• 한국대기환경학회지
• /
• 제9권3호
• /
• pp.247-254
• /
• 1993

A simple and direct method is developed for the determination of light Elements in atmospheric particulates by X-ray fluorescence spectrometry. Calibration standards for the light elements such as Al, Mg, K, Ca, etc are prepared by filtering real atmospheric particulates over variable time and subsequently standardizing them by Inductively Coupled Plasma-Mass Spectrometry(ICP-MS) or Atomic Absorption Spectrophotometry(AAS) analysis. The validity of this calibration method is tested by analyzing more than 100 aerosol samples, collected at urban(Seoul) and rural(Padori) sites over a two year period with this method and then comparing them with those by other accuracy proven methods such as AAS or ICP-MS: for all metals tested the results showed reasonably good agreements (R $\geq$ 0.95).

• 한국대기환경학회지
• /
• 제7권2호
• /
• pp.89-95
• /
• 1991

Yellow sands often occur in Korea during April and May each year, and they are believed to come from the Mongolian Gobi desert as the snow starts to melt in Spring time. Since the analysis of aerosol particulates can hardly distinguish the origin of particulates, the isentropic analysis of meteorological data is often used for the trajectories of the long range transport of yellows sand or air pollutants. The yellow sand case of April 9 $\sim$ 15, 1988, in Korea is analyzed for the identification of long range transport of yellow sands and their trajectories in East Asia, using isentropic analyses. We have tranformed the ECMWF grid data, analyzed in pressure coordinates, into the isentropic coordinates and then have traced the 286 K and 290 K air mass which started Gobi desert. The result shows the transport of yellow sands from the Gobi desert to the Korean peninsula.

• 약학회지
• /
• 제33권1호
• /
• pp.46-53
• /
• 1989

The extractable organic matter was extraced from airborne particulates collected in Seoul during 1986. It was fractionated to several fracrtions and mutagenicities of them were tested in Salmonella thyphimurium TA98 by Ames method. The neutral fraction showed the highest indirect acting mutagenicity while the highest direct acting mutagenicity was observed in the acidic fraction. Indirect acting mutagenicity of airborne particulate was attributed to its neutral fraction about 88% in average, to acidic about 10% in average and to basic fraction about 2% in average. Direct acting mutagenicity of airborne particulate was attributed to its neutral fraction about 70%, to acidic fraction about 29% and to basic fraction about 1%. Among five subfractions of neutral fraction, the proportion of mutagenicity of polynuclear aromatic hydrocarbon subfraction was 13.2% in indirect acting mutagenicity and 5.0% in direct acting mutagenicity.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1984년도 하계학술회의논문집
• /
• pp.226-229
• /
• 1984

A novel high intensity charging device has been developed for the control of the submicron particles, such as the diesel soot particulates, which are very hard to charge highly by any means of the conventional charging device. Having new corona electrodes of a multineedle disk with the corona field-control electrodes in the outer-cylinder electrode, extremely intense and stable coronas on there sharp points expanding both radially and axially are established in the corona charging region between the multi-corona -needles and an outer-cylinder electrode. As a result, the maximum corona field intensity and current density of the charging device of the standard one on soot load in laboratory tests have been 8.5KV/cm(E=$2V_m$/D(1nD/d)) and $6.5{\mu}A/cm^2$ which enhance greatly the charging of soot particles about several 100 times higher than those obtained in conventional cylinder precipitators.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.78-86
• /
• 1995

The silicon nitride based ceramic cutting tool materials have been fabricated by gas pressure sintering (GPS) or hot pressing (HP). Their mechanical properties were measured and the effect of the fabrication variables on the properties were examined. Also, effect of adding TiN or TiC particulates on the mechanical properties of the silicon nitride ceramics were investigated. Ceramic cutting tools (ISO 120408) were made of the sintered bodies. Cutting performance test were performed on either conventional or NC lathe. The workpieces were grey cast iron, hardened alloy steel (AISI 4140, HRc>60) and Ni-based superalloy (Inconel 718). The results showed that fabrication variables, namely, sintering temperature and time, exerted a strong influence on the microstincture and mechanical properties of the sintered body, which, however, did not make much difference in wear resistance of the tools. High hardness of the tool containing TiC particulates exhibited good cutting performance. Extensive crater wear was observed on both monolithic and TiN-containing silicon nitride tools after cutting the hardened alloy steel. Inconel 718 was extremely difficult to cut by the current cutting tools.

