• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.5
• /
• pp.21-33
• /
• 2012

This paper presents the new maximum power point tracking(MPPT) control of the photovoltaic(PV) module integrated converter(MIC) system considering the shadow influence. The output characteristics of the solar cell is a nonlinear and affected by a temperature, the solar radiation and influence of a shadow. Particularly, MIC system is very sensitive to the shadow influence because the capacity is very small. In order to increase an output and efficiency of the solar power generation, the maximum power point(MPP) obeying control are necessary. Conventional perturbation and observation(PO) and Incremental conductance(IC) are the method finding MPP by the continued self-excitation vibration. The MPPT control is unable to be performed by rapid output change affected by the shadow. To solve this problem, the new control algorithm of the multi-level in which the step value changes by output change is presented. In case there are the solar radiation, a temperature and shadow influence, the presented algorithm treats and compares the conventional control algorithm and output error. In addition, the validity of the algorithm is proved. through the output error response characteristics.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.4
• /
• pp.24-33
• /
• 2012

Recently, finishing materials at spandrel area, a part of curtain-wall system, are gradually forced to improve thermal insulation performance in order to enhance the building energy efficiency. Also, Building Integrated Photovoltaics(BIPV) systems have been installed in the exterior side of the spandrel area, which is generally composed of windows. Those BIPVs aim to achieve high building energy efficiency and supply the electricity to building. However, if transparent BIPV module is combined with high insulated spandrel, it would reduce the PV efficiency for two major reasons. First, temperature in the air space, located between window layer and finishing layer of the spandrel area, can significantly increase by solar heat gain, because the space has a few air density relative to other spaces in building. Secondly, PV has a characteristics of decreased Voltage(Voc and Vmp) with the increased temperature on the PV cell. For these reasons, this research analyzed a direct interrelation between PV Cell temperature and electricity generation performance under different insulation conditions in the spandrel area. The different insulation conditions under consideration are 1) high insulated spandrel(HIS) 2) low insulated spandrel(LIS) 3) PV stand alone on the ground(SAG). As a result, in case of 1) HIS, PV temperature was increased and thus electricity generation efficiency was decreased more than other cases. To be specific, each cases' maximum temperature indicated that 1) HIS is $83.8^{\circ}C$, 2) LIS is $74.2^{\circ}C$, and 3) SAG is $66.3^{\circ}C$. Also, each cases yield electricity generation like that 1) HIS is 913.3kWh/kWp, 2) LIS is 942.8kWh/kWp, and 3) SAG is 981.3kWh/kWp. These result showed that it is needed for us to seek to the way how the PV Cell temperature would be decreased.

• Ceramist
• /
• v.21 no.2
• /
• pp.75-82
• /
• 2018

In the photovoltaics (PV) industry, there were many efforts to reduce the cost of production with high efficiency. The single most important cost factor in silicon technology is the wafer, accounting presently for ~35% of the module cost. it was already shown that the solar cell efficiency can be maintained up to the thickness range of $40-60{\mu}m$. The direct production of ultra-thin silicon wafer is very attractive and numerous different techniques, such as electrochemical process, ion implantation, and epitaxial growth, have been proposed and developed in many academic and industrial laboratories.

• Journal of Korea Ship Safrty Technology Authority
• /
• s.29
• /
• pp.2-15
• /
• 2010

국제적으로 해운분야 등 온실가스 배출량 규제를 강화하고 있으며, 정부에서도 '저탄소 녹색성장'을 위한 신재생 에너지 비율을 확대 추진함에 따라 육상 녹색성장을 위한 시도는 활발히 이루어지고 있으나, 친환경 에너지를 선박에 이용한 노력은 부족한 실정이다. 또한 현재까지 연구된 태양광 시스템의 경우 기존 선박의 동력을 대체하여 추진용으로 사용하기에는 실용성이 없으므로, 기존 선박 발전시스템을 연계한 태양광 하이브리드 발전시스템의 연구개발이 필요하며, 따라서 태양광을 선박용 에너지로 활용하기 위한 선박용 하이브리드 발전 시스템 개념 설계 및 설치 기준에 대하여 고찰하고자 한다.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.1
• /
• pp.8-13
• /
• 2012

We already fabricated a proto-type HTS charging system with photovoltaic (PV) system and obtained design parameters for DC converter and HTS charging system. In order to develop the real scale charging system efficiently, we suggested a maximum power point tracking (MPPT) controller using a perturb and observe (P&O) MPPT algorithm for PV system. In this paper, we designed and simulated the MPPT controller for the real scale HTS charging system. As well as, the PV module has been analyzed by solving solar cell equivalent equations. The simulated and theoretical results presented here are being considered the next study which addresses the design and fabrication parameters.

