• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.57-58
• /
• 2005

The properties such as capacitance and resonant frequency are important in embedded capacitors. Accurate equivalent model is required to find these properties of embedded capacitor. In this paper, we investigate to analyze the properties of high-K embedded capacitor which was fabricated by Low Temperature Co-fired Ceramic (LTCC). Modeling based on partial element equivalent circuit (PEEC) method is performed using HSPICE circuit simulation. This modeling methodology can provide the good inspection of embedded capacitor to device engineer.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.5
• /
• pp.410-418
• /
• 2009

Based on a linear potential theory, the boundary element method(BEM) is developed and applied to analyze the hydrodynamic forces and the motion responses of a floating body with a partially reflective sidewall. The hydrodynamic forces (added mass and damping coefficients) are dependent on not only the submergence of a floating body and the reflection of a sidewall, but also the gap between body and sidewall. In particular, the partial reflection of a sidewall plays an importance role in the motion responses of a floating body at resonant frequencies. It reduces the resonant peaks caused by resonance phenomenon due to the wave trapping in an enclosed fluid domain between body and sidewall. Developed predictive tools can be used to assess the motion performance of a floating body for various combinations of configuration of a floating body, wave heading, sidewall properties, and wave characteristics and applied to supply the basic informations for the harbour design considering the motion characteristics of a moored ship.

• Journal of IKEEE
• /
• v.13 no.2
• /
• pp.194-199
• /
• 2009

In this study, ultra high-voltage (170kV AC), reliable 80pF mica capacitors for partial discharge system application were investigated. For capacitors design, Program was developed to sampling of series and parallel parameters. Mica was used as the dielectric of the capacitors. Using the conservative design rule, over 3 individual 50$\mu$m thick mica sheets with a size of 30mm$\times$35mm were used with lead foils to form a parallel capacitor element and 20 mica sheets were interleaved with lead foils to form a series stack of parallel capacitor element to meet the requirements of the capacitors. The dimension of the fabricated 80pF capacitor for 17kV AC were 90mm$\times$90mm. The high-frequency characteristics of the capacitance (C) and dissipation factor (D) of the developed capacitors were measured using a capacitance meter. The developed capacitor exhibited C of 79.5pF, had D of 0.001% over the frequency ranges of 150kHz to 50MHz, had a self-resonant frequency of 65MHz.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.6
• /
• pp.465-471
• /
• 2007

The system efficiency of the proposed Buck-Boost AC-DC converter is increased by soft switching method. The converter includes to merit of power factor correction (PFC) from sinusoidal control of input current. The switching behavior of control switches operates with soft switching by partial resonance, and then the proposed converter has high system efficiency with decrement of switching power loss. The input current waveform in proposed converter is got to be a sinusoidal form of discontinuous quasi-pulse row in proportion to magnitude of AC input voltage under the constant duty cycle switching. Therefore, the input power factor is nearly unity. The output voltage of the converter is regulated by PWM control technique. The discontinuous mode action of current flowing into inductor makes to simplify control method and control components. The proposed PFC Buck-Boost converter is analyzed to compare with the conventional PFC Buck-Boost converter. Some computer simulative results and experimental results confirm to the validity of the analytical results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.5
• /
• pp.394-399
• /
• 2007

In this paper, we study on a novel Buck-Boost converter of high efficiency by soft switching method. The proposed Buck-Boost converter is applied to new soft switching method in restraint of increment of switching power loss in the conventional Buck-Boost converter. The soft switching circuit is designed to modification of a energy storage inductor and a snubber circuit used by the conventional converter, and then the proposed converter is simplified. The controlling switches of the proposed converter is operated with soft switching by a partial resonance behavior. The output voltage of the converter is regulated by PWM control technique. The discontinuous mode action of current flowing into inductor makes to simplify control method and control components. The proposed Buck-Boost converter is compared with the conventional converter. Some computer simulative results and experimental results are confirmed to the validity of the analytical results.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.4
• /
• pp.9-15
• /
• 2006

This paper shows the impedance profile of PEEC(Partial Equivalent Electrical Circuit) PDN(Power Distribution Networks) including core and I/O circuit. Through the simulated results, we find that the core power noise having connection with I/O power is affected by I/O switching. Also, using designed $74{\times}5inch$ DLL(Delay Locked Loop) test board, we analyzed the effect of power noise on operation region of chip. Jitter of a DLL measure for frequency of $50{\sim}400MHz$ and compared with impedance obtained result of simulation. Jitter of a DLL are increased near about frequency of 100MHz. It is reason that the resonant peak of PDNs has an impedance of more the 1ohm on 100MHz. we present the impedance profile of a chip and board for the decoupling capacitor reduced the target impedance. Therefore, power supply network design should be considered not only decoupling capacitors but also core switching current and I/O switching current.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.3
• /
• pp.217-224
• /
• 2018

In this study, the optimal design methods of soft-switching cell for high-voltage DC-DC converter (HDC) of fuel cell electric vehicles (FCEVs) is proposed for high efficiency and high power density. The appropriate soft-switching cell for FCEVs is chosen by analyzing the losses of HDC which adopts soft-switching cell. The proposed optimal design methods for the soft-switching cell are divided into two purposes which are improvement of efficiency and power density. Two kinds of design methods enable to improve fuel efficiency and cost, respectively. The proposed design methods are validated with the experimental results based on the specification and hardware used in actual FCEVs.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.178-183
• /
• 2020

A series of experiments covering lowest three natural frequencies of rolling coupled pitching were conducted to investigate liquid sloshing with low liquid depth. The test results show that the most violent liquid sloshing in rolling and pitching is located in the vicinity of the first order natural frequency (f1). When the excitation frequency of rolling and pitching is located between 0.98f1 and 1.113f1, roof-bursting phenomenon of liquid appeared, and the maximum impact pressure is at 1.09f1. When the external excitation frequency is at 1.113f1, the number of sloshing shocks decreases sharply. Furthermore, the space distribution of the impact pressure on the left bulkhead and the top bulkhead was analyzed. It is concluded that with low liquid filling, the impact load is greater near the free surface and the top of tank, and the impact position of the side bulkhead increases with the increasing of the frequency near the resonant frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.283-291
• /
• 2012

In this paper, a compact antenna is designed for the UWB lower half-band WVAN Gbps data-rate transceiver. The proposed antenna broadens the bandwidth less than -10 dB by placing the ring stubs and an open stub on the rectangular monopole above the partial ground and creating multiple resonant current paths. The designed antenna goes through the electromagnetic simulation and is fabricated and the implemented antenna has the characteristics of the return loss lower than -10 dB, the antenna gain greater than 5 dBi, and the efficiency over 80 % in the UWB lower half-band ranging from 3.197 GHz to 4.732 GHz. Therefore, it is thought that the proposed antenna is suitable for the size-reduced and excellently performing wireless communication transceiver.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.2
• /
• pp.154-160
• /
• 2009

This paper describes a wide bandwidth RFID tag antenna design for protection of connection part between chip and antenna. A proposed tag antenna size, a resonant frequency and bandwidth are $53{\times}10{\times}1\;mm$, 900 MHz and 800 MHz($500{\sim}1,300\;MHz$) at -10 dB below, respectively. The dielectric materials with different relative permittivity such as polyethylene, glass and silicon were applied for protection of connection part between the proposed antenna and chip on the way of whole and partial housing. The measured return loss and radiation pattern agreed well with the calculation results. The read range of the proposed tag antenna without any housing and of tag antenna with housing covered over all by silicon with 3 mm thickness were observed about 5 m and 4 m, respectively.