• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1555-1558
• /
• 2002

This paper presents deposition and characterizations of microcrystalline silicon(${\mu}c$-Si:H) films prepared by hot wire chemical vapor deposition at substrate temperature below $300^{\circ}C$. The $SiH_4$ Concentration$[F(SiH_4)/F(SiH_4)+F(H_2)]$ is critical parameter for the formation of Si films with microcrystalline phase. At 6% of silane concentration, deposited intrinsic ${\mu}c$-Si:H films shows sufficiently low dark conductivity and high photo sensitivity for solar cell applications. P-type ${\mu}c$-S:H films deposited by Hot-Wire CVD also shows good electrical properties by varying the rate of $B_2H_6$ to $SiH_4$ gas. The solar cells with structure of Al/nip ${\mu}c$-Si:H/TCO/glass was fabricated with sing1e chamber Hot-Wire CVD. About 3% solar efficiency was obtained and applicability of HWCVD for thin film solar cells was proven in this research.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1072_1073
• /
• 2009

This paper describes the inspection techniques for photovoltaic equipments. Firstly failure case studies on solar cells were presented, and then their FMEA was carried out. Lastly several core techniques as well as the contents by the inspection items on photovoltaic equipments were also expatiated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.318-318
• /
• 2010

We present the effect of interlayers of polymer tandem solar cells on their photovoltaic performance. P-type and n-type interlayers are essential for the series-connection of the subcells and enable to form the tandem cell architecture by the solution processing. In this study, we use PEDOT:PSS, nanocrystalline $TiO_2$, and blends of semiconducting polymers and fullerene derivatives as a hole transporting layer, electron transporting layer, and photoactive layers, respectively. We show that photovoltaic performances of polymer tandem solar cells depending on various PEDOT:PSS layers with the different electric conductivity and the various $TiO_2$ layer thickness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.36-36
• /
• 2010

Currently, there are several newly developed energy resources for the future to replace petroleum resources such as hydrogen fuel cell, solar cell, wind power, and etc. Among them, solar cell has attracted a worldwide concern, because it has an enormous amount of resources. In general, a study of solar cells can be classified in to an area of bulk type and thin-film type. Inorganic solar cells based on silicon have been tremendously developed in technology and efficiency. However, since there are many lithographic steps, high processing temperature approximately $1000^{\circ}C$, and expensive raw materials, a manufacturing cost of device are nearly reaching a limit. Contrary to those disadvantages, organic solar cells can be manufactured at room temperature. Also, it has many advantages such as a low cost, easy fabrication of thin film, and possible manufacture to a large size. Because it can be made to be flexible, research and development on solar cells are actively in progress for the next generation. ever though an efficiency of the organic solar cell is low compared to that of inorganic one, a continuous study is needed. In this paper, we report optimal device structure obtained by a program simulation for design and development of highly efficient organic photovoltaic cells. we have also compared simulated results to experimental ones.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.11.2-11.2
• /
• 2010

Photovoltaic devices are promising candidates as affordable and large-area renewable energy sources, which can replace the fossil-fuel-based resources. Especially, thin film solar cells have attracted increasing research attention, since they have a great advantage of low production cost. From the physical point of view, the photovoltaic devices can provide us interesting questions, how to enhance the light absorption and the carrier collection efficiency. A lot of approaches would be possible to address these issues. We have focused on two major topics relevant to photovoltaic device physics; (1) light management using surface plasmons and (2) junction characterizations aiming at proper interface engineering. Regarding the first topic, we have investigated the influences of Ag under-layer morphology on optical properties of ZnO thin films. The experimental results suggested that coupling between the surface plasmon polaritons at the ZnO/Ag interface and excitons in ZnO should play important roles in reflectivity of the ZnO/Ag thin films, which are widely used back reflector structures in thin film solar cells. For the second topic, we have carried out scanning probe microscopy studies of Schottky junctions consisting of photovoltaic materials. Such a research is very helpful to understand the correlation between the defects (e.g., grain boundaries) and local electrical properties. We will introduce some of the recent experimental results and discuss the physical significance.

