• Computers and Concrete
• /
• v.22 no.4
• /
• pp.407-417
• /
• 2018

Over the past three decades, self-compacting concrete (SCC), which is characterized by its superior rheological properties, has been gradually used in construction industry. It is now recognized that the application of SCC using supplementary cementitious materials (SCM) is highly attractive and promising technology reducing the environmental impact of the construction industry and reducing the higher materials costs. This paper presents an experimental study that investigated the mechanical and durability properties of SCCs manufactured with blended binders including fly ash, slag, and micro-silica. A total of 8 batches of SCCs were manufactured. As series of tests were conducted to establish the rheological properties, compressive strength, and durability properties including the water absorption, water permeability, rapid chloride permeability and initial surface absorption of the SCCs. The influences of the SCC strength grade, blended types and content on the properties of the SCCs are investigated. Unified reactive indices are proposed based on the mix proportion and the chemical composition of the corresponding binders are used to assess the compressive strength and strength development of the SCCs. The results also indicate the differences in the underlying mechanisms to drive the durability properties of the SCC at the different strength grades.

• Advances in concrete construction
• /
• v.9 no.3
• /
• pp.267-278
• /
• 2020

This paper reports on the result of an experimental investigation carried out to study the compressive strength and sorptivity properties of blended cement concrete exposed to 5% and 10% MgSO₄ solution using fly ash (FA) and silpozz. Usually in sulphate environment the minimum grade of concrete is M30 and the mix design is done for target mean strength of 39 MPa. Silpozz is manufactured by burning of agro-waste rice husk in designed furnace in between 600° to 700℃ which is one of the main agricultural residues obtained from the outer covering of rice grains during the milling process. There are four mix series taken with control mix. The control mix made 0% replacement of FA and silpozz with Ordinary Portland Cement (OPC). The first mix series made 0% FA and 10-30% replacement of silpozz with OPC. The second mix series made with 10% FA and 10-40% replacement of silpozz with OPC. The third mix series made 20% FA and 10-30% replacement of silpozz with OPC and the fourth mix series made 30% FA and 10-20% silpozz replaced with OPC. The samples (cubes) are prepared and cured in normal water and 5% and 10% MgSO₄ solution for 7, 28 and 90 days. The studied parameters are compressive strength and strength deterioration factor (SDF) for 7, 28 and 90 days. The water absorption and sorptivity tests have been done after 28 days of normal water and magnesium sulphate solution curing. The investigation reflects that the blended cement concrete incorporating FA and silpozz showing better resistance against MgSO₄ solution when compared to normal water curing (NWC) samples.

• Advances in aircraft and spacecraft science
• /
• v.4 no.1
• /
• pp.37-52
• /
• 2017

Gas turbines operating in dusty or sandy environment polluted with micron-sized solid particles are highly prone to blade surface erosion damage in compressor stages and molten sand attack in the hot-sections of turbine stages. Commercial/Military fixed-wing aircraft engines and helicopter engines often have to operate over sandy terrains in the middle eastern countries or in volcanic zones; on the other hand gas turbines in marine applications are subjected to salt spray, while the coal-burning industrial power generation turbines are subjected to fly-ash. The presence of solid particles in the working fluid medium has an adverse effect on the durability of these engines as well as performance. Typical turbine blade damages include blade coating wear, sand glazing, Calcia-Magnesia-Alumina-Silicate (CMAS) attack, oxidation, plugged cooling holes, all of which can cause rapid performance deterioration including loss of aircraft. The focus of this research work is to simulate particle-surface kinetic interaction on typical turbomachinery material targets using non-linear dynamic impact analysis. The objective of this research is to understand the interfacial kinetic behaviors that can provide insights into the physics of particle interactions and to enable leap ahead technologies in material choices and to develop sand-phobic thermal barrier coatings for turbine blades. This paper outlines the research efforts at the U.S Army Research Laboratory to come up with novel turbine blade multifunctional protective coatings that are sand-phobic, sand impact wear resistant, as well as have very low thermal conductivity for improved performance of future gas turbine engines. The research scope includes development of protective coatings for both nickel-based super alloys and ceramic matrix composites.

• Korean Journal of Remote Sensing
• /
• v.29 no.5
• /
• pp.581-588
• /
• 2013

We developed the three channel lidar system to measure stratospheric aerosols at the Gwangju Institute for Science and Technology (GIST), a suburban site in Republic of Korea. The system provides backscatter coefficient (${\beta}$) at 532 and 1064 nm as well as depolarization ratios (${\delta}$) at 532 nm ($2{\beta}+1{\delta}$) using the doubled Nd:YAG laser wavelength at 532 and 1064 nm. The lidar system is optimized to measure stratospheric aerosols such as volcanic ashes. This paper describes the details of the optical setup, data acquisition system, and analysis method. This study shows an example of measuring stratospheric aerosols emitted by the volcanic eruption which occurred in Mt. Nabro ($13.37^{\circ}$ N, $41.70^{\circ}$ E).

