• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.1
• /
• pp.104-111
• /
• 2009

This paper shows the behaviors of macro- and micro-structures and mechanical properties for specimen's welding region welded by FSW. according to welding conditions with 5mm thickness aluminum 5083O alloy plate. It apparently results in defect-free weld zone in case traverse speed was changed to 32 mm/min under conditions of anti-clockwise direction and tool rotation speed such as 800 and 1250 rpm with tool's pin diameter of 5 ${\Phi}mm$ and shoulder diameter of 20 ${\Phi}mm$, pin length of 4.5 mm and tilting angle of $2^{\circ}$. The ultimate stress of ${\sigma}_T=331$ MPa and the yield point of 147 MPa are obtained at the condition of the travel speed of 32 mm/min with the tool rotation speed of 1250 rpm. There is neither voids nor cracks on bended surface of $180^{\circ}$ after bending test. The improvement of toughness after impact test was found. The lower rotating and traverse speed became, the higher were yield point, maximum stress and elongation(%) with the stresses and the elongation(%) versus the traverse speed diagram. Vickers hardness for cross section of welding zone were also presented. The typical macro-structures such as dynamically recrystallized zone, thermo-mechanically affected zone and heat affected zone and the micro-structures of the transverse cross-section were also showed. However, the author found out that the region of 6mm far away from shoulder circumference was affected by friction heat comprehensively, that is, hardness softened and that part of micro-structures were re-solid-solution or recrystallized, the author also knew that there is no mechanically deformation on heat affected zone but there are the flow of plastic deformation of $45^{\circ}$ direction on thermo-mechanically affected zone and the segregation of Al-Mg on nugget. The solid solution wt(%) of parent material as compared against of friction stir welded zone was comprehensively changed.

• Korean Journal of Medicinal Crop Science
• /
• v.14 no.2
• /
• pp.107-112
• /
• 2006

Two Atractylodes species, A. japonica Koidz. ex Kitam. (AJ) and A. macrocephala Koidz (AM) were used in this study. AJ population had higher amounts of Sesquiterpenoids and stronger tolerance to root rot but less vigor of root growth than AM population. Two populations (AJ and AM) were crossed to make interspecific hybrid population. A total of 98 lines propagated clonally were selected from a cross of AJ and AM, and evaluated for contents of sesquiterpenoids, atractylon (ATLN) and atractylenolide III (AT3) using high performance liquid chromatography (HPLC), and growth characters such as plant height, stem number and root weight. HPLC profiles of the hybrids were compared with those of parent plants, and it demonstrated the production of introgression hybrid by crossing between AJ and AM. Of 98 clonal lines,10 lines were selected by 10% level based on the growth vigor and tolerance to root rot, and AJM2102-51 line showed the heaviest root weight (117.1 g/plant) among them. A total of 98 hybrid lines contained on average $0.16\;{\pm}\;0.10\;mg/g$ of $AT3,\;2.00\;{\pm}\;1.37\;mg/g$ of ATLN, and $2.16\;{\pm}\;1.40\;mg/g$ of total sesquiterpenoids, showing high coefficients of variation (above 65%). Ten lines having high contents of sesquiterpenoids were selected, and AJM2101-15 had the highest amount (9.83 mg/g) of ATLN, and showed 40.8 g/plant of root weight similar to mean value (39.9 g/plant) of hybrid lines. The result showed that the introgression of both characters of vigorous growth from AM and high sesquiterpenoids content from AJ could be possible to make new hybrid lines by crossing between AJ and AM.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.50 no.4
• /
• pp.281-285
• /
• 2005

Pod dehiscence (PD), defined as the opening of pods along both the dorsal and ventral sutures, causes the seed to shatter in the field before harvesting and results in loss of seed yields. However, breeding for resistance to PD is difficult due to the complicated genetic behavior and environmental interaction. The objective of the present research was to analyze the genetic behavior of PD for improving the breeding efficiency of resistance to PD in soybean. PD after oven-drying the sampled pod at $40^{\circ}C$ for 24 hours was the most reliable to predict the degree of PD tested in the field. Keunolkong, a dehiscent parent, was crossed with non-dehiscent parents, Sinpaldalkong and Iksan 10. Using their $F_1\;and\;F_2$ seeds, PD was measured after oven drying the pod at $40^{\circ}C$ for 24 hours. The gene conferring PD behaved in different manners depending on the genetic populations. In the Keunolkong$\times$Sinpaldalkong population, PD seemed to be governed by single major recessive gene and minor genes, while several genes were probably involved in the resistance to pod dehiscence in the Keunolkong$\times$Iksan 10 population. Heritability for PD estimated in F2 population showed over $90\%$ in the two populations. High heritability of PD indicated that selection for resistance to PD should be effective in a breeding program. In addition, genetic mapping of quantitative locus (QTL) for PD in both populations may reveal that genes conferring PD are population-specific.

