• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.12
• /
• pp.159-164
• /
• 2005

Recently, it has demanded high-speed digital circuits as information increase. Therefore, electromagnetic characteristics of compact microwave circuit occurred importantly. And, the effect of the imperfect ground plane on the signal integrity and influence of coupling between two parallel lines for high-speed digital transmission line on the printed circuit board is investigated by FDTD simulations in 3-D electromagnetic analysis method. The results of FDTD simulation are compared with the ADS simulation in commercial software, analyzed lumped element of modeling and electromagnetic wave's radiation of slot as frequency. As a consequence, when the slot in the ground plane is under microstrip line, it has much effect on propagation of wave.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.6
• /
• pp.1305-1309
• /
• 2013

The application of the superconducting fault current limiter (SFCL) in a power distribution system is expected to contribute the voltage-sag suppression of the bus line as well as the fault-current reduction of the fault line. However, the application effects of the SFCL on the voltage sag of the bus line including the fault current are dependent on its application location in a power distribution system. In this paper, we investigated the fault current limiting and the voltage sag suppressing characteristics of the SFCL due to its application location such as the outgoing point of the feeder, the bus line, the neutral line and the 2nd side of the main transformer in a power distribution system, and analyzed the trace variations of the bus-voltage and fault-feeder current. The simulated power distribution system, which was composed of the universal power source, two transformers with the parallel connection and the impedance load banks connected with the 2nd side of the transformer through the power transmission lines, was constructed and the short-circuit tests for the constructed system were carried out. Through the analysis on the short-circuit tests for the simulated power distribution system with the SFCLs applied into its representative locations, the effects from the SFCL's application on the power distribution system were discussed from the viewpoints of both the suppression of the bus-voltage sag and the reduction of the fault current.

• Journal of Advanced Navigation Technology
• /
• v.25 no.3
• /
• pp.229-235
• /
• 2021

This paper proposes a method of implementing an unequal power divider for high splitting ratios by using transmission lines connected with open and short stubs. The proposed method is an equivalent circuit analysis of a transmission line with an additional port so that it can be converted to an arbitrary impedance in the center of a 2-port transmission line and a 3-port transmission line with an open or short stub connected in parallel to each port. To prove the validity of this method, a Wilkinson power divider with k² = 20 dB splitting ratio and a Gysel power divider with k² = 17 dB splitting ratio were designed at a center frequency of 1 GHz using a 3-port transmission line equivalent circuit. The experimental results of the electrical characteristics are in good agreement with the simulation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.8
• /
• pp.22-29
• /
• 2006

According to the recent revision of KS on the basis of the IEC, equipotential grounding systems has been come into focus and the use of surge protective devices(SPD) has been increased radically in order to operate the power system stably. $Z_nO$ varistor with non-linear resistance, which has an outstanding voltage-current(V-I) characteristic, is mainly used in power system to limit surge voltage and divert surge current. $Z_nO$ varistors are packaged several types based on the circuit assembly to be connected to a.c. power line. When the user assemble the $Z_nO$ varistors into parallel or series circuit package, there are my things to be taken into consideration including functions and thermal stability because they are directly related to the safety. We compare stabilities of each assembly type by measuring residual voltage, discharge current, leakage current and surface temperature concerned to the protection performances between a single device with a 40[kA] of current capacity and parallel or series circuits type of varistor package.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.432-434
• /
• 1994

This paper describes a phase-shifter which can flexibly adjust the active and reactive power flow through an ac transmission line. The phase-shifter has two voltage-source converters sharing an energy storage capacitor. The magnitude of the injected voltage is controlled by the converter I connected in parallel with the sending terminal, while that of phase angle by the converter II in series with the line through the coupling transformer. In order to analyze the whole system operation, an equivalent circuit model was developed and verified by a computer simulation with EMTP code.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.4
• /
• pp.536-544
• /
• 1997

This study presents test results of a residential window system air-conditioner using R22 and two potential alternative refrigerants, R407C and R410B. A series of performance tests was performed for the basic and liquid-suction heat exchange cycle in a psychrometric calorimeter test facility. For R407C, the same rotary compressor was used as in the R22 system. However, compressor for the R410B system was modified to provide the similar cooling capacity. The evaporator circuit was changed to get a counter-cross flow heat exchanger to take advantage of zeotropic mixture's temperature glide, and liquid-line suction-line heat exchange cycle was also considered to improve the performance of the system. Test results were compared to those for the basic R22 system.

