• Journal of environmental and Sanitary engineering
• /
• v.20 no.4 s.58
• /
• pp.45-50
• /
• 2005

Titania gel formations were prepared by sol-gel method using titanium(IV) chloride $(TiCl_4)$, and its characteristics were analyzed by varying the $epoxide/TiCl_4$ ratio and the amount of water In the end, titania $(TiO_2)$ aerogel were prepared using supercritical drying process. VOCs such as benzene, toluene, and m-xylene (BTX) were oxidized using prepared titania aerogel and commercially available $TiO_2$, and its performance was compared. The surface area, pore volume, and average pore diameter of 1,2-epoxybutane are significantly smaller than the propylene oxide. And the titania aerogels with 6 moi of epoxides have high surface areas, pore volumes, and average pore diameters. As a result of photo-oxidation, conversion of benzene was reached about $70\%$, and other reactants were reached about $60\%$ similarly. The conversion of BTX was increased as inlet concentration decreased. The reactivity of titania calcined at $600^{\circ}C$ was greater than $400^{\circ}C$ and $800^{\circ}C$. Water is required as a reactants for the oxidation of VOCs, and the continuous consumption of hydroxyl radicals required replenishments to maintain catalyst activity. The activity ratio increased with increasing reaction time when enough amount of water was present in the reactor.

• Journal of the Korean Ceramic Society
• /
• v.49 no.2
• /
• pp.151-154
• /
• 2012

Flower-like and plate-like CuO nanopowder has been successfully synthesized using a facile microwave-assisted synthetic route. The morphology and size of the final products strongly depended on microwave power. The phase, structures and morphologies of the as-prepared products were investigated in detail by BET surface area analysis, X-ray diffraction (XRD) analysis, and scanning electron microscopy (SEM). In addition, the chemical oxygen demand of polluted lake water was employed for characterization of these new photocatalysts. The results showed correlations between the morphology of CuO micro-crystals and their catalytic properties.

• Journal of the Korean Ceramic Society
• /
• v.45 no.3
• /
• pp.150-156
• /
• 2008

Pitch-binded activated carbon fiber(ACF)/$TiO_2$ composite photocatalysts were prepared by Carbon Tetra Chloride (CTC) solvent mixing method with different mixing ratios of anatase to ACF. The result of the textural surface properties demonstrated that there is a slight increase in the Brunauer, Emmett and Teller (BET) surface area of composites with an increase of the amount of ACF. The surfaces structure morphologies of the composites were observed using an Scanning Electron Microscope (SEM). In the XRD patterns for all ACF/$TiO_2$ composites, the diffraction peaks showed the formation of anatase crystallites. The EDX spectra showed the presence of C, O and Si with strong Ti peaks. Most of these samples were richer in carbon and major Ti metal than any other elements. From the photo-decomposition results, the excellent activity of the ACF/$TiO_2$ composites between c/$c_0$ for methylene blue and UV irradiation time could be attributed to both the effects of the photocatalysis of the supported $TiO_2$ and adsorptivity of activated carbon fiber and another carbon derived from pitch.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.2
• /
• pp.107-112
• /
• 2013

The ZnO is able to produce hydrogen from water however it can only absorb ultraviolet region due to its 3.37eV of wide band gap. Therefore efficiency of solar hydrogen production is low. In this work we report investigation results of improved visible light photo-catalytic properties of CdSe quantum dots(QDs) sensitized ZnO nanorod heterostructures. Hydrothermally vertically grown ZnO nanorod arrays on FTO glass were sensitized with CdSe by using SILAR(successive ionic layer adsorption and reaction) method. Morphology of grown ZnO and CdSe sensitized ZnO nanorods had been investigated by FE-SEM that shows length of $2.0{\mu}m$, diameter of 120~150nm nanorod respectively. Photocatalytic measurements revealed that heterostructured samples show improved photocurrent density under the visible light illumination. Improved visible light performance of the heterostructures is resulting from narrow band gap of the CdSe and its favorable conduction band positions relative to potentials of ZnO band and water redox reaction.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1256-1257
• /
• 2008

Dye-Sensitized Solar Cell(DSSC) is a new type of solar cell by using photocatalytic properties of $TiO_2$. The size and shape of $TiO_2$ particle are two of important parameters that are related to the characteristics of DSSC. And these can be changed by controlling $TiO_2$ sintering conditions especially temperature. The particles of $TiO_2$ are classified anatase and rutile. Anatase particles are created at low sintering temperature and rutile particles are created at high sintering temperature. Anatase particles have advantages such as increased surfaces that cause more attached dye molecules, and fast electron transportation. And rutile particles have advatages such as more efficient light scattering. Therefore, we studied characteristics of DSSC in this paper as $TiO_2$ sintering temperature is varied. As a result, we found that characteristics of DSSC are very good in the case that anatase and rutile particles are together and this sintering temperature is 450$^{\circ}C$.