• Journal of the Korean Professional Engineers Association
• /
• v.25 no.4
• /
• pp.102-108
• /
• 1992

This study was carried to find out the soil characteristics of landslide site and to develope landslide prediction method by seismic refraction prospecting. For these aims, landslide condition and travel time were investigated at 68 Landslide sites over the country during 1990 to 1991. The results were as follows. 1. The surface of rupture was included mainly in C layer. Its Hardness was less than 3kg / $\textrm{cm}^2$ at the upper pare of landslide. 2. When the profile line length was 20m, the range of travel time was 40 to 90 msec. The travel time did not differ between bedrocks. 3. Refraction distance ranged from 1 to 7m and mean of that was 2.5m. Travel time was increased according to receiving distance without large variance in the refraction distance but that was appeared large variance out of the refraction distance on slope that has shallow soil depth and discontinuous ground surface. Therefore, the spread distance must be shorten to 10-l5m. 4. The seismic velocity at the first layer(layer of rupture) was less than 500m1sec by degree of weathering and the velocity at the second layer decreased in order of Granite> Granitic gneiss >Sedimentary rock. 5. The first layer observed by seismic refraction was contained C layer that has parent material and weathered rocks of hardness 10-20kg/$\textrm{cm}^2$. 6. Among the range of seismic velocity was less than 200m/sec in 63% of the total plots, 200-300m/sec in 34% and 300-500m /sec in 3%. 7. There was a proportional relationship between seismic prospecting soil depth and executive soil depth, and seismic propection soil depth was about 10 to 20cm deeper than the order.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.12
• /
• pp.1327-1331
• /
• 2005

This study was to investigate the reduction of hydration heat by utilizing industrial by-products such as BFS(Blast Furnace Slag). DM(Dredged Mud) was used by parent soil and Ordinary portland cement was used by cementing material. Additive added to reduce the heat of hydration was BFS. From the results of experiment, hydration heat was decreased in accordance with the addition of BFS. The reason was that surface of BFS coated with aluminosulfate. Initial uniaxial strength was low, neither was not long term uniaxial strength. It was concluded that silica rich layer($H_2SiO_4^{4-}$) in solid phase early in the reaction of hydration was difficultly moved in liquid phase due to the increase of ZP(Zeta Potential). However, the ZP in the later hydration was decreased due to the acceleration of mobility of silica rich layer($H_2SiO_4^{4-}$). Therefore, long term physical properties such as uniaxial strength revealed.

• Journal of the korean society of oceanography
• /
• v.35 no.1
• /
• pp.16-33
• /
• 2000

In order to measure the vertical fluxes of particles and reactive radionuclides such as thorium and polonium isotopes, Dunbar-type sediment traps were freely deployed at the Ulleung Basin and in warm and cold water masses around the polar front of the East Sea. We estimated the ratios of the catched (F) to the predicted $^234$Th fluxes (P) using natural tracers pair $^234$Th-$^238$U. The F/P ratios are decreased with increasing water depth. Whereas the concentrations of suspended particles are homogeneous in water column, the mass fluxes are also decreased with increasing water depth like the F/P ratios. These facts indicate that organic matters of settling particles are destructed within the euphotic layer due to decomposition. Whereas regenerations of sinking particles are negligible in the cold water mass, about 80% of them are regenerated in the warm water mass during falling of large particles. These downward mass fluxes are closely correlated with their primary productions in euphotic zone. The activities of $^234$Th, $^228$Th and $^210$Po in the sinking material were increased with water depth. Because $^234$Th steadily produced in the water column are cumulatively adsorbed on the surface of sinking particles, vertical $^234$Th fluxes were observed to increase with water depth. Therefore, these sinking particles play important roles in transporting the particle reactive elements like thorium from surface to the deep sea. The scavenging processes including adsorption and settling reactions generate radio-disequilibrium between daughter and parent nuclides in water column. The activity ratios of $^234$Th/$^238$U and $^228$Th/$^228$Ra were observed to be < 1.0 in the surface water and approached to be equilibrium below the thermocline. The extent of the deficiency of daughter nuclides compared to the parents nuclide was highly correlated with the vertical particle flux. Because most of the $^210$Po in the surface water are scavenged on a labile phase and are recycled at sub-surface depths (< 200 m), the $^210$Po are always observed to be excess activities compared to $^226$Ra in surface water.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.3
• /
• pp.121-126
• /
• 2006

