• 한국환경보건학회지
• /
• 제30권5호
• /
• pp.358-365
• /
• 2004

The photocatalytic oxidation of Rhodamine B(RhB) was studied using photocatalytic reactor filled with module of quartz tube. Module of quartz tube consisted of small quartz tube (inner diameter, 1.5 mm; outer diameter, 3 mm) bundle coated with powder $TiO_2$ and uncoated large quartz tube (inner diameter, 20 mm; outer diameter, 22 mm). Two 30 W germicidal lamp was used as the light source and the reactor volume was 0.5 l. The effects of parameters such as the coating materials and numbers, initial concentration, $H_{2}O_2$ dose and metal deposition (Ag, Pt and Fe) and simultaneous application of $H_{2}O_2$ and metal deposition. The results showed that the initial reaction constant of quartz module coated with powder $TiO_2$ was higher 1.4 time than that of the $TiO_2$ sol and optimum coating number is twice. In order to increase reaction rate, simultaneous application of photocatalytic and photo-fenton reaction using Fe coating and dose $H_{2}O_2$ dose increased reaction rate largely.

• 한국재료학회지
• /
• 제13권10호
• /
• pp.691-696
• /
• 2003

To improve the photocatalyticactivity of $TiO_2$-coated coal fly ash, tungsten hydroxide was doped by impregnation method and was oxidized by heat treatment in temperature ranges of $WO^{\circ}C$ for 2 hrs. The changes of crystal structure and crystal size of $TiO_2$and $WO_3$on coal fly ash were investigated by X-ray diffraction analysis. The crystal structure of titanium dioxide showed only anatase type and $TiO_2$-$WO_3$ compounds appeared in the heat treatment temperature ranges of $500∼600^{\circ}C$. By adding $V_3$in $TiO_2$coated on fly ash, the growth of crystal size of anatase was restrained and the anatase phase was stabilized in temperature ranges of TEX>$500∼<800^{\circ}C$. And $WO_3$acted as a trap site of electrons excited from anatase by irradiating UV. The maximum removal efficiency of NO gas for $TiO_2$/$WO_3$-coated coal fly ash was 84% and appeared when the ammonium tungstate of $1.3${\times}$10^{-3}$ M was doped and then heated at $600^{\circ}C$ for 2 hrs.

• Korean Chemical Engineering Research
• /
• 제51권4호
• /
• pp.426-431
• /
• 2013

비교적 낮은 온도와 상압에서 전구체 Titanium(IV) sulfate와 염기성 용액을 반응시키는 수열합성법을 이용하여 소성과정을 거치지 않고 $TiO_2$ 나노입자를 제조하였다. 염기성 용액의 종류(NaOH, $NH_4OH$, Monoethanolamine, Diethanolamine, Triethanolamine), 첨가되는 계면활성제의 종류(CTAB, Span 20, SDBS)와 농도, 제조 온도, pH 등을 변화시켜 $TiO_2$를 제조하였고, 생성되는 입자의 결정성, 입자크기 등과 같은 물리적 특성은 XRD, SEM, Zeta-potential 등을 사용하여 분석하였다. 또한, 광촉매적 특성을 확인하기 위하여 DRS를 통해 흡광면적을 측정, 비교하였다. 침전제로 사용된 염기성 물질 중 NaOH가 결정성이 우수하고 입자크기가 작은 $TiO_2$를 제조하는데 가장 효과적임을 확인할 수 있었다. 계면활성제는 양이온성 계면활성제인 CTAB를 첨가한 경우 다른 계면활성제보다 작은 크기의 $TiO_2$를 제조할 수 있었다. 그리고 동일한 조건에서 전구체인 $Ti(SO_4)_2$와 CTAB의 농도비를 10 : 1로 조절한 경우 CTAB를 첨가하지 않은 경우보다 제조되는 $TiO_2$ 입자의 크기는 약 1/10인 5.8 nm로 감소하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.227.1-227.1
• /
• 2010

