• Bulletin of the Korean Chemical Society
• /
• v.30 no.10
• /
• pp.2329-2337
• /
• 2009

Three heteroleptic ruthenium sensitizers, Ru(L)($L^1)(NCS)_2$ [L = 4,4'-dicarboxylic acid-2,2'-bipyridine, Ru-T1: $L^1$ = (E)-2-(4'-methyl-2,2'-bipyridin-4-yl)-3-(thiophen-2-yl)acrylonitrile, Ru-T2: $L^2$ = (E)-3-(5'-hexyl-2,2'-bithiophen-5- yl)-2-(4'-methyl-2,2'-bipyridin-4-yl)acrylonitrile, and Ru-T3: $L^3$ = (E)-3-(5"-hexyl-2,2':5',2"-terthiophen-5-yl)-2- (4'-methyl-2,2'-bipyridin-4-yl)acrylonitrile)], were synthesized and used as photosensitizers in nanocrystalline dyesensitized solar cells (DSSCs). The introduction of the 3-(5-hexyloligothiophen-5-yl)acrylonitrile group increased the conjugation length of the bipyridine donor ligand and thus improved their molar absorption coefficient and light harvesting efficiency. DSSCs with the configuration of Sn$O_2$: F/Ti$O_2$/ruthenium dye/liquid electrolyte/Pt devices were fabricated using these Ru-$T1{\sim}T3$ as a photosensitizers. Among the devices, the DSSCs composed of Ru-T2 exhibited highest power conversion efficiency (PCE) of 2.84% under AM 1.5 G illumination (100 mW/$cm^2$).

• Bulletin of the Korean Chemical Society
• /
• v.35 no.10
• /
• pp.3025-3029
• /
• 2014

To realize copper-based electrode materials for printed electronics applications, it is necessary to improve the adhesion strength between conductive lines and the substrate. Here, we report the preparation of Cu pastes using (3-glycidoxypropyl) trimethoxysilane (GPTMS) prepolymer as an adhesion promoter (AP). The Cu pastes were screen-printed on glass and polyimide (PI) substrates and sintered at high temperatures (> $250^{\circ}C$) under a formic acid/$N_2$ environment. According to the adhesion strengths and electrical conductivities of the sintered Cu films, the optimized Cu paste was composed of 1.0 wt % GPTMS prepolymer, 83.6 wt % Cu powder and 15.4 wt % vehicle. After sintering at $400^{\circ}C$ on a glass substrate and $275^{\circ}C$ on a PI substrate, the Cu films showed the sheet resistances of $10.0m{\Omega}/sq$. and $5.2m{\Omega}/sq$., respectively. Furthermore, the sintered Cu films exhibit excellent adhesion properties according to the results of the ASTM-D3359 standard test.

• Clean Technology
• /
• v.24 no.3
• /
• pp.249-254
• /
• 2018

In order to improve the photo conversion efficiency (${\eta}$) of dye-sensitized solar cells (DSSCs), the electrospun $TiO_2$, $SiO_2$, $ZrO_2$ and $SnO_2$ nanofibers were added into the hydrothermally prepared $TiO_2$ nanoparticles for application to a photoelectrode for DSSCs. The $TiO_2$ nanofiber added photoelectrode exhibited a higher photo current density ($J_{sc}$) compared to the bare $TiO_2$ nanoparticles, which is caused from acceleration of the transfer of excited electron from dye molecule due to the nanofiber structure. The DSSCs with $SiO_2$ nanofibers shows a higher open circuit voltage ($V_{oc}$) of 0.67 V and the highest photo conversion efficiency was found to be 6.24%.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.569-574
• /
• 2014

