• 전기학회논문지P
• /
• 제54권3호
• /
• pp.111-118
• /
• 2005

Since the residential load is an AC load and the output of solar cell is DC power, the photovoltaic system needs the DC/AC converter to utilize solar cell. In case of driving to interact with utility line, in order to operate at unity power factor, converter must provide the sinusoidal wave current and voltage with same phase of utility line. Since output of solar cell is greatly fluctuated by insolation, it is necessary that the operation of solar cell output in the range of the vicinity of maximum power point. In this paper, DC/AC converter is three phase PWM converter with smoothing reactor. And then, feed-forward control used to obtain a superior characteristic for current control and digital PLL circuit used to detect the phase of utility line.

• 한국수소및신에너지학회논문집
• /
• 제25권3호
• /
• pp.311-318
• /
• 2014

Performance degradation of a battery in 20 kWh energy storage system (ESS) under various operating conditions was studied. And energy saving of the ESS was also monitored by connecting with 20 kW photovoltaic (PV). PV-connected ESS saved 5~7% of energy consumption in 2013 compared to that without such system in 2012. As charge-discharge cycle increased, capacity decreased and the performance degradation was glaringly obvious after 40 cycles. And as charge and discharge rate increased, the performance degradation was more serious. After 50 charge-discharge cycles, a lot of degraded product was deposited on the surface of anode and cathode electrodes, and the cathode side was more contaminated. Therefore, in order to maintain the cell performance, it was more important to protect the degradation of the cathode side.

• Current Photovoltaic Research
• /
• 제4권2호
• /
• pp.31-41
• /
• 2016

n-type PERT (passivated emitter, rear totally diffused) bifacial solar cells with boron and phosphorus diffusion as p+ emitter and n+ BSF (back surface field) have attracted significant research interest recently. In this work, the influences of wafer thickness, bulk lifetime, emitter, BSF on the photovoltaic characteristics of solar cells are discussed. The performance of the solar cell is determined by using one-dimensional solar cell simulation software PC1D. The simulation results show that the key role of the BSF is to decrease the surface doping concentration reducing the recombination and thus, increasing the cell efficiency. A lightly phosphorus doped BSF (LD BSF) was experimentally optimized to get low surface dopant concentration for n type bifacial solar cells. Pre-oxidation combined with a multi-plateau drive-in, using limited source diffusion was carried out before pre-deposition. It could reduce the surface dopant concentration with minimal impact on the sheet resistance.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 춘계학술발표대회 논문집
• /
• pp.80-85
• /
• 2008

A PVIB(Photovoltaic in Building) system is united by a constituent outer covering and can expect dual effects that reduce expenses for the establishment of a PV system. It is a profitable technology because it does not need a building as it is a stand alone PV system. This paper presents design, operational features analysis, and PCS(Power Conditioning System) of grid-connected 30kW PVIB set up on the library of Dongshin University. For a sustainable photovoltaic system in this area, the data of the PVIB system are collected and analyzed by monitoring system using LabView. PCS of the grid-connected PVIB system, also, is designed for optimal operation with characteristics suggested in this paper.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 추계학술대회 논문집
• /
• pp.238-243
• /
• 2003

The solar cells should be operated at the maximum power point because its output characteristics are greatly fluctuated on the variation of insolation, temperature and load. The output power of solar cell is DC, therefore it is necessary to install an inverter among electric power converts. The inverter have to supply a sinusoidal current and voltage to the load and the interactive utility line. In the paper, the proposes a photovoltaic system designed with a step up chopper and single phase PWM voltage source inverter. Synchronous signal and control signal was processed by microprocessor for stable modulation. The step up chopper operates in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature because solar cell has typical dropping character. The single phase PWM voltage source inverter consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be developed continuously by connecting with the source of electric power, from 10 to $20\%$. The single phase PWM voltage source inverter operates in situation that its output voltage is in same phase with the utility voltage. The inverter supplies an ac power with high factor and low level of harmonics to the load and the utility power system.