• Environmental Analysis Health and Toxicology
• /
• v.19 no.3
• /
• pp.271-278
• /
• 2004

Epoxy resins are mostly used as a molding material for drinking water tank. Bisphenol A is used at a constituent material for epoxy resins and is widely suspected to act as an endocrine disrupter. In this study, we investigated embryo hatching in zebrafish reared in water undergone leaching process of expoxy resin, and found a decreased survival rate. Bisphenol A eluted from epoxy resin in drinking water tank was completely degraded by TiO$_2$ photocatalysis. We detected 7.8 ng/ml of bisphenol A in epoxy resin tank, and observed that the concentration was undetectable after 48h photocatalysis over TiO$_2$. There was no toxicity in hatching rates in zebrafish and morphogenesis after photocatalysis. The effect of TiO$_2$ photocatalytic reactions on the catalase activities in the f]y stage of zebrafish was also examined. At 1 week post hatching, cataiase activities were higher both in the group of epoxy resin with 48 h TiO$_2$ photocatalysis and in the TiO$_2$ photocatalysis for 48 hours were higher than control group. However catalase activities of the treatment group of epoxy resin by TiO$_2$ photocatalysis for 48 hours were similar to control in 5 weeks post hatching fries. In conclusion, the toxicity of TiO$_2$ photocatalysis was not observed in this zebrafish.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.3
• /
• pp.411-419
• /
• 2004

Titania particles are widely used as a photocatalyst to treat various contaminants in air and water. Titania particles were formed by vapor-phase oxidation of titanium tetraisopropoxide (TTIP) in a tube furnace between 773 and 1,273 K. The effect of process variables such as furnace temperature, flow rate of carrier air, and flow rate of sheath air on powder size and phase characteristics was investigated using a scanning mobility particle sizer (SMPS), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The size distribution of synthesized titania particles was characterized with mode diameter and peak concentration. The mode diameter ranging from 20 to 80 nm decreased with increasing flow rates of sheath air and carrier air, and increased with increasing furnace temperature. The peak concentration increased with increasing flow rates of sheath air and carrier air The best synthetic condition for high production rate can be derived from the experimental data set represented by mode diameter and peak concentration. The crystal structure of synthesized titania particles was found to be anatase phase, ensuring high photocatalytic potential.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2005.04a
• /
• pp.163-166
• /
• 2005

[ $TiO_2$ ] 광촉매에 의한 분해 반응의 활성을 높이기 위한 다양한 연구가 진행되었다. 광촉매 반응은 1차 반응을 따랐으며 초기농도가 높을수록 분해효율이 감소하는 경향을 보였다. 본 연구에서는 산화제로 과산화수소가 주입되었을 경우 분해효율을 조사하였으며, 과산화수소를 주입하였을 경우가 그렇지 않은 경우보다 더 높은 분해효율을 보였다. 또한 과산화수소 주입량을 달리했을 때, 주입량이 증가할수록 효율이 높아지다가 일정량 이상에서는 오히려 효율이 감소하는 것으로 나타났다. 따라서 과산화수소 최적첨가량이 존재함을 알 수 있었다. 한편 $TiO_2$에 전이금속을 첨가하여 전이금속이 $TiO_2$ 촉매의 분해효율에 미치는 영향을 알아보았다. Pt(0.5%)-$TiO_2$가 가장 높은 분해효을을 보였으며, Pt첨가함량이 더 큰 Pt(2%)-$TiO_2$는 함량이 증가했음에도 불구하고 큰 차이는 아니지만 오히려 효율이 감소하였다. 따라서 촉매표면에서 전자와 정공이 생성되었을 때, Pt가 전자를 포획함으로써 전자와 정공의 재결합율을 감소시켜 OH라디칼을 생성할 수 있는 정공이 많아져 반응효율을 증가되는 것을 알 수 있었고, 금속에 따른 최적 첨가함량이 존재함을 알 수 있다. 반면에 Pd를 첨가했을 경우는 첨가 함량에 관계없이 모두 분해효율이 오히려 감소하는 경향을 나타냈으며 이는 전이금속 고유의 성질이나, 또는 대상물질에 따라 각기 다른 경향이 존재함을 나타내며 추가적인 연구가 필요하다고 사료된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.160-160
• /
• 2011

In the present work, $TiO_2$ fiilms supported by porous silica gel with high surface area synthesized by atomic layer deposition(ALD). Porous structure of silica substrate could be maintained even after deposit large amount of $TiO_2$ (500 cycles of ALD process), suggesting the differential growth mode of $TiO_2$ on top surface and inside the pore. All the $TiO_2$-covered silica samples showed improved MB adsorption abilities, comparing to bare one. In addition, when silica surface was covered with $TiO_2$ films, MB adsorption capacity was almost fully recovered by re-annealing process (500$^{\circ}C$, for 1 hr, in ambient pressure), whereas MB adsorption capacity of bare silica was decreased after re-heaing process. FT-IR study demonstrated that $TiO_2$ film could prevent deposition of surface-bound intermediate species during thermal decomposition of adsorbed MB molecules. Photocatalytic activity of $TiO_2$/silica sample was also investigated.

• Journal of Powder Materials
• /
• v.24 no.4
• /
• pp.326-331
• /
• 2017

The structural formation of inorganic nanoparticles dispersed in polymer matrices is a key technology for producing advanced nanocomposites with a unique combination of optical, electrical, and mechanical properties. Barium titanate ($BaTiO_3$) nanoparticles are attractive for increasing the refractive index and dielectric constant of polymer nanocomposites. Current synthesis processes for $BaTiO_3$ nanoparticles require expensive precursors or organic solvents, complicated steps, and long reaction times. In this study, we demonstrate a simple and continuous approach for synthesizing $BaTiO_3$ nanoparticles based on a salt-assisted ultrasonic spray pyrolysis method. This process allows the synthesis of $BaTiO_3$ nanoparticles with diameters of 20-50 nm and a highly crystalline tetragonal structure. The optical properties and photocatalytic activities of the nanoparticles show that they are suitable for use as fillers in various nanocomposites.