• 대한치과보철학회지
• /
• 제23권1호
• /
• pp.155-164
• /
• 1985

Acrylic resin has some disadvantages in its physical properties such as a low surface hardness, being easily abraded as well as low degree of impact resistance. To overcome these disavantages, Perma Cure System was introduced in 1981, in which photo polymerizing monomers coated on acrylic resin surface were polymerized. In this study, to observe the effect of Perma Cure System on physical properties of treated surface of different types of acrylic resin, abrasion resistance, surface hardness and surface roughness of 4 different types of resin (Premium, Ortho-jet acrylic, Quick resin, Thermo jel) were tested before and after coating treatment. The conclusions arised from this study are as follows; 1. In all types of resin, the abrasion resistance of coated specimen was higher than that of uncoated specimen, and there was difference in amount of abrasion among the types of coated resin. 2. In all types of resin, the surface hardness of coated specimen was higher than that of uncoated specimen, and there was no difference in surface hardness among the types of coated resin. 3. In all types of resin, surface roughness of coated specimen was lower than that of uncoated specimen, and was different according to the degree of surface roughness before coating treatment in same sort of resin specimen.

• 한국결정성장학회지
• /
• 제29권6호
• /
• pp.345-351
• /
• 2019

디지털 잉크젯 프린팅 기술은 고해상도, 빠른 인쇄 속도, 높은 잉크 효율과 같은 장점과 함께 다양한 소재 적용이 용이하여 반도체, 디스플레이, 세라믹 타일 등의 산업 분야에서 주목을 받고 있다. 최근에는 전통적인 잉크 소재에서 벗어나 우수한 내열성, 내광성, 내화학성 등을 보이는 기능성 소재도 잉크젯 프린팅 공정에 적용하려는 시도가 활발히 진행되고 있다. 특히 2차원 인쇄뿐만 아니라 3차원 적층인쇄에 관한 연구도 시작되고 있으며 이를 위해서는 토출되는 잉크의 유변학적 물성과 프린트되는 기판과의 상호작용를 제어하는 것이 필수적이다. 본 연구에서는 나노 실리카 입자가 포함된 광경화성 세라믹 잉크를 합성하고 잉크의 물성과 프린팅 기판의 표면특성을 제어하였다. 나노 실리카 입자가 포함된 광경화성 세라믹 잉크의 퍼짐현상을 억제하고 기판과의 접촉각 특성을 개선함으로써 결과적으로 프린팅 해상도 및 적층성을 향상시켰으며 잉크젯 프린팅을 이용한 광경화 나노 실리카 잉크의 3D 프린팅에 대한 가능성을 확인하였다.

• 한국재료학회지
• /
• 제20권9호
• /
• pp.483-487
• /
• 2010

To fabricate $TiO_2$ nanoparticle-based dye sensitized solar cells (DSSCs) at a low-temperature, DSSCs were fabricated using hydropolymer and ZnO nanoparticles composites for the electron transport layer around a low-temperature ($200^{\circ}C$). ZnO nanoparticle with 20 nm and 60 nm diameter were used and Pt was deposited as a counter electrode on ITO/glass using an RF magnetron sputtering. We investigate the effect of ZnO nanoparticle concentration in hydropolymer and ZnO nanoparticle solution on the photoconversion performance of the low temperature fabricated ($200^{\circ}C$) DSSCs. Using cis-bis(isothiocyanato)bis(2,20 bipyridy1-4,40 dicarboxylato) ruthenium (II) bis-tetrabutylammonium (N719) dye as a sensitizer, the corresponding device performance and photo-physical characteristics are investigated through conventional physical characterization techniques. The effect of thickness of the ZnO photoelectrode and the morphology of the ZnO nanoparticles with the variations of hydropolymer to ZnO ratio on the photoconversion performance are also investigated. The morphology of the ZnO layer after sintering was examined using a field emission scanning electron microscope (FE-SEM). 60 nm ZnO nanoparticle DSSCs showed an incident photon-to-current conversion efficiency (IPCE) value of about 7% higher than that of 20 nm ZnO nanoparticle DSSCs. The maximum parameters of the short circuit current density ($J_{sc}$), the open circuit potential ($V_{oc}$), fill factor (ff), and efficiency ($\eta$) in the 60 nm ZnO nanoparticle-based DSSC devices were 4.93 mA/$cm^2$, 0.56V, 0.40, and 1.12%, respectively.

