• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.10
• /
• pp.1126-1135
• /
• 2007

This paper presents the varactor-tuned miniaturized hairpin tunable filter with a single control voltage. The previously proposed miniaturization method is a very straight-forward method to miniaturize a parallel coupled-line filter. In this paper, the miniaturized hairpin tunable filter is proposed with the constant ratio rule of that the capacitances of the each stage always have constant ratio without any dependency to miniaturized electrical length. To show the validity of the proposed method, a 3rd order 0.5 dB ripple Chebyshev fitter with a center frequency of 900 MHz and a fractional bandwidth(FBW) of 10 % was designed and fabricated. The fabricated filter was based on CER-10 substrate of Taconic Inc. with 1SV277 varactor diode of Toshiba Inc. The center frequency of the fabricated filter can be changed from 606 MHz to 944 MHz, 338 MHz with the control voltage from 0.5 V to 4 V. The insertion loss of the proposed filter is increased with the increment of the control voltage, and the filter characteristics are well reserved expect of slight change of the bandwidth with the various control voltage.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.8 no.2
• /
• pp.151-163
• /
• 2006

Although various methods for effective modeling of pre-reinforced zones have been suggested for numerical analysis of large section tunnels, tunnel designers refer to empirical cases and literature reviews rather than engineering methods because ones who use commercial programs are unfamiliar with a macro-scale approach in general. Therefore, this paper suggests a simple micro-scale approach combined with the macro-scale approach to determine equivalent design parameters for effective numerical modeling of pre-reinforced zones in tunnel. This new approach is to determine the equivalent stiffness of pre-reinforced zones with combination of ground, bulb, and steel in series or/and parallel. For verification, 3-D numerical results from the suggested approach are compared with those of a realistic model. The comparison suggests that two cases make best approximation to a realistic solution: One is related to the series-parallel stiffness system (hereafter SPSS) in which bulb and steel are coupled in parallel and then connected to the ground in series, and the other is the series stiffness system (hereafter SSS) in which only bulb and steel are coupled in series. The SPSS is recommended for stiffness calculation of pre-reinforced zones because the SSS is inconvenient and time-consuming. The SPSS provides slightly bigger vertical displacement at tunnel crown in weathered rock than other cases and give almost identical results to a realistic model for horizontal displacement at tunnel spring line and ground surface settlement. Displacement trends on weathered rock and weathered soil are similar. The SPSS which is suggested in this paper represents the behavior mechanism of pre-reinforced area effectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.279-285
• /
• 2017

In this paper, the resonator with a parallel plate capacitor is newly proposed around sub-microwave frequency band and applied to earlobe for non-invasive glucose monitoring the human biological tissue. The capacitor including the earlobe as dielectric material is connected to inductive slot in the ground plane of the microstrip line. Based on the simulation, one port resonator circuit is designed and fabricated as a prototype. Three step glucose concentration levels(0, 250, 500 mg/dL) was tested, and its reflection coefficients($S_{11}$) were measured. Owing to high Q resonator more than 100, resonant frequency shift of about 9 MHz per glucose level of 250 mg/dL has been successfully measured. This proves that the proposed sensor is applicable to a blood glucose sensor.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.7
• /
• pp.144-149
• /
• 2002

This paper presents a technique for real time multiprocessor parallel processing to develop an avionic system computer(ASC) which integrates the avionics control, navigation and fire control, cursive and raster graphic symbol generation into one line replaceable unit. The proposed method has optimal performance by adopting a logically asymmetric structure between four 32bit RISC processors based on the master-slave multiprocessing, a tightly coupled interaction level with the time shared common bus and global memory, and an efficient bus arbitration algorithm. The ASC has been verified through a series of flight tests. The relevant tests also have been rigorously conducted on the prototype ASC such as electrical test, environmental test, and electromagnetic interference test.