• Electronic Materials Letters
• /
• v.14 no.6
• /
• pp.712-717
• /
• 2018

In this letter, we have introduced copper chloride ($CuCl_2$) as an additive in the $CH_3NH_3PbI_3$ precursor solution to improve the surface morphology and crystallinity of $CH_3NH_3PbI_3$ films in a single solvent system. Our optimized perovskite solar cells (PSCs) with 2.5 mol% $CuCl_2$ additive showed best power conversion efficiency (PCE) of 15.22%. The PCE of the PSCs fabricated by $CuCl_2$ (2.5 mol%) additive engineering was 56% higher than the PSC fabricated with pristine $CH_3NH_3PbI_3$.

• Current Photovoltaic Research
• /
• v.10 no.1
• /
• pp.1-5
• /
• 2022

Bifacial photovoltaic (PV) technology has received considerable attention in recent years due to the potential to achieve a higher annual energy yield compared to its monofacial PV systems. In this study, we fabricated the bifacial c-Si PV module with a shingled design using the conventional patterned bifacial solar cells. The shingled design PV module has recently attracted attention as a high-power module. Compared to the conventional module, it can have a much more active area due to the busbar-free structure. We employed the transparent backsheet for a light reception at the rear side of the PV module. Finally, we achieved a conversion power of 453.9 W for a 1300 mm × 2000 mm area. Moreover, we perform reliability tests to verify the durability of our Shingled Design Bifacial c-Si Photovoltaic module.

• Korean Journal of Materials Research
• /
• v.29 no.11
• /
• pp.720-726
• /
• 2019

Recently, research on cost reduction and efficiency improvement of crystalline silicon(c-Si) photovoltaic(PV) module has been conducted. In order to reduce costs, the thickness of solar cell wafers is becoming thinner. If the thickness of the wafer is reduced, cracking of wafer may occur in high temperature processes during the c-Si PV module manufacturing process. To solve this problem, a low temperature process has been proposed. Conductive paste(CP) is used for low temperature processing; it contains Sn57.6Bi0.4Ag component and can be electrically combined with solar cells and ribbons at a melting point of $150^{\circ}C$. Use of CP in the PV module manufacturing process can minimize cracks of solar cells. When CP is applied to solar cells, the output varies with the amount of CP, and so the optimum amount of CP must be found. In this paper, in order to find the optimal CP application amount, we manufactured several c-Si PV modules with different CP amounts. The amount control of CP is fixed at air pressure (500 kPa) and nozzle diameter 22G(outer diameter 0.72Ø, inner 0.42Ø) of dispenser; only speed is controlled. The c-Si PV module output is measured to analyze the difference according to the amount of CP and analyzed by optical microscope and Alpha-step. As the result, the optimum amount of CP is 0.452 ~ 0.544 g on solar cells.

• Current Photovoltaic Research
• /
• v.4 no.2
• /
• pp.42-47
• /
• 2016

Increasing the efficiency of dye-sensitized solar cells (DSSCs) by the fabrication of new photoelectrodes (PEs) is an important challenge. This study examined the photovoltaic parameters of DSSCs composed of a $TiO_2$ PE with $WO_3$ nanoparticles (NPs). A number of PEs with the same thickness but different concentrations of $WO_3$ NPs in the $TiO_2PE$ were prepared. The morphology and structural properties of the prepared PEs were examined by field-emission scanning electron microscopy and X-ray diffraction, respectively. The effects of the $WO_3$ NPs mixing concentration on the efficiency of DSSCs were investigated under simulated solar light irradiation.

• Carbon letters
• /
• v.12 no.4
• /
• pp.194-206
• /
• 2011

Carbon nanomaterials in organic photovoltaic (OPV) cells have attracted a great deal of interest for the development of high-efficiency, flexible, and low-cost solar cells. Due to the complicated structure of OPV devices, the electrical properties and dispersion behavior of the carbon nanomaterials should be controlled carefully in order for them to be used as materials in OPV devices. In this paper, a fundamental theory of the electrical properties and dispersion behavior of carbon nanomaterials is reviewed. Based on this review, a state-of-the-art OPV device composed of carbon nanomaterials, along with issues related to such devices, are discussed.