• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.1
• /
• pp.33-38
• /
• 2003

Highly homogeneous PZT powder was prepared by a partial oxalate method using chemicals of (Z $r_{0.53}$ $Ti_{0.47}$) $O_2$, Pb(N $o_3$)$_2$and (COOH)$_2$ㆍ2$H_2O$. N $b_2$ $O_{5}$ addition effect on microstructure and electrical properties of PZT ceramics was investigated. When the precursors were calcined at 71$0^{\circ}C$, a single perovskite phase was obtained. After sintering at 110$0^{\circ}C$, X-ray diffraction Patterns showed coexistence of rhombohedral and tetragonal phases regardless of the N $b_2$ $O_{5}$ content. As the content of N $b_2$ $O_{5}$ increased, grain size decreased but sintered density increased. The electromechanical coupling factor of kp and the piezoelectric constant of $d_{31}$ increased linearly with the content of N $b_2$ $O_{5}$, and those values reached 0.7 and -200, respectively, when 1.2 mol% of N $b_2$ $O_{5}$ is added. is added.ded.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1416-1418
• /
• 1994

Expressions for the displacement of a bimorph, one end fixed and the other free, has been introduced when sinusoidal inputs were applied to the ceramic plates on a thin metal plate. Maximum displacements at the free end and strains at the position of strain gage attached were measured when various wave forms, voltages, and frequencies were applied to the bimorph whose length is 6.6[cm], width 2.5[cm], and thickness 0.0365[cm]. Under the constant voltage ( $70[V_{peak}]$ ), the strains and the displacements at the free end were larger than the case of the sinusoidal input when the square wave was applied and were smaller when triangular wave. It was shown that the displacements at the free end and the strains of the gage position were increased as the applied voltage in the range of $30-90[V_{peak}]$ and effective length were increased. And it was also found that the resonant frequency of a bimorph was decreased as its effective length was increased, and that the displacements and the strains were maximum at the resonant frequency.

• Korean Journal of Optics and Photonics
• /
• v.17 no.2
• /
• pp.159-164
• /
• 2006

We demonstrate a compact optical coherence tomography(OCT) system based on the optical fiber delay line controlled by a cylindrical piezo-electric transducer(PZT). An 18-m length of single mode fiber is wrapped under constant tension around a PZT. Approximately 134 windings are used. Wraps of the long length of fiber allow the small expansion of the PZT to be magnified to an optical path length delay of 0.78 m. The OCT system shows characteristics for 2-dimensional imaging, exhibiting 96.9dB of signal-to-noise ratio(SNR), $18.6{\pm}0.5\;{\mu}m$ of axial resolution, and $5\;{\mu}m$ of lateral resolution with samples.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.3
• /
• pp.594-599
• /
• 2011

A SAW strain sensor based on Shear Horizontal wave with an 92 MHz central frequency was developed. It consists of SAW sensor, PCB substrate and bonding material (Loctite 401). External force applied to PCB substrate bonded to a piezoelectric substrate induces strain at the substrate surface, which causes changes in the elastic constant and density of the substrate and hence the propagation velocity of the SAW. The change in the velocity of the SAW result in a frequency shift of the sensor and by measuring a frequency shift, we can extract the strain induced by the external force. The $41^{\circ}$ YX $LiNbO_3$ was used because it has a Leaky shear horizontal(SH) wave propagation mode and a high electromechanical coupling coefficient ($K^2$=17.2%). And to compare with Rayleigh wave mode, $128^{\circ}$ YX $LiNbO_3$ was used. And to make a stable and low insert loss, Split IDT structure was used. The obtained sensitivity and linearity of the SAW strain sensor in the case of Split IDT were measured to be 17.2 kHz / % and 0.99, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.274-280
• /
• 1998

Polycrystalline $Sr_2Nb_2O_7$ ceramics with very high Curie temperature were sintered using the powder derived by the chemical coprecipitation method (CCP). The phase evolution and grain-orientation of sintered samples were examined by XRD, while sintering behavior, dielectric properties and polarization were studied by SEM and ferroelectric tester. Extremely high degree of grain-orientation was observed along the (0k0) direction, which resulted in anisotropic dielectric properties of the sintered samples, with the dielectric constant values approaching those for single crystal. Thin film fabrication of $Sr_2Nb_2O_7$ in the pyroniobate family was also attempted on $SiO_2$/Si(100), Pt/$SiO_2$/Si(100), Pt/Ti/$SiO_2$/Si(100) and Pt/$ZrO_2/SiO_2/Si_2(100)$ substrates, using metalorganic decomposition (MOD) process. Neodecanoate precursor solution was prepared by mixing strontium neodecanoate with niobium neodecanoate synthesized from niobium ethoxide. It was found that $Sr_2Nb_2O_7$ single phase appeared in XRD patterns the samples annealed above $950^{\circ}C$. The effect of substrate type on film microstructure and dielectric properties was observed.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.193-195
• /
• 1994

