant half bridge inverters. The fabricated ballast uses to variable frequency methode in external so exciting that the frequency of piezoelectric transformer could be generated by voltage control oscillator using microcontroller(AT90S4433). The current of fluorescent lamp is detected by feedback control circuit. The signal of inverter output is received using Piezoelectric transformer, and then its output transmitted to fluorescent lamp. Traditional electromagnetic ballasts operated at 50-60Hz have been suffered from noticeable flicker, high loss, large crest factor and heavy weight. A new electronic ballast is operated at high frequency about 75kHz, and then Input power factor, distortion of total harmonic and lamp current crest factor are measured about 0.9!35, 12H and 1.5, respectively Accordingly, the traditional ballast is by fabricated electronic ballast using piezoelectric transformer and voltage control oscillator because of its lighter weight, high efficiency, economic merit and saving energy.