• Current Photovoltaic Research
• /
• 제6권1호
• /
• pp.27-30
• /
• 2018

The dependency of the electrical characteristics of silicon solar-cells on the depth of damaged layer induced by wire-sawing process was investigated. To compare cell efficiency with residual sawing damage, silicon solar-cells were fabricated by using as-sawn wafers having different depth of saw damage without any damaged etching process. The damaged layer induced by wire-sawing process in silicon bulk intensely influenced the value of fill factor on solar cells, degrading fill factor to 57.20%. In addition, the photovoltaic characteristics of solar cells applying texturing process shows that although the initial depth of saw-damage induced by wire-sawing process was different, the value of short-circuit current, fill-factor, and power-conversion-efficiency have an almost same, showing ~17.4% of cell efficiency. It indicated that the degradation of solar-cell efficiency induced by wire-sawing process could be prevented by eliminating all damaged layer through sufficient pyramid-surface texturing process.

• 통합자연과학논문집
• /
• 제10권1호
• /
• pp.58-63
• /
• 2017

Photovoltaic (PV) are generally modeled using mathematical equations that describe the PV system behavior. Most of the modeling approach is very simple in terms of that PV module temperature is calculated from nominal constant cell temperature such as ambient temperature and incoming solar irradiance. In this paper, we newly present MATLAB model particularly embedding the effect of wind speed to describe more accurate cell temperature. For analyses and validate purpose of the proposed model, solar power is obtained and compared with and without wind speed from the 50Wp PV module provided by vendor datasheet. In the simulation result, we found that power output of the module is increased to 0.37% in terms of cell temperature a degreed down when we consider the wind speed in the model. This result is well corresponded with the well-known fact that normal PV is 0.4% power changed by cell temperature a degree difference. Therefore it shows that our modeling method with wind speed is more appropriate than the methods without the wind speed effect.

• 전기학회논문지P
• /
• 제59권3호
• /
• pp.293-297
• /
• 2010

Next generation concentrating photovoltaic technologies could have a large-scale impact on world electricity production once they will become economically attractive and grid parity will be reached. Multi-junction solar cells will be characterised by a high value of the cell economical performance index if the cells were able to operate at high concentration level. Concentrating the sunlight by optical devices like lenses or mirrors reduces the area of expensive solar cells or modules, and, moreover, increases their efficiency. Accurate and reliable tracking is an important issue to maintain high the CPV system output power. Further, for high concentration CPV systems, the actual tracker cost is about 20% of the total CPV system cost. In this paper high-concentration is defined as systems using concentration ratios well above 100 times the one sun intensity and trackerlss CPV system studied. Using sphericalness lens and parallel MJ cell connection method were suggested and achieved experiment on a clear day in summer. Development of these high performance multi-junction CPV module promises to accelerate growth in photovoltaic power generation.

• Current Photovoltaic Research
• /
• 제3권1호
• /
• pp.16-20
• /
• 2015

Ag addition in chalcopyrite materials is known to lead beneficial changes in aspects of structural and electronic properties. In this work, the effects of Ag alloying of $Cu(In,Ga)Se_2$-based solar cells has been investigated. Wide bandgap $(Ag,Cu)(In_{1-x},Ga_x)Se_2$ (x = 0.75~0.8) films have been deposited using a three-stage co-evaporation with various Ag/(Ag+Cu) ratios. With Ag alloying the $(Ag,Cu)(In_{1-x},Ga_x)Se_2$ (x~0.8) films were found to have greater grainsize and film thickness. Device were also fabricated with the $(Ag,Cu)(In_{1-x},Ga_x)Se_2$ (x~0.8) films and their J-V and quantum efficiency measurements were carried out. The highest-efficiency $(Ag,Cu)(In_{1-x},Ga_x)Se_2$ solar cell with Eg > 1.5 eV had an efficiency of 12.2% with device parameters $V_{OC}=0.810V$, $J_{SC}=21.7mA/cm^2$, and FF = 69.0%.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2016년도 전력전자학술대회 논문집
• /
• pp.357-358
• /
• 2016

This paper presents a dynamic, electric-thermal model for a photovoltaic (PV) cell that combines electrical and thermal parameters. In this model, the irradiance and ambient temperature are used to calculate the PV cell temperature based on a five-layer thermal model. The cell temperature is then used in the electrical model to accurately adjust the PV cell output electrical characteristics and power. A custom experimental setup was built to test and verify the electrical and thermal characteristics of the PV cell and its surrounding layers. The electric-thermal model is validated using experimental data in realistic scenarios. This PV model can be scaled up and used to simulate PV systems in wide variety of applications, extreme environmental conditions, and fault conditions in real-time.