In this study, the structural, dielectric and piezoelectrical properties of $xPb(Mg_{1/2}W_{1/2})O_3-(1-x)[0.41Pb(Ni_{1/3}Nb_{2/3})O_3-0.36PbTiO_3-0.23P Zr)_3]$ (x=0, 0.01, 0.02, 0.03, 0.04, 0.05) system ceramics were investigated. The dielectric constant ${\varepsilon_{33}}^{\tau}$ at loon temperature increased up to 3mol% PMW and decreased with further PMW content. The specimen with 1mol% $Pb(Mg_{1/2}W_{1/2})O_3$, which has the ${\varepsilon_{33}}^{\tau}=5509$, kp=59[%] and $d_{33}=758{\times}10^{-12}[C/N]$, exhibits good characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.321-322
• /
• 2007

In this thesis, the sintering properties and piezoelectric properties of $Pb[(Co_{0.5}W_{0.5})_{0.03}(Ni_{1/3}Nb_{2/3})_{0.07}(Zr_{0.52}Ti_{0.48})_{0.9}]O_3+0.5[wt%]MnO_2$ ceramics has been systematically investigated as a function of the sintering temperature after manufacturing the specimens with a general method. The lattice constant from the analysis of crystal structure showed that the pychlore structure was decreased with the increase of the sintering temperature. Density was decreased by increasing $B_2O_3$. TCFr was showed its minimum variation rate of 0.35~-0.52[%] in the sintered temperature 950[$^{\circ}C$], $B_2O_3$ 3[wt%]. The electromechanical coupling coefficient (Kp) showed its maximum of 31.116[%] in the sintered temperature 1050[$^{\circ}C$], and its minimum of 20.220[%] in the sintered temperature 1150[$^{\circ}C$].

• Advances in Computational Design
• /
• v.4 no.4
• /
• pp.367-379
• /
• 2019

Multiple Inputs and Multiple Outputs (MIMO) Fuzzy logic model is developed to predict the engine performance and emission characteristics of pongamia pinnata biodiesel with hydrogen injection. Engine performance and emission characteristics such as brake thermal efficiency (BTE), brake specific energy consumption (BSEC), hydrocarbon (HC), carbon monoxide (CO), carbon dioxide ($CO_2$) and nitrous oxides ($NO_X$) were considered. Experimental investigations were carried out by using four stroke single cylinder constant speed compression ignition engine with the rated power of 5.2 kW at variable load conditions. The performance and emission characteristics are measured using an Exhaust gas analyzer, smoke meter, piezoelectric pressure transducer and crank angle encoder for different fuel blends (Diesel, B10, B20 and B30) and engine load conditions. Fuzzy logic model uses triangular and trapezoidal membership function because of its higher predictive accuracy to predict the engine performance and emission characteristics. Computational results clearly demonstrate that, the proposed fuzzy model has produced fewer deviations and has exhibited higher predictive accuracy with acceptable determination correlation coefficients of 0.99136 to 1 with experimental values. The developed fuzzy logic model has produced good correlation between the fuzzy predicted and experimental values. So it is found to be useful for predicting the engine performance and emission characteristics with limited number of available data.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.3
• /
• pp.341-350
• /
• 1996

The CdS thin films are grown on quartz plate by hot wall epitaxy. The source and substrate temperature is $590^{\circ}C$ and $400^{\circ}C$ respectively, and thickness of the film is $2.5\;\mu\textrm{m}$. Using extrapolation method of X-ray diffraction patterns for the CdS thin film, it was found hexagonal structure whose lattice constant a and c were $4.137\;{\AA}$ and $6.713\;{\AA}$, respectively. Hall effect on this sample was measured by the method of van der Pauw and studied on cattirer density and mobility depending on temperature. From hall data, the mobility was likely to be decreased by piezoelectric scattering in the temperature range 30 K to 200 K and by polar optical scattering in the temperature range 200 K to 293 K. In order to explore the applicability as a photoconductive cell we measured the sensitivity ($\gamma$), the ratio of photocurrent to darkcurrent (pc/dc), maximum allowable power dissipation (MAPD), spectral response and response time. The results indicated that for the samples annealed in Cu vapor the photoconductive characteristics are the best. Then we obtained the sensitivity of 0.99, the value of pc/dc of $9.42{\times}10^{6}$, the MAPD of 318 mW, and the rise and decay time of 10 ms and 9 ms, respectively.

• Journal of Sensor Science and Technology
• /
• v.5 no.3
• /
• pp.93-100
• /
• 1996

Polycrystalline $Sr_{2}(Ta_{1-x}Nbx)_{2}O_{7}$ and $La_{2}Ti_{2}O_{7}$ ceramics having very high Curie temperatures were synthesized by the conventional oxide mixing method (CON) and the molten salt synthesis method (MSS). Physical characteristics and phase relationship of calcined powders, as well as the sintering behavior, the grain-orientation and dielectric properties of sintered ceramics were investigated as a function of composition and firing temperature. The single $A_{2}B_{2}O_{7}$ phase was synthesized by using the MSS method at 100 - $150^{\circ}C$ lower temperature compared to the CON method. As Nb content increased in $Sr_{2}(Ta_{1-x}Nbx)_{2}O_{7}$ ceramics, the Curie temperature and the dielectric constant at Curie temperature were raised, and the sintering behavior and the degree of grain-orientation were also improved at the same time. The use of MSS-derived powders made it possible to lower the sintering temperature and to improve the dielectric properties of the sintering samples. However, the piezoelectric properties as well as the grain-orientation were not improved any further by the MSS route.