• Journal of Information Display
• /
• v.10 no.4
• /
• pp.202-205
• /
• 2009

An automated circuit repair system was developed for enhancing the yield of nondefective liquid crystal panels, focusing on the resist patterns on the circuit material layer of thin-film transistor (TFT) substrates prior to etching. The developed system has an advantage over the parallel conventional system: In the former, the repair conditions depend on the type of resist whereas in the latter, the repair parameters must be fine-tuned for each circuit material. The developed system consists of a resist pattern defect inspection system and a pattern repair system for short and open defects. The repair system performs fine corrections of abnormal areas of the resist pattern. The open-repair system is equipped with a syringe to dispense resist. To maintain a stable resist diameter, a thermal insulator was installed in the syringe system. As a result, the diameter of the dispensed resist became much more stable than when no thermal insulator was used. The resist diameter was kept within the target of $400{\pm}100{\mu}m$. Furthermore, a prototype system was constructed, and using a dummy pattern, it was confirmed that the system worked automatically and correctly.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.8
• /
• pp.555-559
• /
• 2003

In this paper, a new CMOS RF model for RF IC design including the capacitance effect, the skin effect, and the proximity effect between metal lines on the Si surface is proposed for tile first time for accurately predicting the RF behavior of CMOS devices. The capacitances between metal lines on the Si surface are modeled with the layout. And the skin effect is modeled with a parallel branch added in equivalent circuit of metal line. The proximity effect is modeled by adding the mutual inductance between cross-coupled inductances in the ladder circuit representation. Compared to the BSIM 3v3. the proposed RF model shows good agreements with the measured data and shows well the frequency dependent behavior of devices in GHz ranges.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.6
• /
• pp.105-112
• /
• 2010

Recently, wireless communication systems have been developed and the circuits which operate with the broad-band for multiband uses were introduced. However, broad-band circuits have problems that inevitably increase the size. Dual-band circuit operates only two frequency, therefore, it will be able to miniaturize through unnecessary decreased elements. The Wilkinson power divider is the one of the most commonly used components in wireless communication system for power division. Nowaday, the Wilkinson power divider is also demanded dual-band. In this paper, I propose miniaturized dual-band Wilkinson power divider operating at 2.45 GHz and 5.2 GHz for IEEE 802.11n standard. Proposed dual-band Wilkinson power divider is used in parallel stub line. The design is accomplished by transforming the electrical length and impedance of the quarter wave sections of the conventional Wilkinson power divider into dual band ${\pi}$-shaped sections.

• Journal of Advanced Information Technology and Convergence
• /
• v.10 no.1
• /
• pp.71-83
• /
• 2020

In this paper, we propose a system that can detect the shape of a hand at high speed using an FPGA. The hand-shape detection system is designed using Verilog HDL, a hardware language that can process in parallel instead of sequentially running C++ because real-time processing is important. There are several methods for hand gesture recognition, but the image processing method is used. Since the human eye is sensitive to brightness, the YCbCr color model was selected among various color expression methods to obtain a result that is less affected by lighting. For the CbCr elements, only the components corresponding to the skin color are filtered out from the input image by utilizing the restriction conditions. In order to increase the speed of object recognition, a median filter that removes noise present in the input image is used, and this filter is designed to allow comparison of values and extraction of intermediate values at the same time to reduce the amount of computation. For parallel processing, it is designed to locate the centerline of the hand during scanning and sorting the stored data. The line with the highest count is selected as the center line of the hand, and the size of the hand is determined based on the count, and the hand and arm parts are separated. The designed hardware circuit satisfied the target operating frequency and the number of gates.