• 한국분말재료학회지
• /
• 제24권6호
• /
• pp.477-482
• /
• 2017

Nitrogen-doped titanium dioxide (N-doped $TiO_2$) is attracting continuously increasing attention as a material for environmental photocatalysis. The N-atoms can occupy both interstitial and substitutional positions in the solid, with some evidence of a preference for interstitial sites. In this study, N-doped $TiO_2$ is prepared by the sol-gel method using $NH_4OH$ and $NH_4Cl$ as N ion doping agents, and the physical and photocatalytic properties with changes in the synthesis temperature and amount of agent are analyzed. The photocatalytic activities of the N-doped $TiO_2$ samples are evaluated based on the decomposition of methylene blue (MB) under visible-light irradiation. The addition of 5 wt% $NH_4Cl$ produces the best physical properties. As per the UV-vis analysis results, the N-doped $TiO_2$ exhibits a higher visible-light activity than the undoped $TiO_2$. The wavelength of the N-doped $TiO_2$ shifts to the visible-light region up to 412 nm. In addition, this sample shows MB removal of approximately 81%, with the whiteness increasing to +97 when the synthesis temperature is $600^{\circ}C$. The coloration and phase structure of the N-doped $TiO_2$ are characterized in detail using UV-vis, CIE Lab color parameter measurements, and powder X-ray diffraction (XRD).

• 한국수소및신에너지학회논문집
• /
• 제13권3호
• /
• pp.224-232
• /
• 2002

CdS-$TiO_2$ nano-composite sol was prepared by the sol-gel method in organic solvents at room temperature and further hydrothermal treatment at various temperatures to control the physical properties of the primary particles. Again, CdS-$TiO_2$ composite particulate films were made by casting CdS-$TiO_2$ sols onto $F:SnO_2$ conducting glass and then heat-treatment at $400^{\circ}C$. Physical properties of these 61ms were further controlled by the surface treatment with $TiCl_4$, aqueous solution. The photo currents and hydrogen production rates measured under the experimental conditions varied according to the $CdS/[CdS+TiO_2]$ mole ratio and the mixed-sol preparation method. For $CdS-TiO_2$ composite sols prepared in IPA, CdS particles were homogeneously surrounded by $TiO_2$ particles. Also, the surface treatment with $TiCl_4$ aqueous solution caused a considerable improvement in the photocatalytic activity, probably as a result of close contacts between the primary particles by the etching effect of $TiCl_4$. It was found that the photoelectrochemical performance of these particulate films could be effectively enhanced by this approach.

• 한국전산유체공학회지
• /
• 제13권4호
• /
• pp.66-71
• /
• 2008

This research computes the viscous flow field and aerodynamics around the model of a commercial passenger airplane, Boeing 747-400, which cruises in transonic speed. The configuration was realized through the reverse engineering based on the photo scanning measurement. In results, the pressure coefficients at the several wing section on the wing surface of the airplane was described and discussed to obtain the physical meaning. The lift coefficient increased almost linearly up to $17^{\circ}$. Here the maximum lift occurred at $18^{\circ}$ according to the angle of attack. And the minimum drag is expected at $-2^{\circ}$. The maximum lift coefficient occurred at the Mach number 0.89, and the drag coefficient rapidly increased after the Mach number of 0.92. Also shear-stress transport model predicts slightly lower aerodynamic coefficients than other models and Chen's model shows the highest aerodynamic values. The aerodynamic performance of the airplane elements was presented.