Inverted bulk hetero-junction polymer solar cells (iPSC) composed of P3HT/PC61BM blends on the ZnO modified with benzoic acid derivatives-based self-assembled monolayers (SAM) are fabricated. Compared with the device using the pristine ZnO, the devices with ZnO surface modified SAMs derived from benzoic acid such as 4-(diphenylamino)benzoic acid (DPA-BA) and 4-(9H-carbazol-9-yl)benzoic acid (Cz-BA) as an electron transporting layer show improved the performances. It is mainly attributed to the favorable interface dipole at the interface between ZnO and the active layer, the eective passivation of the ZnO surface traps, decrease of the work function and facilitating transport of electron from PCBM to ITO electrode. The power conversion eciency (PCE) of iPSCs based on DPA-BA and Cz-BA treated ZnO reaches 2.78 and 2.88%, respectively, while the PCE of the device based on untreated ZnO is 2.49%. The open circuit voltage values ($V_{oc}$) of the devices with bare ZnO and SAM treated ZnO are not much different. Whereas, higher the fill factor (FF) and lower the series resistance ($R_s$) are obtained in the devices with SAMs modification.

• The Journal of the Acoustical Society of Korea
• /
• v.31 no.8
• /
• pp.523-531
• /
• 2012

Recently, as a result of increasing concern about eco-friendly power, the demand for the power stations using environmentally friendly powers such as photovoltaic energy, wind force, tidal power, and tidal current has been increasing worldwide. Among these power stations tidal current power plant requires strong current generated by the topographic characteristics of the ocean floor. Uldolmok waterway producing very strong current is an ideal location for a tidal current power generation. However the occurrence of anthropogenic underwater noise generated by the tidal current power station may affect the marine environment. Therefore, it is necessary to evaluate the noise radiated from the station and predict the range influenced by the radiated noise. In this paper, the measurements of radiated noise spectrum level by the tidal current power station are presented, and the source level per unit area is estimated. Finally, the propagation properties of the radiated noise in the Uldolmok waterway is evaluated from the model simulation using the parabolic equation method, RAM.

• Electrical & Electronic Materials
• /
• v.8 no.5
• /
• pp.619-625
• /
• 1995

Polycrystalline CdTe thin film has been studied for photovoltaic application due to the 1.45 eV band gap energy ideal for solar energy conversion and high absorption coefficient. The formation of low resistance contact to p-CdTe is difficult because of large work function(>5.5eV). Common methods for ohmic contact to p-CdTe are to form a p+ region under the contact by in-diffusion of contact material to reduce the barrier height and modify a p-CdTe surface layer using chemical treatment. In this study, the surface chemical treatment of p CdTe was carried out by H$\_$3/PO$\_$4/+HNO$\_$3/ or K$\_$2/Cr$\_$2/O$\_$7/+H$\_$2/SO$\_$4/ solution to provide a Te-rich surface. And various thin film contact materials such as Cu, Au, and Cu/Au were deposited by E-beam evaporation to form ohmic contact to p-CdTe. After the metallization, post annealing was performed by oven heat treatment at 150.deg. C or by RTA(Rapid Thermal Annealing) at 250-350.deg. C. Surface chemical treatments of p-CdTe thin film improved metal/p-CdTe interface properties and post heat treatment resulted in low contact resistivity to p-CdTe.Of the various contact metal, Cu/Au and Cu show low contact resistance after oven and RTA post-heat treatments, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.102-107
• /
• 2003

This study puts focus on the optimization of growth temperature of CIGS absorber layer which affects severely the performance of solar cells. The CIGS absorber layers were prepared by three-stage co-evaporation of metal elements in the order of In-Ga-Se. The effect of the growth temperature of 1st stage was found not to be so important, and 350$^{\circ}C$ to be the lowest optimum temperature. In the case of growth temperature at 2nd/3rd stage, the optimum temperature was revealed to be 550$^{\circ}C$. The XRD results of CIGS films showed a strong (112) preferred orientation and the Raman spectra of CIGS films showed only the Al mode peak at 173cm$\^$-1/. Scanning electron microscopy results revealed very small grains at 2nd/3rd stage growth temperature of 480$^{\circ}C$. At higher temperatures, the grain size increased together with a reduction in the number of the voids. The optimization of experimental parameters above mentioned, through the repeated fabrication and characterization of unit layers and devices, led to the highest conversion efficiency of 15.4% from CIGS-based thin film solar cell with a structure of Al/ZnO/CdS/CIGS/Mo/glass.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.05a
• /
• pp.110-113
• /
• 1992