HVOF thermal spray coating of Co-alloy T800 is progressively replacing the classical hard coatings such as chrome plating because of the very toxic $Cr^{6+}$ ion known as carcinogen causing lung cancer. For the study of the possibility of replacing of chrome plating, the wear properties of HVOF Co-alloy T800 coatings are investigated using the reciprocating sliding tester both at room and at an elevated temperature of $1000^{\circ}F\;(538^{\circ}C)$. The possibility as durability improvement coating is studied for the application to the high speed spindles vulnerable to frictional heat and wear. Wear mechanisms at the reciprocating sliding wear test are studied for the application to the systems similar to the sliding test such as high speed spindles. Wear debris and frictional coefficients of T800 coatings both at room and at an elevated temperature of $1000^{\circ}F\;(538^{\circ}C)$ are drastically reduced compared to those of non-coated surface of parent substrate Inconel 718. This study shows that the coating is recommendable for the durability improvement coatings on the surfaces vulnerable to frictional heat. The sliding surfaces are weared by the mixed mechanisms such as oxidative wear, abrasion by the sliding ball slurry erosion by the mixture of solid particles and small drops of the melts and semi-melts of the attrited particles cavitation by the relative motions among the coating, sliding ball, the melts and semi-melts. and corrosive wear. The oxide particles and the melts and semi-melts play roles as solid and liquid lubricant reducing the wear and friction coefficient.

• Journal of Technologic Dentistry
• /
• v.25 no.1
• /
• pp.9-20
• /
• 2003

Using a nickel-chrome casting alloy called 'Rexillium V' which is also available as base metal alloy for dental ceramic crown, 4 types of mixtures(A, B, C, D) with old and new metal were prepared for cyclic casting. The results of cyclic casting can be outlined as follows: 1. For Vickers hardness after casting, specimen A and D tended to have lower hardness in the course of cyclic casting, while specimen B and C tended to higher hardness. 2. The results of X-ray diffraction analysis showed that major crystal phase contained nickelchrome compounds and carbide. 3. The observation results of SEM photographs after cyclic casting show that there was a significant tendency to have similar structures among experimental groups. 4. The results of EDX analysis after cyclic casting showed that there were little differences in chemical composition between parent metal and base metal alloy. Although industrial nickel-chrome cast alloy did not show any significant change in material properties even through cyclic casting over several times, it is recommended that more there be more in-depth studies on how to detect any potential corrosion, discoloration and toxication of dental ceramic crown implanted in patient's oral cavity.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.6
• /
• pp.32-37
• /
• 2006

Micron size Co-alloy(T800) powder was coated on Inconel 718 by HVOF thermal spraying for the studies of the improvement of durability of high speed spindle by using Taguchi program for the parameters of spray distance, flow rates of hydrogen and oxygen and powder feed rate. The optimal coating process was determined by the studies of coating properties such as micro-structure, porosity, surface roughness and micro hardness. Friction and wear behaviors of coatings were investigated by sliding wear test at room temperature and $1000^{\circ}F(538^{\circ}C)$. At both room temperature and $538^{\circ}C$ the sliding wear debris and friction coefficients of the coating were drastically reduced compared with the surface of non-coated parent material. This shows that Co-alloy powder coating is highly recommendable for the durability improvement surface coating of high speed air-bearing spindle. At high temperature wear traces and friction coefficients of both coating and non-coating were drastically reduced compared with those of room temperature since the brittle oxides were formed easily on the surface, and the brittle oxide phases were attrited by the reciprocating sliding wear according to the complicated mixed wear mechanisms These oxide particles, partially melts and the melts play role as lubricant and reduce the wear and friction coefficient. This also shows that Co-alloy powder coating is highly recommendable far the durability improvement surface coating on the surface vulnerable to frictional heat such as high speed spindles.

• Spatial Information Research
• /
• v.20 no.3
• /
• pp.57-66
• /
• 2012

Gangwon-do has been suffering extensive landslide dam age, because its geography consists mainly of mountains. Analyzing the related factors is crucial for landslide prediction. We digitized the landslide and non-landslide spots on an aerial photo obtained right after a disaster in Inje, Gangwon-do. Three landslide factors-topographic, forest type, and soil factors-w ere statistically analyzed through GIS overlap analysis between topographic map, forest type map, and soil map. The analysis showed that landslides occurred mainly between the inclination of $20^{\circ}$ and $35^{\circ}$, and needleleaf tree area is more vulnerable to a landslide. About soil properties, an area with shallow effective soil depth and parent material of acidic rock has a greater chance of landslide.