• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2003.06a
• /
• pp.256-261
• /
• 2003

A memory industry is developing rapidly according to the period of the ubiquitous to approach. According to the development of a memory industry, the efficiency of the manufacture is becoming the serious consideration. DC parameter test system was a development low in this research for an efficiency increase of the manufacture. DC parameter test system increase of the manufacture. In the method to measure the output after permit volt and current at element.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.1
• /
• pp.7-14
• /
• 2002

In power system study, relibility assessment has been an important topic during past several decards because sudden power interruption can bring about enormous economic loss. although the size of a substation is smaller than that of generation system or transmission system, switching actions after fault(s) make reliability assessment of substation rather complex situations such as switching actions easily and permit various probability distributions in describing substation elements. Despite this ability of Monte Carlo simulation, one-parameter exponential distribution is still popular in this reliability assessment. This paper examines the characteristics of several two-parameter probability distributions, and offers new parameter decision rule based on average and variance of the target to be modelled. In case study, this paper shows the profits by using Weibull distribution which is one of two-parameter probabilistic distributions instead of exponential one.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.57.1-57.1
• /
• 2013

We investigate the method to measure both the present value of the matter energy density contrast and the Hubble parameter directly from the measurement of the linear growth rate which is obtained from the large scale structure of the Universe. From this method, one can obtain the value of the nuisance cosmological parameter $\Omo$ (the present value of the matter energy density contrast) within 3% error if the growth rate measurement can be reached $z >3.5$. One can also investigate the evolution of the Hubble parameter without any prior on the value of $H_0$ (the current value of the Hubble parameter). Especially, estimating the Hubble parameter are insensitive to the errors on the measurement of the normalized growth rate $f \sigma_8$. However, this method requires the high $z$ ($z >3.5$) measurement of the growth rate in order to get the less than 5% errors on the measurements of $H(z)$ at $z \leq 1.2$ with the redshift bin $\Delta z = 0.2$. Thus, this will be suitable for the next generation large scale structure galaxy surveys like WFMOS and LSST.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.672_673
• /
• 2009

In this paper seeks the parameter which relates with the efficiency from premium efficiency level single-phase induction motor. Also it compares with the parameters and it analyzes and an optimum parameter it seeks by FEM. Consquently, a optimal design is accomplished from the this paper. Also parameters compare efficiency. And it analyzes and studies about optimum parameter by FEM. The sample single-phase induction motor selection selected existing premium level motor. We analyze each parameter using 2-D finite element analysis (FEM). According to Study of losses and Design flow, losses and efficiency can be explain by many parameter. So this paper present optimal parameters. Finally, this paper presents the method which raises the efficiency of premium efficiency level single-phase induction motor.

• Industrial Engineering and Management Systems
• /
• v.6 no.2
• /
• pp.119-124
• /
• 2007

The most difficult and time-intensive issue in the successful implementation of genetic algorithms is to find good parameter setting, one of the most popular subjects of current research in genetic algorithms. In this study, we present a new efficient experimental design method for parameter optimization in a genetic algorithm for general job shop scheduling problem using the Taguchi method. Four genetic parameters including the population size, the crossover rate, the mutation rate, and the stopping condition are treated as design factors. For the performance characteristic, makespan is adopted. The number of jobs, the number of operations required to be processed in each job, and the number of machines are considered as noise factors in generating various job shop environments. A robust design experiment with inner and outer orthogonal arrays is conducted by computer simulation, and the optimal parameter setting is presented which consists of a combination of the level of each design factor. The validity of the optimal parameter setting is investigated by comparing its SN ratios with those obtained by an experiment with full factorial designs.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.7
• /
• pp.628-639
• /
• 1991

A new efficient method for GaAs MESFET model parameter extraction is proposed, which is based on the bias dependance of each parameter characteristics derved from the analytic model. The requiremnts of the method are only small-signal S-parameter measurements under the three bias variations. Fixation of the linear model parameter values in the optimization process is made using the sensitivity information of the model parameter obtained by the weighted Broyden update method, it is to improve the uniqueness and reliablility of the solution. The validity of the extracted values of the FET model parameters is confirmed by comparing the simulation results with the experimental data.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.2
• /
• pp.7-12
• /
• 2008

It is attempted, in this study, to analyze the movement of the fluidity of polar magnetic fluid and to relate Newtonian fluid with the Inlet Length of infinity plates when distance between parallel plates is L. A numerical analysis is performed for the variation of inlet length when magnetic effect parameter and polar effect parameter which give special advantages to magnetic fluid are increased. From the result of numerical analysis, we confirmed that the inlet length shortens as the flux around the center axis is accelerated and the flux around the surface of a wall is controlled as the magnetic effect parameter and the polar effect parameter are increased.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.2
• /
• pp.92-98
• /
• 2002

It is necessary to measure the solar cell parameter fur understanding characteristic of solar cell and applying to many other fields. Since photovoltaic system consists of solar cell module, which are connected each other in series and parallel, it is not proper to apply a solar cell parameter to photovoltaic system. Therefore, to estimate the solar tell module and to solve the problem of the established algorithm is on demand. In this paper the authors have improved the accuracy of solar cell module Parameter estimation by compensating series and Parallel resistance, and developed a new parameter estimation algorithm, which can be applied to photovoltaic system without high cost measuring equipment. And the validity of proposed algorithm is verified by the simulation and experimentation.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.8
• /
• pp.26-32
• /
• 1998

The grinding force generated during the grinding process causes an elastic deformation of the workpiece, grinding wheel, and machine system. Thus, the true depth of cut is always smaller than the apparent depth of cut. This is known as machining elasticity phenomenon. The machining elasticity parameter is defined as a ratio between the true depth of cut and the apparent depth of cut. It is an important factor to understand the material removal mechanism of the grinding process. To increase productivity, the value of this machining elasticity parameter must be large. Therefore, it is essential to know the characteristics of this parameter. The objective of this research is to study the effect of the major grinding conditions, such as table speed and depth of cut, on this parameter experimentally. Through this research, it is found that this parameter value is increasing when the table speed is decreasing or the depth of cut is increasing. Also, this parameter value depends on the grinding mode (up grinding, down grinding).

• Communications for Statistical Applications and Methods
• /
• v.24 no.6
• /
• pp.663-671
• /
• 2017

Some genetic association tests include an unidentifiable nuisance parameter under the null hypothesis of no association. When the mode of inheritance (MOI) is not specified in a case-control design, the Cochran-Armitage (CA) trend test contains an unidentifiable nuisance parameter. The transmission disequilibrium test (TDT) in a family-based association study that includes the unaffected also contains an unidentifiable nuisance parameter. The hypothesis tests that include an unidentifiable nuisance parameter are typically performed by taking a supremum of the CA tests or TDT over reasonable values of the parameter. The p-values of the supremum test statistics cannot be obtained by a normal or chi-square distribution. A common method is to use a Davies's upper bound of the p-value instead of an exact asymptotic p-value. In this paper, we provide a unified sine-cosine process expression of the CA trend test that does not specify the MOI and the TDT that includes the unaffected. We also present a closed form expression of the exact asymptotic formulas to calculate the p-values of the supremum tests when the score function can be written as a linear form in an unidentifiable parameter. We illustrate how to use the derived formulas using a pharmacogenetics case-control dataset and an attention deficit hyperactivity disorder family-based example.