• Journal of the Korea Organic Resources Recycling Association
• /
• v.14 no.3
• /
• pp.138-147
• /
• 2006

In this study, the composition and physico-chemical characteristics of municipal solid waste (MWS) which was treated in national park area kyungnam-do landfill were investigated. It is necessary to measure the characteristics of MSW and sludge to build a waste treatment facility, the data-base and total managing of the landfill. This MSW was composed of 34.62% of food wastes, 36.05% of papers, 15.37% of plastics & vinyls, 2.28% of textiles, 3.33% of wood, 0.49% of rubber & leathers and others, respectively. Most of MSW are composed of food, paper and plastic waste and more than 90% was combustible waste. For three components, moisture is 29.84%, combustible component is 62.30% and ash is 7.86%. The chemical element has the high order of carbon, oxygen, hydrogen on the dry basis of wastes. Also, the low heating value of the MSW which is measured by calorimeter is calculated as 2377.8kcal/kg. low heating value of the sludge is calculated as 338.06kcal/kg.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.16 no.1
• /
• pp.70-78
• /
• 2008

In this study, the composition and physico-chemical characteristics of school waste which is located in B area, kyunggi-do was investigated. It is necessary to measure the characteristics of school waste to build the data-base for resource and recycling of waste. This school waste was composed of 12.25% of food wastes, 56.26% of papers, 9.26% of plastics&vinyls, 1.52% of textiles, 3.70% of wood, 0.11% of rubbers&leathers and others, respectively. Most of school wastes are mainly composed of paper and plastic waste and composition of combustible waste was about as 90%. From 3-components analysis, contents of moisture, combustible component, and ash was 5.72%, 88.29% and 5.98%, respectively. Moisture content was higher in Agricultural Dwelling school area compare to the urban dwelling school area. The chemical element of the school waste has the high order of carbon, oxygen, hydrogen on the dry basis of wastes and the low heating value of the MSW which is measured by calorimeter is shown as 3720.44kcal/kg.

• Journal of Information Technology Services
• /
• v.10 no.2
• /
• pp.177-188
• /
• 2011

This paper proposes a DEA model for the performance evaluation of each brand of coking coals in an integrated steel mill. The performance is defined as the efficiency which is the ratio of two linear combinations of the output factors to the input factors. There is only one input factor considered in the model : unit price of each brand based on CIF. Five output factors are chosen in consideration of their impact to the quality of cokes such as Ash, VM, LMF, TD, and Rm. Some of the output factors are treated as undesirable in DEA model because the quality criteria are given by the range. The CCR and BCC efficiencies are derived by the DEA model, and the scale efficiency is calculated, too. Each brand of coking coal is classified into four categories according to the CCR and BCC efficiencies, and the most inferior brands are identified as a result. The impact of the input and output factors to the efficiency is analyzed using a multiple regression, then the unit price is revealed as the most critical among them. Also, ANOVA results show that there exist efficiency differences among the coal types and the countries imported, respectively. Finally, the quantitative projection for the inefficient brands is performed if they are to be efficient. The result could be utilized in selecting the good or bad brands of coking coal based on the efficiency in an integrated steel mill. Also, this model will be used to assess the relative efficiency of a new brand of coking coal if it is a candidate to be imported.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.689-692
• /
• 2008

HSC(High Strength Concrete) have superior properties well as improvement in durability compared with normal strength concrete. In spite of durability of HSC, explosive spalling of concrete is serious problem in structure safety. Therefore, Solving methods are required to control the explosive spalling. The properties of concrete are affected by changes of temperatures. Compressive strength and elasticity modulus were degraded depending on a rise of temperatures. Also, change in microstructure and dehydration of concrete subjected to high temperatures. This paper is concerned with change in microstructure and dehydration of the alumino silicate fire protection materials at high temperatures. The testing methods of fire protection materials in high temperature properties are make use of SEM, TG-DSC and XRD. From the experimental test results, influence of high temperatures on microstructure of alumino-silicate fire protection material was identified, including chemical dehydration of C-S-H and CH. The chemical dehydration of CH under various temperatures from to 450 to 600$^{\circ}$C has been measured using the TG-DSC. However, developed alumino silicate fire protection materials showed good stability in high Temperatures. Thus, the results indicate that it is possible to fireproof panels, fire protection of materials.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.3
• /
• pp.173-180
• /
• 2013

This paper is to investigate an effect of waste cooking oil(WCO) on the engineering properties and durability of high volume admixture concrete. Fly ash with 30% and blast furnace slag with 60% were incorporated in OPC to fabricate high volume admixture concrete with 0.5 of W/B. Emulsified refining cooking oil(ERCO) was made by mixing WCO and emulsifying agent to improve fluidity. ERCO was replaced by cement from 0.25 to 1.0%. As results, the increase of ERCO resulted in decrease of slump and air contents. For compressive strength, the use of ERCO led to decrease the compressive strength at 28 days, while it had similar strength or much higher strength than plain concrete at 180 days. Resistance to carbonation and chloride penetration was improved with the increase of ERCO contents due to decreased pore distribution by saponification between ERCO and concrete, while freeze-thaw resistance was degraded due to air loss.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.3
• /
• pp.292-303
• /
• 2002

This paper presents experimental results for early-age properties of concrete such as the setting time and strength, evaluated via the ultrasonic pulse velocity (UPV). Developing and using an automatically-recording monitoring system, the UPV's of mortar and concrete with various water to binder ratios (W/B) were measured during the first 24 hours. In addition, probe penetration and compression tests were conducted to measure the setting time and compressive strength, respectively. It was observed that the UPV's of mortar with high W/B remained constant during the first 6.5 hours and then abruptly began to increase at constant rates. On the other hand, the UPV of mortar with low W/B increased relatively slowly and gradually due to the setting retardation caused by the use of high range water reducing agent (HRWR). It was found that setting of concrete occurs when the UPV reaches a certain value. Moreover, it was concluded that the estimation formulas should incorporate the effects of W/B to more accurately estimate the early-age strength of concrete from the UPV.