본 연구는 자외선 영역의 흡수로 전자 정공의 전하쌍을 생성함으로써 광전압 및 전류를 일으키는 티타니아 물질을 금속지지체 표면에 양극산화로 튜브형 $TiO_2$(anodized tubular $TiO_2$; ATT)로 제조한 후 나노크기의 금속 혹은 $WO_3$입자를 담지하여 광감응 재료로 활용하였다. 이는 기존의 입자나 콜로이드 형태로 광촉매 물질을 고정화하여 사용한 재료의 탈리현상 및 효율저하를 극복하기 위함이다. ATT는 전해질 내에 전기화학적 에칭율과 화학적 용해율의 비율에 의해 나노튜브 길이 성장에 영향을 미치는데 이를 유기 전해질과 불산 전해질을 사용하여 정전압 혹은 정전류의 조건에서 다양한 길이의 $TiO_2$ 나노튜브를 제조하였다. 여기에 전기분해담지(electrolytic deposition; ELD)를 통하여 정전류 조건에서 다양한 금속(Pt, Pd, Ru)을 나노크기의 형태로 담지하여 광촉매 내 생성된 전자 정공의 재결합을 줄이고자 하였고 $WO_3$의 담지를 통하여 가시광 감응을 높이고자 하였다. 제조된 여러 조건의 시료는 SEM과 EDAX를 통하여 형태와 길이, 담지량을 확인 하고 XRD를 이용하여 열처리 온도에 따른 결정화상태를 확인하였으며 광전류 측정 및 Cr(VI)의 광환원과 MB의 광분해를 통하여 광효율을 관찰하였다. 금속이 도핑되었을 경우 순수 ATT보다 보통 3배의 흡착률과 UV광원 아래 2배의 광효율을 관찰할 수 있었는데 이 중 Pt의 담지가 가장 효율이 좋았으며 흡착률에서는 담지량의 증가에 따른 증가선을 관찰 할 수 있었으나 광원 사용시 3%담지율에서 최적을 확인 할 수 있었다. 또한 $TiO_2$외 가시광감응 활성을 높이기 위한 다양한 광촉매제조가 진행 중에 있다.

• 한국분말재료학회지
• /
• 제26권3호
• /
• pp.237-242
• /
• 2019

In this study, ultrasonic spray pyrolysis combined with salt-assisted decomposition, a process that adds sodium nitrate ($NaNO_3$) into a titanium precursor solution, is used to synthesize nanosized titanium dioxide ($TiO_2$) particles. The added $NaNO_3$ prevents the agglomeration of the primary nanoparticles in the pyrolysis process. The nanoparticles are obtained after a washing process, removing $NaNO_3$ and NaF from the secondary particles, which consist of the salts and $TiO_2$ nanoparticles. The effects of pyrolysis temperature on the size, crystallographic characteristics, and bandgap energy of the synthesized nanoparticles are systematically investigated. The synthesized $TiO_2$ nanoparticles have a size of approximately 2-10 nm a bandgap energy of 3.1-3.25 eV, depending on the synthetic temperature. These differences in properties affect the photocatalytic activities of the synthesized $TiO_2$ nanoparticles.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2004년도 춘계 총회 및 학술발표회
• /
• pp.184-187
• /
• 2004

고급산화법 중 하나인 광촉매인 TiO$_2$를 이용한 시스템은 300~400nm 파장의 UV영역에서 비교적 적은 에너지로 유기 오염 물질을 $CO_2$와 $H_2O$로 산화시킨다[1]. 따라서 폐수용액 중 오염물질을 제거한 경우에도 슬러리로 인한 2차 오염의 문제가 없다. 최근에는 난분해성 물질이나 독성을 가진 물질을 포함된 폐수처리 시설의 고도처리를 위하여 분리막을 도입하는 추세이다.(중략)

• 한국재료학회지
• /
• 제14권6호
• /
• pp.407-412
• /
• 2004

Photo decomposition of gas phase benzene by $TiO_2$ thin films chemically deposited on alumina balls were investigated under UV irradiation. Photo decomposition rates were measured in real time during the reaction using a photo ionization detector, which ionizes C-H bonding of benzene molecules and then converts into volatile organic compounds (VOCs) concentrations. From the measuring results, the VOCs concentration increased instantly when IN irradiated because C-H bonds of benzene molecules strongly absorbed on the surface of $TiO_2$ films before the IN irradiation was destroyed by photo decomposition. After that, the VOCs concentration decreased with increasing surface area of $TiO_2$ and reaction time under the IN irradiation. At the optimal conditions for the photo decomposition of gas phase benzene, the reaction rate of the photo decomposition for high concentrations (over 60 ppm) was slow but that of relatively low concentration (under 60 ppm) was fast, due to limited surface area of $TiO_2$ thin films for the reaction. Thus, it is concluded that the photo decomposition rate was mainly affected by the surface area of $TiO_2$ or absorption reaction.