• Journal of Navigation and Port Research
• /
• v.31 no.3 s.119
• /
• pp.229-233
• /
• 2007

This paper presents the performance of PV(Photovoltaic) system, the design of MPPT(Maximum Power Point Tracker). Output of PV power system is DC, and PV power system is linked to the DC bus. The current(I)-voltage(V) output characteristic of PV cells changes with solar irradiance and cell temperature as parameters. As various PV modules respond differently to each of the parameters cited above. Maximum output of PV modules am be achieved by MPPT(Maximum Power Point Tracker) algorithm This paper includes a discussion on the performance of PV module, MPPT algorithm and the influence of PV module angle.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.280-283
• /
• 2007

The first grid-connected, building-integrated transparent amorphous silicon photovoltaic installation has been operated since October 2004 in Yongin, Korea. The 2.2kWp transparent PV system was applied to the facade of entrance hall in newly constructed KOLON E&C R&D building. The PV module is a nominal 0.98m ${\times}$ 0.95m, 10% transparent, laminated, amorphous(a-Si) thin-film device rated at 44 Wp per module. To demonstrate the architectural features of thin film PV technologies for daylighting application, transparent PV modules are attached to the building envelope with the form of single glazed window and special point glazing(SPG) frames. Besides power generation, the 10% transmittance of a-Si PV module provides very smooth natural daylight to the entrance hall without any special shading devices for whole year. The installation is fully instrumented and is continuously monitored in order to allow the performance assessment of amorphous silicon PV operating at the prevailing conditions. This paper presents measured power performance data from the first 12 months of operation. For the first year, annual average system specific yield was just 486.4kWh/kWp/year which is almost half of typical amorphous silicon PV output under the best angle and orientation. It should be caused by building orientation and self-shading of adjacent mass. Besides annual power output, various statistical analysis was performed to identify the characteristics of transparent thin film PV system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.6
• /
• pp.618-626
• /
• 2011

Solar cell is one of the most important new renewable energy for future energy generation. This paper presents a novel two stage DC/DC converter topology for PV PCSs. The proposed converter consists of an interleaved boost converter and a two-tank LLC resonant converter which is connected in parallel in primary and series in secondary. The main idea of this topology is that the system can achieve either unilateral or bilateral operations due to the input voltage level of the PV module, which leads to a better performance. The operating schemes on the proposed converter are analyzed and described. A 2.2kW prototype product is built, tested and verified.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.4
• /
• pp.472-478
• /
• 2022

Solar energy harvesting is practiced by various nations for the purpose of energy security and environment preservation in order to reduce overdependence on oil. Converting solar energy into electrical energy through Photovoltaic (PV) module can take place either in on-grid or off-grid applications. In recent time Lithium battery is exhibiting its presence in on-grid applications but its role in off-grid application is rarely discussed in the literature. The preliminary capacity and Peukert's study indicated that the battery quality is good and can be subjected for life cycle test. The capacity of the battery was 10.82 Ah at 1 A discharge current and the slope of 1.0117 in the Peukert's study indicated the reaction is very fast and independent on rate of discharge. In this study Lithium Iron Phosphate battery (LFP) after initial characterization was subjected to life cycle test which is specific to solar off-grid application as defined in IEC standard. The battery has delivered just 6 endurance units at room temperature before its capacity reached 75% of rated value. The low life of LFP battery in off-grid application is discussed based on State of Charge (SOC) operating window. The battery was operated both in high and low SOC's in off-grid application and both are detrimental to life of lithium battery. High SOC operation resulted in cell-to-cell variation and low SOC operation resulted in lithium plating on negative electrode. It is suggested that to make it more suitable for off-grid applications the battery by default has to be overdesigned by nearly 40% of its rated capacity.

• New & Renewable Energy
• /
• v.18 no.4
• /
• pp.64-69
• /
• 2022

Double-sided photovoltaic (PV) modules have received significant attention in recent years as a technology that can achieve higher annual energy production rates than single-sided modules. The shingled technology is a promising method for manufacturing high-density and high-power modules. These modules are divided by laser and joined with electrically conductive adhesives. The output efficiency of the divided cells depends on the division pattern and the electrode pattern, making it important to understand the output characteristics. In this study, the output characteristics of large-area double-sided light-receiving shingled cells with different split patterns and electrode patterns were investigated. The M6 size, with 6 divisions in the electrode pattern, had the highest efficiency when using 142 front fingers and 146 rear fingers. The M10 size, with 7 divisions, had the highest output when using 150 fingers equally in the front and rear. The M12 size, also with 7 divisions, showed the highest output characteristics when using 192 front fingers and 208 rear fingers.