• 천문학논총
• /
• 제27권4호
• /
• pp.261-262
• /
• 2012

The aim of this research is to reveal the spatial distribution of the star formation activity of nearby galaxies by comparing CO molecular emission lines with the large area observation in far-infrared (FIR) lines. We report the imaging observations of NGC 253 by FIR forbidden lines via FIS-FTS and CO molecular lines from low to high excitation levels with ASTE, which are good tracers of star forming regions or photo-dissociation regions, especially spiral galaxies, in order to derive the information of the physical conditions of the ambient interstellar radiation fields. The combination of spatially resolved FIR and sub-mm data leads to the star formation efficiency within galaxy. The ratio between the FIR luminosity and molecular gas mass, $L_{FIR}/M_{H_2}$, is expected to be proportional to the number of stars formed in the galaxy per unit molecular gas mass and time. Moreover the FIR line ux shows current star formation activity directly. Furthermore these can be systematic and statistical data for star formation history and evolution of spiral galaxies.

• Toxicological Research
• /
• 제34권1호
• /
• pp.31-39
• /
• 2018

The objective of this study was to evaluate the antioxidant and anti-aging effects of marigold methanol extract (MGME) in human dermal fibroblasts. Total polyphenolic and flavonoid contents in MGME were 74.8 mg TAE (tannic acid equivalent)/g and 85.6 mg RE (rutin equivalent)/g, respectively. MGME ($500{\mu}g/mL$) increased 1,1-diphenyl-2-picryl hydrazyl (DPPH) and 2,2'-azino-3-ethylbenzothiazoline-6-sulfonic acid (ABTS) radical-scavenging, and superoxide dismutase (SOD)-like antioxidant activities by 36.5, 54.7, and 14.8%, respectively, compared with the control. At $1,000{\mu}g/mL$, these activities increased by 63.7, 70.6, and 20.6%, respectively. MGME ($100{\mu}g/mL$) significantly increased the synthesis of type 1 procollagen by 83.7% compared with control treatment. It also significantly decreased Matrix Metalloproteinase-2 (MMP-2) activity and MMP-1 mRNA expression by 36.5% and 69.5%, respectively; however, it significantly increased laminin-5 mRNA expression by 181.2%. These findings suggest that MGME could protect human skin against photo-aging by attenuating oxidative damage, suppressing MMP expression and/or activity as well as by stimulating collagen synthesis.

• 폴리머
• /
• 제25권5호
• /
• pp.625-634
• /
• 2001

액상 이소프렌 고무에 무수 말레간(MAH)을 그라프팅시킨 후 2,2,6,6-tetramethyl-4-piperidinol (TMPO)를 반응시켜 hindered amine light stabilizer (HALS)가 함유된 새로운 고분자형 광안정제를 합성하고, SBR에 대한 광안정제로서의 특성을 관찰하였다. 새로운 고분자형 광안정제의 조성과 물리적 성질은 적정법, GPC 그리고 열중량 분석에 의하여 분석하였다. SBR의 광산화 반응에 대한 고분자형 광안정제의 효과를 254nm 자외선 조사에 따른 자외선 흡광도의 변화, 관능기 변화 그리고 잔막율로서 관찰한 결과, 새로운 고분자형 광안정제를 첨가함으로써 광산화 반응이 효과적으로 억제되었다. 또한, 고부자형 광안정제의 추출내성은 저분자량의 모델 화합물에 비하여 훨씬 우수하였으며, 고분자형 광안정제와 SBR의 상용성은 TMPO가 SBR 필름 표면에 균일하게 고루 분산되어 있어서 매우 우수하였다.

• 한국인쇄학회지
• /
• 제28권1호
• /
• pp.51-63
• /
• 2010

Ink-jet is part of the non impact printing that shooting the ink drop from the nozzle to paper. It is very silence and express good color. There are two types of printing that continuous and drop on demand. But drop on demand process is becoming the mainstream. these days, LCD, PDP is passed more than semiconductor industry. And we expect organic EL, FED as a next display. But product equipment, main component and technology have a gap between an advanced country and us nevertheless physical development. Expecially, previous process part is depended on imports. Ink-jet printing technology that there isn't complicated photo lithography process is attracted, so ink-jet printing resolution is more embossed. But there were not many of ink-jet resolution thesis but ink-jet head or nozzle. Because, to out of the ink from the nozzle is unseeable and hard to experiment. Therefore this thesis was experimented and simulated how can ink-jet printer improved resolution by flow-3d simulation package program.