$n^{+}$-p homojunction InP diodes were fabricated using thermal diffusion of Sulfur into p-type InP substrates(Zn doped, LEC grown, p=2.3${\times}$10$^{16}$c $m^{-3}$). The Sulfur diffusion was carried out at 550$^{\circ}C$, 600$^{\circ}C$, 700$^{\circ}C$ for 4 hours in a sealed quartz ampule(～2ml in volume) containing 5mg I $n_2$ $S_3$ and Img of red phosphorus. The formed junction depth was below 0.5$\mu\textrm{m}$. After the removal of diffused layer on the rear surface of the wafer, the beak ohmic contacts to the p-side were made with a vacuum evaporation of An-Zn(2%) followed by an annealing at 450$^{\circ}C$ for 5 minutes in flowing Ar gas. The front contacts were made with a vacuum evaporation of Au-Ge(12%) followed by an annealing at 500$^{\circ}C$ for 3 minutes in flowing Ar gas. The remarkable sprctral response of the cells obtained at the region of 6000-8000${\AA}$ region. The open circuit voltage $V_{oc}$ , short circuit current density $J_{sc}$ , fill factor and conversion efficiency η of the fabricated pattern solar cells(diffusion condition : at 700$^{\circ}C$ for 4 hours) were 0.660V, 14.04㎃/$\textrm{cm}^2$, 0.6536 and 10.09%, respectively.y.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.686-694
• /
• 2014

A power semiconductor device, usually used as a switch or rectifier, is very significant in the modern power industry. The power semiconductor, in terms of its physical properties, requires a high breakdown voltage to turn off, a low on-state resistance to reduce static loss, and a fast switching speed to reduce dynamic loss. Among those parameters, the breakdown voltage and on-state resistance rely on the doping concentration of the drift region in the power semiconductor, this effect can be more important for a higher voltage device. Although the low doping concentration in the drift region increases the breakdown voltage, the on-state resistance that is increased along with it makes the static loss characteristic deteriorate. On the other hand, although the high doping concentration in the drift region reduces on-state resistance, the breakdown voltage is decreased, which limits the scope of its applications. This addresses the fact that breakdown voltage and on-state resistance are in a trade-off relationship with a parameter of the doping concentration in the drift region. Such a trade-off relationship is a hindrance to the development of power semiconductor devices that have idealistic characteristics. In this study, a novel structure is proposed for the Insulated Gate Bipolar Transistor (IGBT) device that uses conductivity modulation, which makes it possible to increase the breakdown voltage without changing the on-state resistance through use of a P-floating layer. More specifically in the proposed IGBT structure, a P-floating layer was inserted into the drift region, which results in an alleviation of the trade-off relationship between the on-state resistance and the breakdown voltage. The increase of breakdown voltage in the proposed IGBT structure has been analyzed both theoretically and through simulations, and it is verified through measurement of actual samples.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.179-182
• /
• 2006

The effect of electron beam irradiation on dye sensitized solar cell (DSSC) has been studied to examine degradation of DSSC. The high-energy electron beam irradiation affects on the materials and performance of dye sensitized solar cells. We have checked the effects of electron beam irradiation of $TiO_2$ substrate with and without dye adsorption on the photovoltaic performances of resulting DSSCS and also studied the structural and electrical properties of polymers after irradiation. All solar cells materials were irradiated by electron beams with an energy source of 2MeV at different dose rates of 60 kGy, 120 kGy 240 kGy and 900 kGy and then their photoelectrical parameters were measured at 1 sun $(100 mW/cm^2)$. It was shown that the efficiency of DSSC was decreased as increasing the dose of e-beam irradiation due to lowering in $TiO_2$ crystallinity, decomposition of dye and oxidation of FTO glasses. On the other hand, the performance of solid-state DSSC with polyethylene oxide based electrolyte was improved after irradiation of e-beam due to enhancement of its conductivity and breakage of crosslinking.