• Journal of the Korea Convergence Society
• /
• v.9 no.11
• /
• pp.29-35
• /
• 2018

In this paper, we proposed a high sensitivity sensor that can detect the concentration change of Nacl aqueous solutions by using a slot coupling capacitor resonator in sub-microwave band. The resonator applied to the sensor consists of a parallel plate capacitor connected to an inductive slot utilizing the ground plane of the microstrip line. Based on the measurement data of the dielectric characteristics according to the concentration change, the resonance frequency was determined in the UHF band where the concentration change is evident and the Nacl aqueous solution is inserted into the capacitor. Based on the simulation, the proposed resonator was designed and fabricated. The concentration level was varied from 0 to 400 mg/dl as 100 mg/dl step, and the transmission scattering coefficient ($S_{21}$) was successfully measured. Experimental results show that it is applicable to the concentration detection sensor in Nacl aqueous solution by obtaining minimum 1.8 dB($S_{21}$) at each step.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.411-412
• /
• 2008

The high performance 94 GHz MMIC(Monolithic Micro-wave Integrated Circuit) single balanced mixer was designed and fabricated, using MHEMT structure based diodes and a CPW(Coplanar Waveguide) tandem coupler. A novel single-balanced structure of diode mixer is proposed in this work, where a 3-dB tandem coupler with two section of parallel-coupled line. Implemented air-bridge crossover structures achieve wide frequency operation and the fabricated mixer exhibits excellent LO-RF isolation, larger than 30 dB, in the 5 GHz bandwidth of 91-96 GHz. A good conversion loss of 7.4 dB is measured at 94 GHz. The proposed MHEMT-based diode mixer shows superior LO-RF isolation and conversion loss to those of the W-band mixers reported to date.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.8
• /
• pp.555-559
• /
• 2003

In this paper, a new CMOS RF model for RF IC design including the capacitance effect, the skin effect, and the proximity effect between metal lines on the Si surface is proposed for tile first time for accurately predicting the RF behavior of CMOS devices. The capacitances between metal lines on the Si surface are modeled with the layout. And the skin effect is modeled with a parallel branch added in equivalent circuit of metal line. The proximity effect is modeled by adding the mutual inductance between cross-coupled inductances in the ladder circuit representation. Compared to the BSIM 3v3. the proposed RF model shows good agreements with the measured data and shows well the frequency dependent behavior of devices in GHz ranges.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.5
• /
• pp.238-242
• /
• 2001

In this paper, we extracted design parameters for re-entrant mode microstrip directional coupler using FE(finite element) calculations. The microstrip directional coupler suffers from a poor directivity due to effect of the inhomogeneous dielectric including both dielectric substrate and air in microstrip transmission lines. Thus, the phase velocity of even mode is not equal to that of odd mode. In order to improve the directivity of microstrip directional coupler, a novel re-entrant mode microstrip directional coupler was employed. In microstrip configuration, the high directivity can be reached by matching the even- and odd-mode effective phase velocities. Through the values of capacitance obtained from 2-dimensional FE calculations, the phase velocities for each mode and the design parameter were extracted for the proposed parallel coupled-line configuration. Based on the extracted design parameter with phase matching condition, we designed and fabricated a 30dB directional coupler at 0.85GHz. Experimental results show good performance with excellent, isolation and directivity.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1610-1612
• /
• 2005

In this paper, the inductive power collector using electromagnetic induction for vehicle such as the PRT(Personal Rapid Transit) system is suggested and some ideas for power collector design to improve the power transfer performance are presented. The proposed the inductive power collector is used for the PRT system, which has a large air-gap and demands a large electrical power capability. But, low output power is generated due to a loosely coupled characteristic of the large air-gap. Therefore, double layer construction of secondary winding, which was divided in half to increase both output current and output voltage was suggested. Also, a model of power collector and parallel winding structure and a model of concentration/decentralization winding are presented, in addition, the performance of inductive power collector to alignment condition between the primary power line and the inductive power transformer was verified by computer simulation of 2kW model.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.7 s.361
• /
• pp.105-111
• /
• 2007

In this paper, we designed and fabricated a 3-dB tandem coupler using air-bridge technology for millimeter-wane monolithic integrated circuits, operating at W-band($75{\sim}110\;GHz$) frequency. Tightly edge-coupled CPW line has low directivity due to different even-mode and odd-mode phase velocity. To overcome this disadvantage, a 3-dB tandem coupler which comprises the two-sectional weakly parallel-coupled lines with equal phase velocity was designed at W-band. The proposed coupler was fabricated using air-bridge technology to monolithically materialize the uniplanar coupler structure instead of conventional multilayer or wire bonded structure. From the measurements, the coupling coefficient of $2.9{\sim}3.6\;dB$ and the good phase difference of $91.2{\pm}2.9^{\circ}$ were obtained in broad frequency range of $75{\sim}100\;GHz$.