• 한국분말재료학회지
• /
• 제25권4호
• /
• pp.316-321
• /
• 2018

Composites of P25 $TiO_2$ and hexagonal $WO_3$ nanorods are synthesized through ball-milling in order to study photocatalytic properties. Various composites of $TiO_2/WO_3$ are prepared by controlling the weight percentages (wt%) of $WO_3$, in the range of 1-30 wt%, and milling time to investigate the effects of the composition ratio on the photocatalytic properties. Scanning electron microscopy, x-ray diffraction, and transmission electron microscopy are performed to characterize the structure, shape and size of the synthesized composites of $TiO_2/WO_3$. Methylene blue is used as a test dye to analyze the photocatalytic properties of the synthesized composite material. The photocatalytic activity shows that the decomposition efficiency of the dye due to the photocatalytic effect is the highest in the $TiO_2/WO_3$ (3 wt%) composite, and the catalytic efficiency decreases sharply when the amount of $WO_3$ is further increased. As the amount of $WO_3$ added increases, dye-removal by adsorption occurs during centrifugation, instead of the decomposition of dyes by photocatalysts. Finally, $TiO_2/WO_3$ (3 wt%) composites are synthesized with various milling times. Experimental results show that the milling time has the best catalytic efficiency at 30 min, after which it gradually decreases. There is no significant change after 1 hour.

• Korean Chemical Engineering Research
• /
• 제46권5호
• /
• pp.852-857
• /
• 2008

광촉매의 고정화는 광촉매의 이용범위를 넓히기 위해서 매우 중요한 기술이다. 광촉매를 고정화시키기 위해 티타늄 표면을 양극산화 시켜 $TiO_2$로 전환시킬 수 있다. 양극산화에 의해 제조된 $TiO_2$는 광촉매 활성을 가지고 있으며 표면은 스펀지와 비슷한 형태를 나타내었다. 다양한 초기농도, 습도, 방전전압 하에서 양극산화에 의해 티타니아를 제조 이를 이용하여 기상의 아세트알데히드와 VOC의 광촉매 분해반응을 연구하였다. 양극산화 티타니아의 반응성은 상대습도가 증가함에 따라 증가하였으나 너무 높은 습도는 반응성을 감소시켰다. 광촉매 반응과 전기 방전을 결합시키면 VOC 제거효율이 크게 증가 되었으나, 과도한 전압을 가하여 코로나 방전이 발생되면 반응속도가 오히려 감소되었다. 최적 상대습도는 40%였으며 최적 방전전압은 암방전 영역인 5 kV였다.

• 청정기술
• /
• 제28권2호
• /
• pp.147-154
• /
• 2022

Titanate nanotubes (TNTs) were synthesized via alkaline hydrothermal treatment using commercial TiO₂ nanoparticles (P25). The TNTs were prepared at various TiO₂/NaOH ratios, hydrothermal temperatures, and hydrothermal times. The synthesized catalysts were characterized by X-ray diffraction, field-emission scanning electron microscopy, N₂ adsorption-desorption isotherms, field-emission transmission electron microscopy, and ultraviolet-visible spectroscopy. TNTs were generated upon a decrease in the TiO₂/NaOH ratio due to the dissolution of TiO₂ in the alkaline solution and the generation of new Ti-O-Ti bonds to form titanate nanoplates and nanotubes. The hydrothermal treatment temperature and time were important factors for promoting the nucleation and growth of TNTs. The TNT catalyst with the largest surface area (389.32 m² g^-1) was obtained with a TiO₂/NaOH ratio of 0.25, a hydrothermal treatment temperature of 130 ℃, and a hydrothermal treatment time of 36 h. Additionally, we investigated the photocatalytic activity of methyl violet 2B (MV) over the TNT catalysts under UV irradiation and found that the degradation efficiencies of the TNTs were higher than that of P25. Among the TNT catalysts, the TNT catalyst that was hydrothermally synthesized for 36 h (TNT 36 h) exhibited a 96.9% degradation efficiency and a degradation rate constant that was 4.8 times higher than P25 due to its large surface area, which allowed for more contact between the MV molecules and TNT surfaces and facilitated rapid electron transfer. Finally, these results were correlated with the specific surface area.