• 수산해양기술연구
• /
• 제30권3호
• /
• pp.220-226
• /
• 1994

In this paper the failure mechanisms of polypropylene resin composites filled with calcium carbonate particulates have been studied in the temperature range $-50^{\circ}C$ to $-50^{\circ}C$ The fillers used are both untreated and surface treated with stearic acid. The impact fracture toughness is evaluated from the impact energy absorbed divided by the uncut ligament area of the specimen. Impact fracture toughness increases as temperature is raised whether the fillers are coated or not. The static fracture toughness of these particular composites is evaluated based on the linear clastic fracture toughness of these particular composites is evaluated based on the linear clastic fracture mechanics. Static fracture toughess decreases with increasing temperature whether the fillers are coated or not. An extended stress whitened zone are observed through a large number of availabel sites for cavitation/debonding along particle matrix interface and matrix deformation.

• 한국대기환경학회지
• /
• 제8권2호
• /
• pp.112-120
• /
• 1992

Twenty four metal, nonmetal elements and 4 major anions in total suspended particulates (TSP) collected at two sites in Daejon city from october to december in 1991 by a Hi-vol sampler were thoroughly analyzed by Inductively Coupled Plasma/ Atomic Emission Spectrometry (ICP/AES) and Ion Chromatography (IC). These analyzed data were used to perform a receptor modeling using the Chemical Mass Balance (CMB) for the source apportionment of TSP sample. Approximately 60% TSP weight in industrial complex area was influenced by potential industrial sources and 25% was by heating fuels and automobile emissions, whereas a half of TSP in residential area was influenced by surrounding environment and more than 35% of TSP was influenced by heating fuels. The CMB model provided source apportionment results reasonably and scientifically with a minor limitation.

• 한국레이저가공학회지
• /
• 제3권3호
• /
• pp.39-45
• /
• 2000

The volume and depth of the craters produced on silicon samples during high power laser ablation show a strong nonlinear change as the laser irradiance increases across a threshold value, approximately 2.2$\times$10$\^$10/ W/㎠. Time-resolved shadowgraph images of the ablation plume reveal the ejection of large particulates from the sample for laser irradiance above the threshold, with a time delay of about 300-400 ㎱. The numerically estimated thickness of the superheated liquid layer, considering the transformation of liquid metal into liquid dielectric near the critical state, agrees with the measured agrees with crater depths. It is suggested that a phase explosion of the deep superheated liquid layer near the critical state is responsible for the measured sudden increase of crater volume and the ejection of large particulates.

• 한국세라믹학회지
• /
• 제31권3호
• /
• pp.312-320
• /
• 1994

Effect of the laser shot number on the particulates density of the pulsed laser deposited YBa2Cu3O7-x thin films and the laser irradiated surface morphology of the YBa2Cu3O7-x bulk target have been investigated. Until 100 laser shots of cumulative irradiation, the films has the particulates density of ~103 mm-2. However, after 100 laser shots, the density was increased more than 10 times. This results has been explained by the change of particulate ejection path with the development of conical structure at the target surface.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2297-2299
• /
• 2005

In this paper, a finite element (FEM) investigation of composite materials is studied. A pemittivity profile of the material is implemented to correspond to the Packing fraction of the physical composite. Curve fitting is applied to the standing wave pattern to determine the effective attenuation coefficient and propagation constant in the composite. The complex permittivity as a function of packing density is then determined. A comparison between the two dimensional and three dimensional measurement simulations is presented. An adaptive scheme is implemented to improve resolution of the finite element particulates.